Question 4. The following data are available from orthogonal cutting experiments. The depth ofcut (feed) to = 0.13 mm, width of cut b = 2.5 mm, rake angle a = - 5°, and cutting speed V = 2m/s.Chip thickness, t. (mm) = 0.23Cutting force, F. (N) = 430Thrust force, F; (N) = 280Determine the shear angle ð, friction coefficient u , shear stress t, shear strain y on the shearplane, chip velocity Ve, and shear velocity Vs, as well as energies uf ,Ug, and u

When the cutting edge is perpendicular to the machined surface, the cutting executed is termed…

Question 4. The following data are available from orthogonal cutting experiments. The depth of cut (feed) to = 0.13 mm, width of cut b = 2.5 mm, rake angle a = - 5°, and cutting speed V = 2 m/s. Chip thickness, te (mm) = 0.23 Cutting force, F. (N) = 430 Thrust force, F; (N) = 280 Determine the shear angle O, friction coefficient µ , shear stress t , shear strain y on the shear plane, chip velocity Ve, and shear velocity Vs, as well as energies uf ,us, and u

Question 4. The following data are available from orthogonal cutting experiments. The depth of cut (feed) to = 0.13 mm, width of cut b = 2.5 mm, rake angle a = - 5°, and cutting speed V = 2 m/s. Chip thickness, te (mm) = 0.23 Cutting force, F. (N) = 430 Thrust force, F; (N) = 280 Determine the shear angle O, friction coefficient µ , shear stress t , shear strain y on the shear plane, chip velocity Ve, and shear velocity Vs, as well as energies uf ,us, and u

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The following data was obtained from an orthogonal cutting test. Rake angle = 20° Depth of cut = 6 mm Feed rate = 0.25 mm/rev Cutting speed = 0.6 m/s Chip length before cutting = 29.4 mm Vertical cutting force = 1050 N Horizontal cutting force = 630 N Chip length after cutting = 12.9 mm Using Merchant's analysis, calculate (a) Magnitude of resultant force, (b) shear plane angle, (c) friction force and friction angle, and (d) various energies consumed.
A cylindrical mild steel work piece of Ø55 X 200mm undergoes a turning operation on a lathe machine to reduce the diameter to Ø 45mm. The cutting parameters are 23 m/minute, 0.3 mm/ revolution and 0.5 mm are cutting speed, feed and depth of cut respectively. Determine the following. i) Time for single pass (minutes). ii) Find number of passes required to reduce the diameter from Ø55 to Ø45mm. iii) Total time required to complete the turning operation in minutes (Tfinal).
3) The following data are available from orthogonal cutting experiment, Depth of cut t, = 0.13 mm, width of cut w = 2.5 mm, rake angle a = -5°, cutting speed v = 2 m/s, Chip thickness, t= 0.23 mm, cutting force, F. = 430 N, thrust force, F = 280 N. Determine the following: Shear angle Friction Coefficient u (using F= µ N) Shear Stress t,S Shear strain y on the shear plane. Power required to perform the operation. Gross power required if the efficiency of the machine is 85%. Specific Energy, Ut
.cutting speed is 9m/min. The return time to cutting time is 1:4 and the feed is 3mm Q.4 (i) Find the time required for taking a cemplete cut on a plate 600 × 900 mm", if the cutting speed is 9m/min. The return time to cutting time is 1:4 and the feed is 3mm for the shaper. The clearance at each end is 75 mm. (11) A hole of 30 mm diameter and 75 mm depth is to be drilled. The feed is 1.3 mm/rev and the cutting speed is 62 m/min. Assuming tool approach and tool over travel as 6 mm. Calculate : (a) Cutting time and (b) Material removal rate Q.5 Write short note on the following - (i) Up milling and down milling processes (ii) Balancing of grinding wheels (iii) Gear hobbing ittp3.7 w w w.ItuommC.com
Q24. For the below figure please write its part program. The depth of the cut is 0.25 inches (Finishing operation), while the tool's diameter is 0.5 inches. Consider the speed and feed. -0.75- - - 1.0 60⁰ RO.25 (0, 0) 0.75-
A cylindrical workpiece has a 14.0 in diameter and has 30 in long. It is to be turned in an engine lathe at the following cutting conditions: cutting speed = 400 ft/min, feed = 0.015 in/rev, and depth of cut = 0.150 in. Determine the time to complete one turning pass if the approach and overtravel allowances are each 0.25 in (total = 0.50 in). Note: 1 ft = 12 in
In a turning operation, cutting speed =200 m/min; feed = 0.25mm mm/rev, and depth of cut = 4.00mm Thermal diffusivity of the work material = 20m mm^2/s and volumetric specific heat =3.5(10^ -3 )J/mm^ 3 -C If the temperature increase above ambient temperature (20degreesC) is the angle measured by a tool-chip thermocouple to be 700degreesC, determine the specific energy for the work material in this operation.
A mild steel specimen of Initial diameter of 51.5 mm is turned to final diameter of 48 mm for an initial length of 151 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.1 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 7 mm, over run length is 2mm (iii) Total time required to complete the turning operation is 48.8 minutes (a) Find number of passes to finish the entire turning operation (b) The actual length of the turning operation in mm ( (c)The time required to complete one single turning operation in minutes (d) Spindle speed in rpm
Question 3. State whether or not the following statements are true, explaining your reasons: 3.a. For the same shear angle, there are two rake angles that give the same cutting ratio, 3.b. For the same depth of cut and rake angle, the type of cutting fluid used has no influence on chip thickness, 3.c. If the cutting speed, shear angle, and rake angle are known, the chip velocity can be calculated, 3.d. The chip becomes thinner as the rake angle increases, 3.e. The function of a chip breaker is to decrease the curvature of the chip.
A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Total time required to complete the turning operation is 59.6 minutes (a) Find number of passes to finish the entire turning operation ( (b) The actual length of the turning operation in mm ('
operation, the shear IS cIose to, In turning operation, spindle speed is set to provide a cutting speed of 2.2 m/: The feed and depth of cut are 0.32 mm and 2.1 mm, respectively. The tool rake angle is 15°. After the cut, the deformed chip thickness is measured to be 0.43 mm. Using the Orthogonal model as an approximation of turning operation, the shear strain is close to, In turning operation, spindle speed is set to provide a cutting speed of 2.4 m/
A mild steel specimen of Initial diameter of 30.5 mm is turned to final diameter of 27 mm for an initial length of 153 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Time required to complete one single turning operation is 3.5 minutes (a)Find number of passes to finish the entire turning operation (b) Total time required to complete the turning operation in minutes