Required information NOTE: This is a multi-part question. Once an answer submitted, you will be unable to return to this part. Water is pumped from a lake to a storage tank 15 m above at a rate of 98 L/s while consuming 15.4 kW of electric power. Disregarding any frictional losses in the pipes and any changes in kinetic energy, answer the questions that follow. We take the density of water to be p = 1000 kg/m³. Storage tank 15 m Pump

Required information NOTE: This is a multi-part question. Once an answer submitted, you will be unable to return to this part. Water is pumped from a lake to a storage tank 15 m above at a rate of 98 L/s while consuming 15.4 kW of electric power. Disregarding any frictional losses in the pipes and any changes in kinetic energy, answer the questions that follow. We take the density of water to be p = 1000 kg/m³. Storage tank 15 m Pump

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Show your complete solution for each problem. Only the final answer in your calculation should be rounded off to two decimal digits. Box your final answer. 1. The increase in the specific internal energy is 33.8 BTU/Ibm in a reciprocating compressor draws 40 lbm/min of air whose density is 0.074 lbm/ft³ and discharge it with a density of 0.311 lbm/ft³. At the suction, the pressure is 18 lb:/in² and discharge 88 lb:/in². If the changed in kinetic energy was neglected, determine the work on the air in horsepower (hp).
Suppose that 6 J of work is needed to stretch a spring from its natural length of 32 cm to a length of 46 cm. (a) How much work (in J) is needed to stretch the spring from 37 cm to 41 cm? (Round your answer to two decimal places.) (b) How far beyond its natural length (in cm) will a force of 40 N keep the spring stretched? (Round your answer one decimal place.) cm
3. Please calculate the annual electricity production of a wind farm with 20 turbines. The annual mean wind speed is 7 m/s and diameter of the blades is 20 m. If we assume power consumption of a person is 3,000 kWh, about how many people will this energy support? Annual electricity production (KWh) = K Vm³ At T Where: - - - K = 3.2 (factor based on turbine performance) Vm= annual mean wind speed (m/s) At = swept area of turbine (m2) T = number of turbines Suitable for medium- to large-scale wind turbines (> 200 m2 swept area)
An electric motor is used to drive the shaft of a small water pump. During a performance test, the torque on the motor shaft is found to be 5.014 N⋅m when the motor is drawing 638.52 W of electrical power. What is the rotational speed of the shaft in rpm?
The wind velocity on the upstream side of a wind turbine is 4 m/s. If the turbine extracts 26% of the available kinetic energy, what is the wind velocity on the downstream side of the turbine in m/s? Please include one decimal place in your answer.
You only know one point on a pump curve, where a water pump produces 20 m of hydraulic head at flow rate of 3.67 L/s, and you want to use this to pump water from a lower tank to an upper tank located 15 m higher. Both tanks are open to the atmosphere. Briefly explain your reasoning, in 1‐2 sentences, for each of the following. a) Should this pump be placed next to the lower tank or the higher one? b) Given the data point you have from the pump curve, will the flow rate be higher or lower than 3.67 L/s if the water is pumped exactly 15 m uphill?
2. The diameters of the suction and discharge pipes of a pump are 15 and 10 cm, respectively. The discharge pressure is read by a gage at a point 1.5 m above the centerline of the pump and the suction pressure is read by a gage 0.6 m below the centerline. If the pressure gage reads 140 kPa and the suction gage reads a vacuum of 21 cm Hg when gasoline is pumped at the rate of 35 l/sec (sg of gasoline is 0.75) a. Find the energy added by a pump. (. b. Find the power delivered to the fluid in kW. c. Find the required rating horsepower of the pump if it has an efficiency of 75% 0.10 mg Pz=140 kPa 1.5 m 0.6 m KD Pj=-0.21 m Hg 0.15 mø
Q3. The data listed in the following table gives hourly measurements of heat flux q (cal/cm? /h) at the surface of a solar collector. As an architectural engineer, you must estimate the total heat absorbed by a 150,000-cm2 collector panel during a 14-h period. The panel has an absorption efficiency eab of 45%. The total heat absorbed is given by: h = eab q A where A = area and g = heat flux. 4 6. 10 12 14 0.10 5.32 7.80 8.00 8.03 6.27 3.54 0.20
Patm 1. Initially; the piston sits on the stops and the linear spring exerts no force, the specific volume is 0.05 m /kg and the pressure is 125 kPa. Atmospheric pressure is 100 kPa, mass of the piston is 102 kg, and area of the piston is 200 cm?. The linear spring exerts a force on the piston in such a way that the specific volume becomes 0.08 m'/kg when the pressure reaches 200 kPa. Heat is transferred to the water until its temperature is 115 °C. Calculate work and heat transfer, showing the process on a P-v plot. Hint: In the final stage, the temperature is 115°C, but the pressure is not given. You need to find P and v using the tables and P-v plot.
A fluid is contained in a cylinder by a spring-loaded, frictionless piston so that the pressure in the fluid is linear function of the volume (p = a + bV). The internal energy of the fluid is given by the following equation U = 34 + 3.15 pVwhere U is in kJ, p in kPa and V in cubic metre. If the fluid changes from an initial state of 173 kPa, 0.03 m3to a final state of 400 kPa, 0.06 m3, with no work other than that done on the piston, find the direction and magnitude of the work and heat transfer.
A 542 kg hammer of a pile driver is lifted 3.1 meters above a piling head. If the hammer is released, what will be its velocity (in m/s) at the instant it strikes the piling?
AE ll ll A:£0 docs.google.com/forms When a stationary mass of gas was compressed without friction at constant pressure its initial state of 0.8 m3 and 0.105 MPa was found to change to final state of 0.40 m3 and 0.105 MPa. There was a transfer of 85 kJ of heat from the gas during the process.How much did the internal energy of the gas change ? * 1 Add File Derive the law pv^y = constant * 1 Add File Вack Next Never submit passwords through Google Forms. This form was created inside L Iniversity of Al-