Question: A group of Students from UTAS (Physics Unit) visit Al Hassan Electrical laboratory. Their supervisor gives them instruction about use of Resistors in different electrical appliances. Students are provided with four resistors R1=50 ohm, R2=70 ohm, R3=380 ohm, R4=70 ohm and a battery of 40 v. i) If students connect these four resistances in series, what is the effective resistance? ii) If students connect these four resistances in parallel, what is the effective resistance? iii) If students connect 40 V battery across series combination, what is the current flowing in the circuit? iv) If students connect 40 V battery across parallel combination, what is the current flowing in the circuit? v) If students connect these four resistances as shown below, what is the voltage across points a and d? R2 R1 R4 R3

Question: A group of Students from UTAS (Physics Unit) visit Al Hassan Electrical laboratory. Their supervisor gives them instruction about use of Resistors in different electrical appliances. Students are provided with four resistors R1=50 ohm, R2=70 ohm, R3=380 ohm, R4=70 ohm and a battery of 40 v. i) If students connect these four resistances in series, what is the effective resistance? ii) If students connect these four resistances in parallel, what is the effective resistance? iii) If students connect 40 V battery across series combination, what is the current flowing in the circuit? iv) If students connect 40 V battery across parallel combination, what is the current flowing in the circuit? v) If students connect these four resistances as shown below, what is the voltage across points a and d? R2 R1 R4 R3

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Similar questions

In the figure on the right, the ideal batteries have emfs &1= 10 V and 82 = 83 = 6 V and the resistors are identical with R = 5 ohm. (a) independent eqaations to solve three unknown currents i, iz, and i; as shown in the figure and solve for the current i. That is, what is the magnitude and direction of iz? (b) (c) (d) batteries are equal to the total power loss in all the resistors. RI i ww. Apply Kirchhoffs loop and junction rules and obtain three El R3 R, 83 What is the magnitude and direction of iz? What is the total energy dissipation rate in all the resistors Prove that total power supplied to the circuit by the ww wwH
FACTS: AC-DC converters take the AC power from wall outlets and convert it to unregulated DC. These power supplies include transformers that change the voltage of the AC that comes through wall outlets, rectifiers to save it from AC to DC and a filter that removes noise from the peaks and troths of the AC power waves.The DC-to-AC Converters are used to charge the batteries in the vehicles. These circuits are mainly used for driving low-power AC motors and are used in a solar power system. The DC to AC converters can be used in dc transmission lines for transmitting power to loads. QUESTION: What do you think is the main reason why we have AC power in our outlets instead of DC power? Explain your answer.
Problem No.2 group Six group of batteries are in parallel. Each has 10 cells connected in series, each has an internal emf of GV and resistance fo 0.412. a. Determine the equivalent emf and the internal resistance of the battery system.. b. If a 1-kn load resistor is connected to the battery system, what is the power dissipated to this load venistor? c. In & hre operation, determine the total energy delivered source to the 1-ks load resistor. the by
Exe: The single-phase bridge rectifier has an RL Load and an ac source, with R = 10Ω andL = 10mH. The peak value of the source is Vm = 100V at 60 Hz. The expressions of voltage andcurrent outputs are:(a) Determine v0(t) and i0(t) with two ac terms (n=2 and 4)(b) Determine the power absorbed by the load.
Basic Electrical EngineeringDraw symbols of electrical components. Note: You may use both IEC and NEMA symbols. - Conductors crossing but not connected- Conductors crossing and connected - DC source other than battery- DC generator- AC voltage source- Ideal current source- Ideal Voltage Source- Current Controlled Current Source- Current Controlled Voltage Source- Voltage Controlled Current Source - Voltage Controlled Voltage Source
ESSAY. Explain in your own words and discuss the significance One of the most important parameters for semiconductor components is the power rating. Explain why power rating is such a critical parameter, especially compared with other types of electronic components (resistors, inductors, capacitors, etc.).
4- Can value of the string efficiency being equal to 100%. Explain your answer.5- Outline methods used to equalize the potential across the units.6- Why an insulator is represented as a capacitor C? What are the assumptionmodes?
Ferrule has to be connected and ………….. in order to connect 2 underground cables
An inductance of L henrys and a resistance of 10 ohms are connected in series withvoltage of 100 Volts. If the current is initially zero, and is equal to 9 Amperes after 1second.a) Find L? and b) Find the current after 0.5 s.
An aluminum wire 7.5 m long is connected in parallel with a copper wire 6 m long. When a current of 5 A is passed through the combination it is found that the current in aluminum wire is 3 A. The diameter of aluminum wire is 1 mm. Determine the diameter of the copper wire. Resistivity of copper is 1.7 x 10 “ ohm-cm and that of aluminum is 1.724 micro-ohm-cm.
Magnetically coupled circuit example
Determine the current Ic, current at the resistor, and current supplied by the voltage source. Note: you must put the imaginary part of the reactances and its sign