Questions A:1. What happen if you only touch one test probe of the voltmeter to one end ofa battery?2. How does the meter have to connect to the battery in order to provide anindication?

According to the question we have to discuss 1. What happens if you only touch one test probe of…

Answered: Questions A: 1. What happen if you only…

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter32: Standby Power Systems

Section: Chapter Questions

Problem 1R

See similar textbooks

Similar questions

What is the difference between an ammeter and a voltmeter? How they are connected in a circuit (draw circuit diagram)?
How does a voltmeter differ from a potentiometer? What type of meter is the Corning-10 pH meter?
Question 9 An analog voltmeter has 100 divisions on the scale. The voltage read is 6 volts and the meter has two ranges as 0 – 10 volts and 0-100 volts. Find the uncertainty in the measured value in both ranges. (Uncertainty = ±½ VFSD / # of divisions) Question 10 The following values obtained from the measurements of the values of 147.2,147.4,4,147.9,148.1,147.7,147.5,147.6,147.4,147.6 and 147.5. Calculate: The arithmetic mean The standard deviation
14. A 6-V lead-acid battery has an A-hr rating of 180 A-hr. The battery is to be load-tested. What should be the test current, and what are the maximum permissible amount and duration of the voltage drop?
What is the purpose of shunt resistors in an ammeter? A. To shorten the range of the ammeter. B. To shunt current around the meter movement. C. To shunt voltage around the meter movement. D. To limit current at the input of the ammeter.
how about on discharging how many volts is the maximum to discharge the battery?
In the electrical circuit of a house, the fuse acts as A) a load B) a thermopile C) a safety device D) a step down device
On separate sheets of bond paper, draw and write the uses of voltmeter and ammeter.
If the measured values for resistors #1, #2 and # 3 are 552, 549 and 549 Ohms calculate the %error (measured difference from expected value as a percentage) for each resistor. Are they within tolerance (or specification) of manufacturer? #1 98.4% #2 97.9% #3 97.9% Yes within specification a. b. #1 1.6% #2 2.1% #3 2.1% Yes within specification #1 1.6% #2 2.1% #3 2.1% No outside specification Ос. Use Ohm's Law to calculate the equivalent resistance of R12, R23 and R123 (as specified in the lab manual) using measured resistances #1 552 Ohms, #2 549 Ohms, #3 549 Ohms R, R2 R,= R12 R23
What is the formula used to find the peak voltage of 100 volts effective? A. Peak voltage = .707 x 100. B. Peak voltage = .9 x 100. C. Peak voltage = 1.414 x 100. D. None of the above.
7. How does the multimeter/voltmeter have to connect to the battery in order to provide an indication? What does this tell us about multimeter/voltmeter use and the nature of voltage? 8. Is there such a thing as voltage "at" a single point? 9. What would you say about a piece of wire if the ohmmeter needle didn't move at all when the probes were connected to opposite ends?
15 V Electronic circuit "Ground" 15 V B Determine what a digital voltmeter would indicate if connected between the following points: a) Red lead on Ä", black lead on ground b) Red lead on "B", black lead on ground c) Red lead on Ä", black lead on "B" d) Red lead on “B", black lead on Ä"

SEE MORE QUESTIONS

Recommended textbooks for you

EBK ELECTRICAL WIRING RESIDENTIAL

Electrical Engineering

ISBN:

9781337516549

Author:

Simmons

Publisher:

CENGAGE LEARNING - CONSIGNMENT

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

EBK ELECTRICAL WIRING RESIDENTIAL

Electrical Engineering

ISBN:

9781337516549

Author:

Simmons

Publisher:

CENGAGE LEARNING - CONSIGNMENT

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Questions A: 1. What happen if you only touch one test probe of the voltmeter to one end of a battery? 2. How does the meter have to connect to the battery in order to provide an indication?