R1R2AR5BR4R3R6R7The circuit above has R1 = 820 Q, R2 = 220 Q, R3 = 470 N, R4 = 910 Q, R5 = 560 Q,R6 = 330 Q, and R7 = 680 Q and an equivalent resistance looking into points A and Bof RAB = 2244.8 . The voltage applied to the circuit is VAB = 100 V. Determine thevoltage across R5.%3D= 18.49 VVR5Vr5 = 10.51 V%3DVR5= 30.29 VO Vr5 = 36.53 V

Answered: Image /qna-images/answer/825b6c18-78a5-4437-b314-e44b08f25c28.jpg

R1 R2 A R5 B R4 R3 R6 R7 The circuit above has R1 = 820 Q, R2 = 220 Q, R3 = 470 Q, R4 = 910 Q, R5 = 560 Q, R6 = 330 Q, and R7 = 680 Q and an equivalent resistance looking into points A and B of RAB = 2244.8 Q. The voltage applied to the circuit is VAB = 100 V. Determine the voltage across R5. VR5 = 18.49 V VR5 = 10.51 V Vr5 = 30.29 V O VR5 = 36.53 V %3D

R1 R2 A R5 B R4 R3 R6 R7 The circuit above has R1 = 820 Q, R2 = 220 Q, R3 = 470 Q, R4 = 910 Q, R5 = 560 Q, R6 = 330 Q, and R7 = 680 Q and an equivalent resistance looking into points A and B of RAB = 2244.8 Q. The voltage applied to the circuit is VAB = 100 V. Determine the voltage across R5. VR5 = 18.49 V VR5 = 10.51 V Vr5 = 30.29 V O VR5 = 36.53 V %3D

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

An ac resistance is higher than a dc resistance. True False
Which of the following statements are correct for the circuit below? Thanks to the capacitors I – C1 and C2, the voltage gain of the circuit increases. II – Capacitors C1 and C2 are coupling capacitors and provide an isolation function between AC and DC voltages in the circuit. Thanks to the III – RE resistor, the voltage gain of the circuit increases. Thanks to the IV – RE resistor, the stability of the circuit increases. The V – C3 Capacitor is a bypass capacitor and prevents the loss of voltage gain. Capacitor VI – C3 is a coupling capacitor and has no effect on the voltage gain in the circuit. VII – As the value of the source internal resistance Rs increases, the voltage gain decreases. VIII – The voltage gain decreases as the value of any RL load to be added to the circuit increases
Determine E and P3. Given R1 = 10ohms, R2 = 20ohms, R3 = 60 ohms, R4= 10ohms, R5= 20ohms, R6= 60ohms, R7= 10 ohms, R8= 20 ohms. R9= 30ohms, P6 = 540W.
the adjoining figure. This lamp can withstand a maximum voltage 3.0 v 0.4 9. Volt-ampere (V-I) charaeteristics of an incandescent lamp 16thd in and a maximum current 0.4 A. An infinite ladder network consisting a large number of these lamps is also shown in the figure given belo How much maximum voltage can be applied between the terminals A and B, so that no lamp gets damaged? (Use V5 = 2.2). Ans:x4.2V Hint: Curentin all bulls except first is
Series-Parallel Circuit For the following circuit, determine: a) The total resistance RT b) The current IRI c) The current Ir6. d) The power consumed by R6.. . Ri 15 Ry 30s 15L 15 Rz 12v 30s2
Given the circuit below and that R1=1.7ohm,R2=3.5ohm,Emf1=2.1V and Emf2=6.3V. What is the current through the section ac?
Find the voltage across each inductor for the given circuit using the voltage divider rule. VL1 +m= L₁=10mH Vs=100 V, 60 Hz VL2 +mm- L₂=14mH
6. The main difference between resistance R and capacitive reactance X, is that (a) Xc is the same for both DC and AC signals, where R depends on frequency of the AC signal (b) R is the same for both DC and AC signals, where X depends on the frequency of an AC signal (c) R is measured in ohms and X is measured in farads (d) None of the above
1 Ia = ?? A 2.ib= ?? A 3 Vx = ?? 4 power at Rx = ?? 5 power at Rb = ??
Which of the following statements is true of an open component in a series circuit? a.. The circuit current will be higher than normal. b. The voltage drop across the component will be lower than normal. c. The voltage drop across the component will be higher than normal. d, The resistance of the component will be lower than normal.
Determine the DC currents (la. lc and I) and dc junction voltages (Var Ver and Vca) la-Blank 1 mA, le-Blank 2 mA, I-Blank 3 mA, Var Blank 4 V, Vcr Blank 5 V and VcB - Blank 6 V Use 2 decimal places. Use the following values. VBB= 3V RB= 5kOhms Rc=232 ohms Vcc =18 V BDC=65
If a circuit has a resistance of 3002 and a series inductance of 5002, what is the relationship between the applied circuit voltage and the circuit current? The applied voltage lags the circuit current. The phase shift between the circuit voltage and current changes with time. The applied voltage is in phase with the circuit current. The applied voltage leads the circuit cur Previous Page Next Page Page 2 of 10