Resistor is used as load in the circuit below. T1 and T4 thyristor is triggered at 30 degrees, T2 and T3 thyristor is triggered at 210 degrees. The effective voltage of the AC voltage applied to the circuit is 120 V. V(t) T3 T2 T4 LOAD a) Draw the graph of the voltage on the load resistor. b) Neglect the voltage drop across the thyristors and find the average value of the load voltage.

Resistor is used as load in the circuit below. T1 and T4 thyristor is triggered at 30 degrees, T2 and T3 thyristor is triggered at 210 degrees. The effective voltage of the AC voltage applied to the circuit is 120 V. V(t) T3 T2 T4 LOAD a) Draw the graph of the voltage on the load resistor. b) Neglect the voltage drop across the thyristors and find the average value of the load voltage.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 4PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l3l4RTR182kR275kR356kR462kPT3.436WP1P2P3P4
A circuit consists of an AC voltage source, a 10-ohm resistor, and a capacitor, all connected in series. The magnitude of the impedance of the capacitor is also 10 ohms. Which of the following is true about the source voltage and the current through the circuit? a. Insufficient information is given. b. The source voltage will lag the current. c. The source voltage will lead the current. d. The source voltage will be in-phase with the current.
An AC circuit is shown in the diagram. The source of emf has a peak voltage of 9.00 V and a frequency of 60.0 Hz. Assume the wires contribute a negligible amount to the resistance and the AC source has negligible internal resistance. 524 2 493 2 1.56 k2 a) Find the equivalent resistance of the circuit. Redraw the circuit showing the equivalent resistor and use this simplified circuit for the rest of the problem. 315 2 Re = b) Find the rms current. 9.00 V, 60.0 Hz c) If the current is zero at time t= 0, find the first two times (after time t-0) that the current is equal to its rms value. and d) Find the average power dissipated by the circuit.
A 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of158 volts, 50 Hz supplies the combination. Determine the following:a. Circulating currentb. Voltage across the resistorc. Voltage across the capacitord. Real power supplied by the source
There era two type of currents, a. direct current and b. alternating current. For each of these type, name as many as you can the specific application and discuss them as to their effectiveness And safety.
please write introduction about AC Circuits and Parallel Circuits
Which of the following statement is true? a. Angle between load voltage and load current in a pure capacitive load is 45 degree. b. Angle between load voltage and load current in a pure capacitive load is is 180 degree. c. Angle between load voltage and load current in a pure capacitive load is is zero. d. Angle between load voltage and load current in a pure capacitive load is is 90 degree.
The temperature of a noninductive heater unit is controlled by a reactor. The heater unit and the reactor are connected in series across a 250 V, 60 Hz source. The voltage across the heater unit is 200 V. The voltage across the reactor is 100 V. The current in the circuit is 10 A. Determine: the power factor of the series circuit. the power factor of the reactor. the impedance of the reactor. the effective resistance of the reactor. the inductive reactance of the reactor
3) Resistor is used as load in the circuit below. T1 and T4 thyristor is triggered at 30 degrees, T2 and T3 thyristor is triggered at 210 degrees. The effective voltage of the AC voltage applied to the circuit is 120 V. a) Draw the graph of the voltage on the load resistor.b) Neglect the voltage drop across the thyristors and find the average value of the load voltage.
a) Graphically show the differences between alternating current voltage (A.C) and direct current voltage (D.C). What are the advantages of A.C compared to D.C?
The step down DC chopper uses DC source voltage V(dc) = 200 V and resistive load impedance of 10 ohm. The duty cycle is 0.4 the voltage drop across the switch may be taken as zero, Calculate : (a) Average and RMS value of output voltage. (b) Average and RMS value of output current.
Given the circuit in Figure 04 and defining that: Vs = 100 sin (wt) Volts and the firing angle of the thyristors T1 and T2 is equal to 110° and that T3 and T4 have similar firings in the negative half-cycle of Vs. a)Sketch the output voltage waveform for a highly inductive load. b) Sketch the waveform output voltage, replacing the highly inductive load with a purely resistive load. c) Get the value of the average output voltage when the load is purely resistive.