Required information The small turbine in given figure extracts 400 W of power from the water flow. Both pipes are wrought iron. For water, take p = 998 kg/m3 and u = 0.001 kg/m-s. For wrought iron, take ɛ = 0.046 mm. Water 20 m 20°C Turbine 10 m D = 6 cm 30 m D = 4 cm For the given two flow rates obtained are Q1 = 15.7 m3/hr and Q2 = 9 m3/hr. Both the solutions are valid, but the flow i Q1 is preferred over Q2. True or False True False

Required information The small turbine in given figure extracts 400 W of power from the water flow. Both pipes are wrought iron. For water, take p = 998 kg/m3 and u = 0.001 kg/m-s. For wrought iron, take ɛ = 0.046 mm. Water 20 m 20°C Turbine 10 m D = 6 cm 30 m D = 4 cm For the given two flow rates obtained are Q1 = 15.7 m3/hr and Q2 = 9 m3/hr. Both the solutions are valid, but the flow i Q1 is preferred over Q2. True or False True False

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The water is flowing through a pipe having diameters 40 cm and 15 cm at sections 1and 2 respectively. The rate of flow through pipe is 35 litres/s. The section 1 is 7 m above datum and section 2 is 3.5 m above datum. If the pressure at section 1 is 36 N/cm?, find the following by neglecting losses: (ENTER ONLY THE VALUES BY REFERRING THE UNIT GIVEN IN BRACKETS)
1.28. The performance curve for the fan of Problem 1.27 can be approx- imated by a straight line through its BEP (using techniques devel- oped in Chapter 7). The curve is Aps = 4488 – 166Q, with ApT in Pa and Q in m³/s. If this fan is connected to a 1-m dia- meter duct (f = 0.045) whose length is 66 m, what flow rate will result? %3D
Q.4. In the system shown in figure, the water flow rate ,Q= 0.5 m3/s and pressure P=20 kPa are required at the point C. Calculate flow directions and flow rates in the pipes and power of the pump required in the system. Draw the energy lines in the system. Note: Neglect the local losses and take f=0.02 in the analysis. B ZA-20 m ZB=40 m 3 zc=4 m ZD=0 m A 2 Li=95 m, L2=120 m, L3=100 m 1 L2= 125m Pump D= 30 cm D k=0.046 mm
2500kW power is generated shown in the Figure with a water flowrate of 20 m3/s. The head loss for the entire flow is 2.5m. (a) Find the pressure difference P1 - P2 across the turbine. (b) Find h You can neglect the head loss between point 1 and 2.
3. Water is pumped through three pipes in series. Compute the discharge if the power delivered to the pump is W₂ = 1920 kW and the pump efficiency is n = 82%. The pipe resistance coefficients are R₁ = 13.2 s²/m³, R₂ = 204.1 s²/m³, R₂ = 25.8 s²/m³, and the head difference between the downstream and upstream reservoirs is 50 m. Ans: Q = 0.792 m³/s
1.A pipe of diameter 300 m and length 3000 m is used for the transmission of power by water. The total head at the Inlet of the pipe is 400 m. Find the maximum power available at the outlet of the pipe. Take f=0.005 2. The head of water at the Inlet of a pipe of length 1500 m and diameter 400 mm is 50 m. A nozzle of diameter 80 mm at the outlet, is fitted to the pipe. Find the velocity of water at the outlet of the nozzle if f=0.01 for the pipe.
Water from a reservoir passes over a dam through a turbine and discharges from a 70-cm ID pipe at a point 95 m below the reservoir surface. The turbine delivers 0.950 MW. Calculate the required flow of water in m3/min if friction is neglected. If friction were included would a higher or lower flow rate be required? (Note: The equation you will solve in this problem has multiple roots. Find a solution less than 1.0 m3/s.) V=___m^3/min?
Design a pipe system to supply water at 20° C from the elevated tank to the demand point at the discharge rate of 2.5 m3/s (see figure below). Take these steps:1. Identify your system elements. You have 400 m long pipe system that has one 90° bends. 2. Account for minor losses caused by the bend (use K = 0.18), by the valve (use K = 0.2), entrance loss from elevated tank to pipe (use K = 1) and exit loss from pipe to demand point (use K = 0.5) 3. Set the Energy equation to find the total head loss magnitude (hL). 4. Break down the total loss into friction (hf) and minor losses (hM). Use D-W and minor loss equations to find a relationship between Diameter (D) and Friction Factor (f) (both are unknown). In the equation, replace velocity with Q/A to have only D and f as unknowns. 5. Your other equation to find the 2 unknowns is the Moody diagram. Because both equations are non-linear, numerical iteration is needed. After contacting a nearby vendor, you realize that a convenient pipe…
A pumping station wet well operates between 540- and 550-ft elevation. The pump curve is deϐined by the following points: 80 ft at zero ϐlow, 78 ft at 200 gpm, 65 ft at 800 gpm, and 50 ft at 1200 gpm. The pump discharge contains an equivalent of 50 ft of 6-in. pipe. The discharge pipe is 120-ft long and terminates at a splitter box, elevation 570. Using C=100, plot the pump curve and the corrected pump curve. Plot the pump discharge curves at each wet well elevation and for C=100 and C=140. What is the pump ϐlow at the low and high wet well elevations for newand old pipe?
Length and dia. Of pipe 1 are 2000m and 1m while the second pipe is 2000m and dia. Of 0.8m .Find the rate flow of each pipe if the total flow rate in the main pipe is 0.3 m3/s. the coefficient friction of each pipe is same and equal to 0.05. Ans.Q1= 1.906 m3/s , Q2=1.094m3/s Ex. A pipe of dia.=20cm and length 2000m is connects two reservoir having difference of water levels as 20m determine the discharge through pipe. If an additional pipe of diameter 20cm and length 1200 m is attached to the last 1200m length of the existing pipe, find the increase in the discharge. f=0.015 neglect minor losses. Ans.Q= 0.0254 m3/s , increase to discharge 0.0088m3/s Ex. Pipe of L=4000m and dia.=0.6m as shown in fig. At a distance of 1000m from the upper reservoir , a small pipe is connected to the pipe line. The water can be taken from the small pipe. Find discharge to the lower reservoir a- No water is taken from the small pipe b-100 liter/sec of water is taken from small pipe. f30.005 neglect minor…
Q2/ A pump delivers water from a tank A (water surface elevation = 110 m) to tank B (water surface elevation = 170 m) as shown in figure below. The suction pipe is 45 m long ( = 0.024) and 35 cm in diameter. The delivery pipe is 950 m long (f = 0.022) and 25 cm in diameter. The head discharge relationship for the pump is given by H, = (90 – 8000 Q*), where H, in m and Q in m³/s. Calculate the discharge in the pipeline and the power delivered by the pump. Delivery pipe. elevation 170 m Suction pipe, elevation- 110 m Good Luck Rasha H. Salman
1Two water pumps are arranged in series. The performance data for both pumps follow the parabolic curve fit Havailable =H0 =aV ^2. For pump 1, H0 =5.30 m and coefficient a =0.0438 m/Lpm^2; for pump 2, H0 =8.70 m and coefficient a =0.0347 m/Lpm^2. In either case, the units ofnet pump head H are m, and the units of capacity V are Lpm.Calculate the combined shutoff head. Complete Answer, thank you