Reactants A and B are mixed in a beaker by Ethan. He waits for it to react completely. He knows that theoretically it will form a mixture that contains three products. Ethan needed only product E, so he separated the mixture by getting product C first, since it is a solid precipitate. Then he separated the two liquids by making use of their different boiling points to be able to get product E. Which order of separation techniques did Ethan use to get product E?

Reactants A and B are mixed in a beaker by Ethan. He waits for it to react completely. He knows that theoretically it will form a mixture that contains three products. Ethan needed only product E, so he separated the mixture by getting product C first, since it is a solid precipitate. Then he separated the two liquids by making use of their different boiling points to be able to get product E. Which order of separation techniques did Ethan use to get product E?

Chemistry: Matter and Change

1st Edition

ISBN:9780078746376

Author:Dinah Zike, Laurel Dingrando, Nicholas Hainen, Cheryl Wistrom

Publisher:Dinah Zike, Laurel Dingrando, Nicholas Hainen, Cheryl Wistrom

Chapter16: Reaction Rates

Section: Chapter Questions

Problem 51A: In general, what is the relationship between reaction rate and reactant concentration?

See similar textbooks

Similar questions

In this experiment, you will be running multiple trials, each with a TOTAL volume of 35 mL, but with an increasing the amount of vinegar in that mixture each time. What you think will happen as you go from trial 1 all the way through trial 8? The highest amount of NaHCO3 will react in trial #1. The highest amount of NaHCO3 will react in trial #8. The amount of NaHCO3 will react more and more with each trial until a certain point, at which it doesn't matter how much vinegar is added because all of the NaHCO3 will be used up. The amount of NaHCO3 will react less and less with each trial until a certain point, at which it doesn't matter how much vinegar is added because all of the vinegar will be used up.
In part 1 of this lab, you will be calculating A₁H by conducting constant-pressure calorimetry measurements. One of the final steps in this calculation is obtaining ArH by taking the q value (with respect to the system) and dividing by n. What number of moles (n) will you be using in the above formula? Select one: Number of moles of magnesium, since Mg is in the balanced chemical equation and is a part of the system Number of moles of water
7. A student weighs out exactly 1.562 grams of p-aminophenol and exactly 40 mL of water. After dissolving p-aminophenol in HCI, 10 mL of acetic anhydride is added. The student follows the procedure and acetaminophen is prepared. What is the maximum amount of acetaminophen she could obtain from the reaction if the percentage yield is 76%? I
doug began preparing laboratory surface disinfectant from chlorine bleach. he put on a chemical resistant apron and gloves and then removed the bleach container from the special chemical cabinet. he carefully placed the container on the laboratory benchtop and began to add the chlorine bleach to distilled water. nearby workers began complaining of burning eyes. doug was reprimanded by the supervisor. Explain why.
The molecular weight of acetanilide is 135.17 grams/mole. The solubility of acetanilide in water is 5.5 grams/100 mL at 100°C and 0.53 grams/100 mL at 0°C. You are given a 30.0 gram sample of acetanilide that has been contaminated with insoluble sawdust. For every 10.0 grams of sample, 1.5 grams of that sample is sawdust. Theoretically, if you use just enough water to dissolve the entire sample of acetanilide, how much acetanilide will crystallize upon cooling to 0°C? 25.5 grams 23.0 grams 105.2 grams 109.7 grams 2.5 grams
3. Assuming that concentrated hydrochloric acid (HCI) is 12.1 M and that the synthesis reaction has a 1:1 molar ratio of HCI to tert-butyl alcohol, determine the molar ratio of HCI to tert-butyl alcohol, if one used 5.43 g of tert-butyl alcohol and 15.0 mL of HCI. Show your calculations. Was tert-butyl alcohol or HCI the limiting reagent? Briefly explain.
What are Catalytic Converters?
Mg(NO3)2 H2SO4→ Ca(NO3)2 H2SO4→ Sr(NO3)2 + H2SO4 → Вa(NOз)2 + H2SO4 →
Classify each of these reactions. Reaction 2 NaOH(aq) + Pb(CIO3)₂(aq) - C₂H₂(g) + 30₂(g) - 2 AgNO3(aq) + Zn(s) HI(aq) + LiOH(aq) 2 NaC1O3(aq) + Pb(OH)₂ (s) 2 CO₂(g) + 2 H₂O(1) Zn(NO3)₂(aq) + 2 Ag(s) H₂O(1) + Lil(aq) redox Answer Bank acid-base neutralization Type precipitation
Name the products and reactants in this reaction
5. Suppose you have a mixture of water and your 2-chloro-2-methylbutane product in a separatory funnel. Use densities to predict which phase will be the top layer in the funnel. a. 2-chloro-2-methylbutane (organic phase) b. water (aqueous phase) c. there would only be one phase since the substances are miscible
Pounding is a usual technique used in sample preparation. What is the chemical basis why pounding is used in sample preparation? O Pounding allows molecules to be prepared for reaction Pounding breaks the intermolecular forces within molecules Pounding increases surface area leading to faster reaction Pounding allows samples to fit in test tube