Question 7 A precision metal part needs to be manufactured using a casting process. The part needs to be made from a high melting point alloy, should have high dimensional accuracy, and weighs less than 2 Kg. Which process would you recommend and why? To support your answer you can compare your chosen process against other casting processes.

Question 7 A precision metal part needs to be manufactured using a casting process. The part needs to be made from a high melting point alloy, should have high dimensional accuracy, and weighs less than 2 Kg. Which process would you recommend and why? To support your answer you can compare your chosen process against other casting processes.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QUESTION 14 Pieces thicker than 5.45mm are considered sheet. O True O False QUESTION 15 In sand casting, natural sands are less economical than synthetic sands. O True O False QUESTION 16 Typical sheet-metal thicknesses are between 0.15 mm and 7 mm. O True False
2.1 What is the benefit of using investment casting for the production of a turbine rotorcompared to other casting processes?2.2 Which AM materials and processes (according to the ISO/ASTM 52900 standard) ismostly used during the manufacturing of patterns for the investment casting process?List the advantages and disadvantages of each of the AM processes.2.3 What are the advantages and disadvantages of using AM techniques to producepatterns for the investment casting process, compared to conventional methods?2.4 Show with a sketch, how the build orientation of the processes listed in Question 2.2can have an influence on the accuracy and surface quality of a pattern.2.5 Which manufacturing process (listed in Question 2.2) will be most suitable to producea pattern for the turbine rotor? Provide reasons for your selection.2.6 The use of additive manufactured patterns for the investment casting process arebeing used more frequently in industry. Using this technology, comment onproduction…
The below product in Figure Q1 requires to be sand casted based on the dimensions given. The past records revealed that a cylinder with a diameter of 1.5m with a height of 3m solidifies in 3 minutes in a sand casting operation using a similar material. a) Calculate the process time required for this design below. b) Suggest a suitable design of the riser. Specify what would be the riser dimension be in order to cater for this design. Justify your answer for the minimum possible size. c) Sketch a cross sectional drawing of the casting process with proper labeling of all the critical parts and suggest how would you modify the casting process if the cylinder part below required to be hollow instead of fully solid. r= 8 cm h = 60 cm 24 cm h = 220 cm Figure Ql
Q1. Draw and explain five casting defects in sand casting process.
A grey cast iron block of dimension 200 mm × 100 mm × 10 mm is produced by sand casting . Pattern making allowance is 10 %. What is the ratio of volume of the parttern to volume of the casting.
For the casting of the part whose perspective pictures are given below, take into account the surface of the section, the model design, if necessary, the core design, all the molding stages and finally, draw the mold in the most suitable form for casting and name all the mold elements by showing them on the figure (Note: The hole shown in the figure is a full hole. .)
Q1. Draw and explain five casting defects in sand casting process. briefly.
In green-sand casting, tolerances and surface finish are better than other casting processes. Select one: O True O False
Q1.Write down your answer briefly. i) Why is the permeability of shell mold higher as compared to sand mold? ii)What type of die casting process is mostly preferable for higher production rate? Justify your answer. iii) Bauschinger effect can be reduced by the stress aging process. Justify your answer. iv) Why is the sand for foundry practice called green sand? Can it be used for the core making process? v) What is moldability? How do you determine moldability of molding sand? vi) Which casting process is usually preferred for producing long tubular objects? Is it possible to manufacture a solid and parallelepiped object having different dimensions in a centrifugal casting process? Justify your answer. vii) What is directional solidification? How does a riser promote directional solidification?
4. Briefly describe die casting process and name 2 types.
‏Q1 . Draw and explain five casting defects in sand casting process . Q2 . Explain hot working process with respect to microstructure . Also draw the diagram of microstructure.
2. Assignment You are tasked to investigate the following and to compile your findings in a technical report: 2.1 What is the benefit of using investment casting for the production of a turbine rotor compared to other casting processes? 2.2 Which AM materials and processes (according to the ISO/ASTM 52900 standard) is mostly used during the manufacturing of patterns for the investment casting process? List the advantages and disadvantages of each of the AM processes. 2.3 What are the advantages and disadvantages of using AM techniques to produce patterns for the investment casting process, compared to conventional methods? 2.4 Show with a sketch, how the build orientation of the processes listed in Question 2.2 can have an influence on the accuracy and surface quality of a pattern. 2.5 Which manufacturing process (listed in Question 2.2) will be most suitable to produce a pattern for the turbine rotor? Provide reasons for your selection. 2.6 The use of additive manufactured patterns…