B ot general use from particular areas of theNomenclature.Question 6Classify the following parts, giving reasons for your answers:(a) A speed indicator for a motor vehicle.(b) A metal reinforced rubber conveyor belt.(c) A set of drumsticks that are imported with a base drum.(d) A sail for a yacht.(e) A plastic cover for an illuminated sign plate.() A pair of hinges for a pair of spectacles.(g) A textile sleeve for a men's woven coat.(h) A steel registration plate for a motor vehicle.)A drawer for an office metal filing cabinet.U) A spark plug for a motor vehicle engine.(k) A copper spring that is used to sedure a battery within a portable flashlight.(1) A gas compressor for a refrigerator.18:13

**As per our company we are supposed to do only 3 sub part if you need the rest please upload that…

Question 6 Classify the following parts, giving reasons for your answers: (a) A speed indicator for a motor vehicle. (b) A metal reinforced rubber conveyor belt. (c) A set of drumsticks that are imported with a base drum. (d) A sail for a yacht.

Question 6 Classify the following parts, giving reasons for your answers: (a) A speed indicator for a motor vehicle. (b) A metal reinforced rubber conveyor belt. (c) A set of drumsticks that are imported with a base drum. (d) A sail for a yacht.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Answer the two connected questions (Task A-1 and A-2). Provided in the last part are the guides and examples: The process for large-scale manufacture of paper has been largely unchanged for the last 125 years. The pulp and paper industry today is highly capital intensive, and there is an ongoing drive towards process integration, thereby increasing the efficiency of utilization of available process resources. This paper deals with the Kraft process (see Fig. 1) though the general principles described can be extended to other pulping processes. As shown in Figure 1, five water sinks and four water sources are considered for in-plant water reuse/ recycle. Prior to water reuse/ recycle, the network requires a freshwater flow rate of 36,400 tonne/day and generates 37,186 tonne/day of wastewater (sum of the individual sink and source flow rates in Table 1). The freshwater source that is available for service has an impurity concentration (chloride content) of 4.2 ppm, which is higher than…
Quality engineering question: What performance quality tests do we need to manufacture a patient turning apparatus shown in the picture? In addition to the product in the figure, belts to keep the legs stable and heating pads will be added to the product, write the necessary performance tests and briefly give information about these tests. (example of performance tests: ISO 10993-10, ISO 10993-5, etc.)
Write a brief report detailing the development of safety belts in cars. When was the first safety belt designed? Which was the first car manufacturer to incorporate safety belts as standard items in its cars? Write between ½ to 1-page report and make sure it is in your own words. Also, list your references using the Automatic Referencing & Citation with MSWord in IEEE style.
I posted it before but answer was wrong plz explain in detail
Assignment Booklet 4B ce 24: Module 4 6 Identify the safety features shown in this automobile from the following list. Place your answers in the blank spaces given. • bumper • hood • crumple zones • roll cage • side-impact beams Return to page 75 of the Student Module Booklet and begin Lesson 2. For questions 7 to 10, read each question carefully. Decide which of the choices BEST completes the statement or answers the question. Place your answer in the blank space given. 7. According to Transport Canada, how many Canadians owe their lives to seat belts between 1990 and 2000? A. 690 В. 1690 С. 1960 D. 11 690 8. By what percent is the webbing of a seat belt designed to stretch to help absorb energy in a collision? A. 0% B. 5-10% C. 10-15% D. 15-20% 9. What is the level of seat belt use in Alberta? A. 90% В. 70% С. 50% D. 30% Teacher
could u give me a brief explanation on how to read the table of r134A as well?
Jncct or pupci. 1. What is your mechanical advantage if you are using a 35 cm wrench on a bolt that has a diameter of 3 cm?
Show all working explaining detailly each step Answer must be typewritten with a computer keyboard! Answer Q7i, ii
Show all working explaining detailly each step Answer must be typewritten with a computer keyboard! Answer Qi, ii
I have three parts that need to be answered pertaining to the print provided below. With respect to the part of subassembly 1 that attaches to subassembly 2, which word bestdescribes the shape of the material at the connection: round tube, hexagon tube, squaretube. (Multiple Choice)A: round tubeB: hexagon tubeC: square The top assembly featured in this drawing appears to have two tall stems, each about 14.5″tall. What relationship exists between the two axes of the stems? (Multiple Choice)A: PerpendicularB: ParallelC: AngledD: X shaped When looking at Section A-A, how does the print reader know that this is several parts or pieces and not just one part? (Multiple Choice)A: Section lines are at different anglesB: The title block has the European symbolC: There's a general note that reads 'section shows more than one part'D: The reader must assume its several parts
Plzz solve this it's urgent
Summary/Conclusion Discuss the strengths of your design and how it met the specifications. Discuss your assumptions and why they are valid. Discuss what you might change about your design in a redesign effort. Format: The project should be presented as a design report using a word processor. Include any hand calculations in an appendix. More details will be provided. Choose to design either a slip-jaw or channel-lock pliers to last for 25 years of use by a professional. Use an appropriate tool steel for the pliers. Design for 95% male grip force. Use a minimum factory of safety of 2.50. Determine dimensions not given. Slip Jaw Pliers A= 9.00 inches B=1.00 inches C= ? D=1.25 inches H= 1.875 Inches D B A