Replace the force system acting on a plate by a single force and determine where the line of action of this force intersects the x-axis and the y-axis. 180 N -240 mm- 300 N 70° 15 63 N.m 120 N 500 mm 60 N.m 180 mm 150 mm -300 mm- -600 mm-

Replace the force system acting on a plate by a single force and determine where the line of action of this force intersects the x-axis and the y-axis. 180 N -240 mm- 300 N 70° 15 63 N.m 120 N 500 mm 60 N.m 180 mm 150 mm -300 mm- -600 mm-

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.48P: The pole OB is subjected to the 6004b force at B. Determine (a) the rectangular components of the...

See similar textbooks

Related questions

Q: Replace the loading by a single resultant force, specify the location of force measured from point…

A: Note that, the center of mass of a uniformly varying loading (UVL) acts at the position of two-third…

Q: Determine the magnitude of the resultant force (in N) of the coplanar force system shown in the…

A: Given data: - The force P is P = 212 N. The moment M is M = 663 N. The height of the region is h =…

Q: 2) Replace the force system acting on the post by a resultant force, and specify where its line of…

A: We have to determine the line of action interests the post AB form point A

Q: 80kN 30kN/m 40KN/m 1m- -1m 3m- 2m

Q: 300 N Replace the loading on the frame by a single resultant force. Specify where its line of action…

Q: 2/121 A 50-lb force is applied to the control pedal as shown. The force lies in a plane parallel to…

Q: Replace the loading system by an equivalent resultant force and specify where the resultant's line…

Q: Determine the magnitude of the resultant force (in N) of the coplanar force system shown in the…

A: To calculate the resultant, we need to first resolve the forces in vertical and horizontal…

Q: Q3/ Replace the two forces acting on the bent pipe by a single equivalent force R. Specify the…

Q: Q1: If F, - 150 lb and e- 55', determine the magnitude and direction measured clockwise from the…

A: As per policy, first question is answered in detail. Second question can be posted as separate…

Q: please answer the question

A: Take x=20m and y=5m

Q: 300 N 250 N b) Replace the loading on the frame by a single resultant force. Specify where its line…

Q: Represent the resultant of the force system acting on the pipe assembly by a single force R at A and…

Q: Q2: Determine the magnitude of forces FA and FB acting on each chain in order to develop a resultant…

Q: Determine the magnitude and direction angles of the resultant force acting on the flag pole. FB =…

Q: 2/7 The two structural members, one of which is in ten- sion and the other in compression, exert the…

Q: 2- Determine the Vertical and Horizontal Component of force at point A and D

A: Option 1 is correct. Ax = 24 kN, Ay = 12 kN, Dx = 18 kN, Dy = 24 kN

Q: Q.3- If= 30°If and F1 = 250 lb, determine the magnitude of the resultant force act- ing on the…

Q: M N m A 150 N 300 mm -250 mm P N 90 N 400 mm

A: Here, we are only interested in resultant force and not the resultant moment. So consider below…

Q: Find the resultant ( R ) of the force system shown. Show its position with respect to point (0).…

A: Given: A force applied to the system is magnitude os 500 N, 200 N, 400 N and 150 N. The moment is…

Q: 3. Determine the resultant force and specify where it acts on the beam measured from A. 9 kN/m 6…

A: As per bartleby guidelines we are allowed to solve only 1st question if multiple questions are…

Q: The cable AB prevents bar OA from rotating clockwise about the pivot O. If the cable tension is 850…

Q: Q2. Replace the force system acting on the frame by an equivalent resultant force and specify where…

A: Moment: The moment is the product of the force with perpendicular distance between the force and…

Q: Replace the loading on the frame by a single resultant force. Specify where its line of action…

A: Let the resultant force F is acting at a distance of x from the point A in member AB, whose…

Q: The cable AB prevents bar OA from rotating clockwise about the pivot O. If the cable tension is 820…

Q: Determine the resultant of the four forces and one couple which act on the plate shown. 2 m 5 m 60 N…

Q: Determine the re forces about point Oof the F = 500 N 0.125 m, 0.3 m- 60 0.25 m F 600 N

Q: Determine the resultant of the four forces and one couple which act on the plate shown. 2 m -5 m 60…

Q: A force acts on a hook at point A as depicted. Determine in KN the component of this force which…

Q: Q22](problem 2/28i p37) (sāl2) Determine the resultant R' of the two forces Shown in fiqure, and…

A: Solution: Some of the forces in the horizontal direction is given by, ∑Fx=-…

Q: 2/121 A 50-lb force is applied to the control pedal as shown. The force lies in a plane parallel to…

Q: Current Attempt in Progress In checking a recently installed fencepost for adequacy of the ground…

A: To Find : The angle which P makes with the positive x axis and with x-z plane. Given : The…

Q: Q3- Resolve the 5200 N force into two components along u and v axis 5200 N 20 3/5 10 28 V

A: Given , Force , F =5200 N Angle of inclination of U and V axis with the vertical and the…

Q: Q3 - Vertical forces are applied to the handle of the pipe wrenches. Determine the moment that these…

A: Answer: The moment that these forces exert along the axis AB is 2 N•m (clock-wise).

