B4 Required informotionNOTE: This is a multi-part question Once an answer is submitted, you will be unable to return to this partConsider the given figure2 kN SSR QQ P0.8 m 0.8 m 0.8 m 0.8 m 0.8 m 0.8 mDE G H0.4 mcesA fioor truss is loaded as shown. Determine the force in members CF, EF, and EG Assume P1 kN, Q=8 KN. R=6 KN and S4 kN.The force in member CFisThe force in member EFIThe force in member EGISkN (Click to select)KN (Click to select)kN (Click to select) v

Answered: Image /qna-images/answer/fcdbe6fd-8440-4226-8822-71eb013b3b4d.jpg

Required informetion NOTE: This is a multi-part question Once an answer is submitted, you will be unable to return to this part Consider the given figure 2 kN S R 0.8 m 0.8 m 0.8 m 0.8 m 0.8 m 0.8 m D E GY H 0.4m A floor truss is loaded as shown. Determine the force in members CF, EF, and EG Assume P1 kN, Q8 kN. R6 kN and S4 kN. The force in member CF is The force in member EFis The force in member EGIS kN (Cick to select) v KN (Click to select) v KN (Cick to select)

Required informetion NOTE: This is a multi-part question Once an answer is submitted, you will be unable to return to this part Consider the given figure 2 kN S R 0.8 m 0.8 m 0.8 m 0.8 m 0.8 m 0.8 m D E GY H 0.4m A floor truss is loaded as shown. Determine the force in members CF, EF, and EG Assume P1 kN, Q8 kN. R6 kN and S4 kN. The force in member CF is The force in member EFis The force in member EGIS kN (Cick to select) v KN (Click to select) v KN (Cick to select)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. The following the truss figure, came from your Module 1. Page 9. B D F 3 m H H. E G 30 kN 70 kN 4 panels at 4 m = 16 m But this time, All the members have a cross sectional area of 850 mm². Find the normal stress of the following members а. EF b. GH c. DF
The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontalbefore the load P is applied. Determine the maximum value for P If the stress must not exceed: 160 MPa for steel and 80 MPa for Bronze. Then determine the vertical movement of P. STEEL Lm A-400 mm E-200 GPa BRONZE L-5m A-500 mm E-80 GPa 3m
2. Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 10 kN? Specify whether tension or compression. Bronze Aluminum Steel A =400 mm2 A= 600 mm2 A = 300 mm2 2P ЗР 4P P -3 m 5 m 4 m Stress in Bronze (MPa) %D Stress in Aluminum (MPa) %3D Stress in Steel (MPa)
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 15 kN? Specify whether tension or compression. Bronze Aluminum Steel A=400 mm? A=600 mm? A= 300 mm? 2P 3P 4P P -3 m + 5 m -4m
Two aluminum (Ea=77 GPa) rods AB and CD, and a steel (Es=202 GPa) rod EF support a 82.7 kN load P. Each of the rods has a 400 mm2 cross- sectional area. Neglecting the deformation of rod BED, determine the change in length (in mm correctly up to two decimal places) of rod AB. A C P 500 mm В E 400 mm F
2.47 The negligible weight rigid bar is pinned at O and attached to two vertical rods. WI is the largest load P that can be applied without exceeding stresses of 150 MPa in t steel rod and 70 MPa in the bronze rod, assuming the rods were initially stress-free? 4m 3m 3m Steel A = 600mm2 E = 83Gpa L = 4m Steel V P A = 1800mm2 E = 200Gpa L 3m
Determine the normal stress (in Mpa) in member AB of the truss shown if it is made up of a 14-mm-square bar of alloy and the load P is 21.53 kN. Express your answer in two decimal places.
Two plate are joint by five rivets of 20 mm diameter. What is the shear stress in the material if the shear forces is 18840 N O 12 N/mm2 O 20 N/mm2 O 15 N/mm2
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Two members, each consisting of a straight and a quarter-circular portion of rod, are connected as shown and support a load P=135.0 lb at A P -6 in -3 in--3 in- B Determine the internal forces at point J The axial force Fis[ The shear force Vis The bending moment Mis E lb 4 Problem 07.156.b - Determine internal forces. lb A -6 in. D 3 in O 3 in. 3 in. lb in acting in the (Click to select) direction.
The horizontal bar ABC is supported by a pin at A and two rods with identical cross- sectional areas. The rod at B is steel and the rod at C is aluminum. Neglecting the weight of the bar, determine the force in each rod when the force P = 80 kN is applied. Use Est = 200 GPa and Eal = 70 GPa. %3D Steel Aluminum A B T2 m- 1.5 m- Im
Problem 1 A rigid bar AC is loaded and supported as shown. Bar AB and CD are unstressed before the load is applied. Bar AB is made of steel (E = 30000ksi) and has a cross-sectional area of 1.25 in?. Bar CD is made of brass (E = 15000ksi) and has a cross-sectional area of 0.75 in². Determine: %3D 12 k/ft (1) The stresses in bars AB and CD (2) The vertical displacement (deflection) of C relative to the displacement at point (Note: express your answer in inches and include a direction) TI!||! 3 ft 4.5 ft