ReLaCs ka lang! A RLC series circuit has C= 5 x 10-3 [F], R = 100 [2], and L=3× 10-3 [H]. This circuit is connected to an AC supply that gives out 10 [V] at 600 [Hz]. Which of the following statements is true regarding the current and the voltage of the generator? O A. The source voltage lags the current. OB. The source voltage leads the current. OC. The current leads the source voltage. 29 O D. The source voltage and current are in phase.

ReLaCs ka lang! A RLC series circuit has C= 5 x 10-3 [F], R = 100 [2], and L=3× 10-3 [H]. This circuit is connected to an AC supply that gives out 10 [V] at 600 [Hz]. Which of the following statements is true regarding the current and the voltage of the generator? O A. The source voltage lags the current. OB. The source voltage leads the current. OC. The current leads the source voltage. 29 O D. The source voltage and current are in phase.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.25MCQ

See similar textbooks

Similar questions

The part of rotor resistance of a 3-phase induction motor which represents electrical equivalent of mechanical load on the motor is O R2 (1- 1/S) O R2 (1-S) O R2 O R2 (1/S -1)
QUESTION 3 An inductor, a capacitor, and a resistor are connected in parallel with a function generator. The inductor draws 100mA RMS, the capacitor draws 150mA RMS, and the resistor draws 200mA RMS. Find the magnitude of the total current. O 450mA RMS O 544mA RMS O 352mA RMS O 206mA RMS
1. Set up the circuit shown using a function generator for the source voltage Vs. Set the function generator to 10 V P-P at 100 Hz (You need to set the Vp-p on the function generator to 5V). Connect the red lead of the scope to VoUT and the black lead to the ground to measure the output or load voltage. 1N4004 Vout Vs 10Vpp 100HZ 1k Ohm 2. Sketch Vout on right, measure the exact peak voltage to the ground on the oscilloscope (use the oscilloscope). DC coupling setting of the 主 Note: Show the results on the screen to your professor to get the signature. V out (Peak) = Vout 3. What is the measured frequency of the load voltage waveform? Frequency f =
separately excited DC generator Rf m For a Rf = 1003 If Find LA Vt Ia Ef x!M off Pin Pout 0% eff T Ia anforce ratrc = 0.1552 Off 'f = 600 V = 1000 rpm Rood=502 n V
A synchronous generator generates 370 V at 55 Hz when the field current is 4.4A. The e.m.f generated when the frequency is 35HZ and the field current is 2.9A is ..... .......
False True The speed of d.c shunt motor is decreased if the field current is increased Wave windings are used in d.c machine designed for High voltage high current d-c generator The main disadvantage of series generators, Output voltage varies as the load varies
A synchronous generator generates 350 V at 55 Hz when the field current is 3.7A. The e.m.f generated when the frequency is 35Hz and the field current is 2.3A is ............... Answer
60. Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and a maximum negative amplitude of -5 V using a single 14 V de voltage source. 61 Datermine the volto in the girRuit F Figura 1 1?
The swept area of a wind turbine is 485 m. The diameter of the rotor is Select one: O a. 617.02 cm O b. 24.84 m O . 12.42 m O d. 22 m
X (23) WhatsApp x 4 Meet-hpd-sdbt-gho Xle-Chrome to slo 9 Google bilp YouTube web.whatsapp.com @ Gmal M Courje bl ulhi A synchronous machine is generating power of 2.7 MW, If the machine can deliver a maximum power of 3.1 MW. the power angle in radian is 0.85 O 0.72 O 0.51 O 1.06 a+T The value of armature current in the waveform is 14 A, a = 54 degrees, and B = 155 degrees. The RMS value of current is 70435O ProBook 4340s hp ENG 4
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
The complex volt amperes in a series circuit are (4300- j2500) and the current is (25 + j43.3)A.Find the applied voltage.