Question.In a series inverter for the operating frequency range of 1KHZ-8KH2 and the loadresistance of 50-100 ohm, the peak load current is limited to 4 A and the supply voltage is125 V where attenuation factor is given as 0.5 then what are the inductance andcapacitance values anre?Option 1:7.25 mH, 0.12 µFOption 2:1.25 mH, 0.14 µFOption 3:2.25 mH, 0.12 µFOption 4:2.25 mH, 0.14 µF

Option 4 Is the correct answer L=2.25mH C=0.14uf

Question In a series inverter for the operating frequency range of 1KHZ- BKHZ and the load resistance of 50-100 ohm, the peak load current is limited to 4 A and the supply oltage is 125 V where attenuation factor is given as 0.5 then what are the inductance and capacitance values are? Option 1: 7.25 mH, 0.12 uF Option 2: 1.25 mH, 0.14 µF Option 3: 2.25 mH, 0.12 µF Option 4: 2.25 mH, 0.14 µF

Question In a series inverter for the operating frequency range of 1KHZ- BKHZ and the load resistance of 50-100 ohm, the peak load current is limited to 4 A and the supply oltage is 125 V where attenuation factor is given as 0.5 then what are the inductance and capacitance values are? Option 1: 7.25 mH, 0.12 uF Option 2: 1.25 mH, 0.14 µF Option 3: 2.25 mH, 0.12 µF Option 4: 2.25 mH, 0.14 µF

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A HVDC link is operating with 175 KV AC line voltage at the rectifier. When the DC current is 1100 Amps, the rectifier delay angle is 100 and inverter extinction angle is 200. The resistance of the line is 23 ohms and the commutating reactances of the rectifier and inverter are 22 ohms and 21 ohms. Calculate the DC voltages at the rectifier and inverter terminals and the AC line voltage at the inverter.
In the VI characteristics of JFET When Vgs=0, 1..When we increases the Vds,Id is also increases.(width of deplation region cannot change ) In this case Vds and Id are proportional by ohms law. This is ohmic region 2.. but after a perticular pt. (Pich off voltage)When Vgs Is zero. Id=Idss and is constant (as Vds goes on Increasing Vgd set such width off deplation region to Id become constant) This is active region of JFET 3 but on further Increasing Vds , Id starts suddenly increase (breack down condition) What reason this should happen?
Q2 (a) Figure Q2(a) shows a single-phase full-bridge square-wave voltage source inverter has resistor (R) and inductor (L) load of 10 Q and 5 mH respectively connected in series. The inverter output frequency is 50 Hz. The transistor switching scheme is complementary bipolar. (i) Draw the output voltage and current waveforms. (ii) Obtain an expression of the rms output voltage at the fundamental frequency. (iii) If the fundamental AC output voltage is 220 V, find the required DC input voltage for the inverter. (iv) Find the instantaneos load current by considering until the 9th harmonics number. (v) Calculate the total harmonics distortion (THD) of the load current. Use only the first three odd harmonics. (vi) Sketch the harmonics spectrum for output current. (vii) Show the displacement angle a, if 5th harmonic is to be eliminated.
2. We discussed in class how the channel capacitance can be modeled in different region of operations in MOSFETs. For your reference, the slide is shown below. Explain how you think the model would look like if a transistor is in velocity saturation region? Channel Capacitances Channel capacitance is a voltage dependent and non-linear capacitance S C P-sub Bulk Cutoff Region D Operation Region Cutoff Linear Saturation S P-sub Bulk C Linear Region CGBCH CoxWLeff 0 0 1 2 3 S P-sub Bulk Saturation Region CGSCH 0 сат CoxWL eff 1 2 CGDCH 0 CoxWLoft CoxWLoff eff D 0
Question 2 a) Briefly explain the de chopper, inverter, controlled rectifier and ac voltage controller. b) A buck-boost regulator as shown in Figure 2 has an input voltage, Vs = 12 V. The duty cycle, k = 0.35 and the switching frequency is 30 kHz. It also has an inductance, L = 200 µH, filter capacitance, C = 440 µF. The average load current, Ia 1.25 A. Determine the: i. average output voltage, Va, ii. peak-to-peak output ripple voltage, AVc, iii. peak-to-peak output ripple current of inductor, AI, iv. peak current of the transistor, Ip, V. critical values of L and C, and vi. critical values of L and C if Vs is increased to 14 V. Estimate the change in percentage for the critical values of L and C. is Vs C Load Vo, Vs VC i, Ia Figure 2
In a single phase VSI bridge Inverter, the load current is Io =200 sin(wt-45°)mA. The d.c. supply voltage is 220 V. What is the power drawn from the supply ?
The mode of operation for the D-MOSFET is Select one: a. the ohmic region only b. the enhancement mode only c. both the depletion and enhancement modes d. the depletion mode only
FET: Plot the plot the AC & DC load line and Find the Q point. IDSS = 5 mA VGSOFF = - 5V
• In MOSFET, it is the foundation upon which the device will be constructed and is formed from a silicon base A. Substrate, B. Slab, C. Source, D. Base.
VoO for Ma mosfet Nn Cox ( )= Jm Alv? ,Vrw=0,7V J00NA (+) VX %3D %3D a) In uhat condition does the mosfet work ?and frnd the voltage Vx= ? M1 3V b) what is the mompmum Voo voltage and why'?
Investigate the operation principle of 3- phase inverter for 120°-Δ conduction interval (by sketching phase-to-phase and phase-to-neutral voltages and terminal currents).
iv. For six-phase half-wave rectifier circuit, the preferred circuit from the point of harmonics reduction in the supply currents is: (a) Simple six-phase half-wave circuit. (b)Double-star six-phase half-wave circuit. (c) Six-phase fork connection circuit. v. The DC supply of single phase bridge inverter is 350V. For quasi-square wave output voltage with a 70 percent ON time and frequency is 50HZ, the RMS value of output voltage is: (a) 292.8V (b) 220.5V (c) 250.6V