Q: Replace the force system acting on the post by a resultant force. 0.5 m B, 500 N 1m 0.2 m 30 250 N…

Q: Q1: The 650 N tension force in cable AB is required to prevent the CA bar from rotating clockwise.…

Q: If the resultant of the forces shown passes through point A, determine the magnitude of the unknown…

A: Given: The loaded beam is shown below:

Q: The angle plate is subjected to the two 250-N forces shown. It is desired to replace these forces by…

Q: Q.3- If = 30°If and F1 = 250 lb, determine the magnitude of the resultant force act- ing on the…

Q: determine the distance x so that the resultant of the force system locate ?at the mid point of the…

A: For the given system To determine value of x if net resultant force passes through midpoint of…

Q: Replace the parallel force system acting on the plate by a resultant force ( kN ) and specify its…

Q: Q3/ Replace the two forces acting on the bent pipe by a single equivalent force R. Specify the…

Q: Replace the loading on the frame by a single resultant force. Specify where its line of action…

Q: Determine the x and y components of each of the forces shown. - 008- Dimensions in mm 800 N 600 424…

Q: Replace the loading by a single resultant force, specify the location of force measured from point…

Q: Q1: The 700 N tension force in cable AB is required to prevent the CA bar from rotating clockwise.…

A: Solution: The force can be resolved as Fx and Fy as shown in the figure (Fx and Fy are…

Q: Q1: The 800 N tension force in cable AB is required to prevent the CA bar from rotating clockwise.…

A: Draw the free body diagram. AD=1.5 msin 70°AD=1.41 m CD=1.5 mcos 70°CD=0.51 m…

Q: 2) Replace the force system acting on the post by a resultant force, and specify where its line of…

A: Apply the equilibrium of forces in the x-direction. Apply the equilibrium of forces in the…

Question

Replace the force system acting on a plate by a single force and determine where the line of
action of this force intersects the x-axis and the y-axis.
y
180 N
240 mm-
300 N
70°
15°
63 N.m
120 N
500 mm
60 N.m
180 mm
150 mm
-300 mm-
X
-600 mm-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q.V-Determine the magnitude of the resultant force acting on the bracket and its direction measured counterclockwise from the positive u axis. F = 150 lb 30 30 45° F = 200 lb
Q1/ Determine the magnitude and direction of the resultant force in system :below P1 = 10 KN P2 = 35 KN 8 = 750 82 = 45° P3 = 50 KN
Where does the resultant of the two forces act? Replace the two forces with a single equivalent force applied at a point on a horizontal line going through point A. Determine the distance d from point A. Your answer will be positive if to the right of A, negative if to the left. 660 N 370 mm 630 N 440 mm. Choices: 5.85 m OO -5.85 m 8.58 m -8.58 m
Solve for the resultant force. F4 F1 F3 1 m F2 125 m 125 m F1 = 602 N F2 = 107 N F3 = 105 N F4 = 382 N
7) An ergonomically designed key for a computer keyboard has an approximately flat surface defined by points A, B, and C and is subjected to a 1N force in the direction normal to the key's surface. The motion of the key is in the Z direction. Determine the components of the force in directions normal and tangent to the key's motion. B IN A (15,0, 10) mm B (0, 0, 15) mm C (0, 15, 12) mm C
Еxample's Replace the loading system by an equivalent resultant force and specify where the resultant's line of action intersects the member measured from A. 200 lb 50 Ib 30 3ft -3 ft -3ft 100 lb
Use the rectangular component method to solve the fol- lowing problems. Determine the magnitude R of the re- sultant of the forces and the angle 6, between the line of action of the resultant and the x-axis for F2 = 800 Ib 30 60° F1 = 300 lb 33 F- 750 Ib
Resolve each force acting on the post into its x and y components. F= 300 N F:= 450 N F= 600 N 45
2/87: Replace the three forces acting on the bent pipe by a single equivalent force R. Specify the distance x from point O to the point on the x-axis through which the line of action of R passes. Ans. R = 215.40N, x= 1.625 m 200 N 160 N 250 mm 250 mm -250 mm 125 mm 240 N
4. A machine component is subjected to the forces and couples as shown. If P = 60 N, determine the magnitude and direction of the resultant force as well as the location where the resultant force passes through vertical line GF and horizontal line GH. 15 200 N 50 mm 520 mm E 50 mm 240 mm 42 N-m D 120 N 70⁰ 40 N-m 640 mm H 80 N 180 mm B +50mm Ans: (a) 0.365 m above G (b) 0.227 m to the right of G
Find the resultant of the three forces acting on the square plate. 70 lb 10 lb 0.75 ft 0.75 ft 60 lb 6 ft 6 ft The wrench shown is the resultant of a force-couple system with the force acting at point 0. Determine the force and the couple of the original system. Use F = - 6i + 8j + 5k kNand C = - 18i + 24j + 15k kN • m. wwwwwm ww F 4 m 12 m 3 m
Q1: The 700 N tension force in cable AB is required to prevent the CA bar from rotating clockwise. Resolve this force in to two perpendicular components, along X and Y axes. DA 2 m 1.5 B 60 1.5 m