Question 4 (Mapped to ILO1) A power generating plant consists of two turbo-alternator units whose fuel cost functions (F1 an F2) are expressed in £/hour as: F1= 0.04P1?+ 16 P1+ 500 F2 = 0.045P22 + 12P2 + 400 where P1 and P2 are the output power in MW of units 1 and 2, respectively. The two generating units are running continuously to meet a total plant load of 200 MW. For economic load dispatch, find the incremental fuel cost of the plant 2 in £/MWh and the require output of each unit.

Question 4 (Mapped to ILO1) A power generating plant consists of two turbo-alternator units whose fuel cost functions (F1 an F2) are expressed in £/hour as: F1= 0.04P1?+ 16 P1+ 500 F2 = 0.045P22 + 12P2 + 400 where P1 and P2 are the output power in MW of units 1 and 2, respectively. The two generating units are running continuously to meet a total plant load of 200 MW. For economic load dispatch, find the incremental fuel cost of the plant 2 in £/MWh and the require output of each unit.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Two 50-MVA, 3-phase alternators operate in parallel. The settings of the governors are such that the rise in speed from full-load to no-load is 2 percent in one machine and 3 percent in the other, the characteristics being straight lines in both cases. If each machine is fully loaded when the total load is 100 MW, what would be the load on each machine when the total load is 60 MW? (Req'd) Draw an appropriate diagram.
A Single Area consists of 3 generating units (G1/G2/G3) with the following characteristics: G1: 425 MVA rating, R1 = 0.015 pu (on the 425 MVA base), initial output P1 = 300 MW. G2: 300 MVA rating, R2 = 0.02 pu (on the 300 MVA base), initial output P2 = 200 MW. G3: 300 MVA rating, R3 = 0.03 pu (on the 300 MVA base), initial output P3 = 200 MW. The frequency of the system is 60 Hz. Assuming D = 0 pu and using a common base of 1000 MVA, what is the new steady-state frequency for a load increase of 100 MW? Select one: O a. None of these O b. 59.96 Hz O c. 58.75 Hz O d. 59.88 Hz
A Single Area consists of 3 generating units (G1/G2/G3) with the following characteristics: G1: 200 MVA rating, R1 = 0.025 pu (on the 200 MVA base), initial output P1 = 150 MW. G2: 300 MVA rating, R2 = 0.01 pu (on the 300 MVA base), initial output P2 = 200 MW. G3: 400 MVA rating, R3 = 0.02 pu (on the 400 MVA base), initial output P3 = 300 MW. The frequency of the system is 60 Hz. Assuming D 0.75 pu on a common base of 1000 MVA, what is the new generation output for G1 for a load increase of 150 MW? Select one: a. 252.12 MW b. None of these 170.42 MW d. 155.45 MW
OR e) Explain the following protection schemes of alternators. i) Stator inter turn protection. ii) Merz price protection.
A Single Area consists of 3 generating units (G1/G2/G3) with the following characteristics: G1: 200 MVA rating, R1 = 0.025 pu (on the 200 MVA base), initial output P1 = 150 MW. G2: 300 MVA rating, R2 = 0.01 pu (on the 300 MVA base), initial output P2 = 200 MW. G3: 400 MVA rating, R3 = 0.02 pu (on the 400 MVA base), initial output P3 = 300 MW. The frequency of the system is 60 Hz. Assuming D = 0.75 pu on a common base of 1000 MVA, what is the new generation output for G1 for a load increase of 150 MW? Select one: O a. None of these O b. 252.12 MW O c. 155.45 MW O d. 170.42 MW
Figure below shows a power system. The rating of generators and transformers are:G1:25MVA, 6.6KV, jO.2 p.u. G2:15MVA, 6.6KV, jo.15 p.u. G3:30MVA, 13.2KV, jo.15 p.u. T1: 30MVA, 6.6A- 115Y KV, jo.1 p.u.T2: 15MVA, 6.6A- 115Y KV, jo.1 p.u. T3:single phase units each rated 10MVA, 69/ 6.9 KV, jo.1 p.u. Find te reactances in p.u, take a base of 30MVA, 6.6 KV in the circuit of G1 .=.XG1 G2} 4 A lubu T2 T1 T3 G1 G3 j120 2 j90 N
e = 0 Q1: What does happen if we change two currents? a. Q2: What does happen if we have a three-phase four poles machine? Q3: What does happen if we have a two-phase two poles machine? e = 0 Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali Ki. pw --
15 Two generators having X1= 0.2 P1-60, and ) 2= 0.3P+40. If P1 = 150 and P2 250 MW. What is the economic loading of each generatorithe load is 250 MW Where: 50 EP2 < 250* P = 1015 N N PP 139 84 NW P1= 100 MW P7 = 1FO MW P. = 136. 84 MW PP = 11O16 MW| P1 = 17 MW.P = 150 M
b) A1000 MW turbine generated 648 MWh during 30 day. What would is capacity factor be?
A generator operating at 50 Hz delivers 1 pu power to an infinite bus through a transmission circuit in which resistance is ignored. A fault takes place. reducing the maximum power transferable to 0.5 pu whereas before the fault, this power was 2.0 pu and after the clearance of the fault, it is 1.5 pu. By the use of equal area criterion, determine the critical clearing angle.
Q3: Suggest operation schedule for the machines selected from suitable generator units from the 20,000, 25,000, 30,000 kVA and determine the load factor From a generating station has a flowing daily load cycle Time in hours Midnight -10 Region A in kW 10-12 40 12-17 65 17-20 20-22 30 22-midnight 60 20
1. If the number of poles in a lap wound generator is doubled, then the generated emf will be a) double c) constant d) zero b) half