Question 2 Refer to Figure 2 below. If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.06 m³/s is to occur in the cast-iron pipe (ks = 0.26 mm)? The kinematic viscosity of water at 10°C = 1.3×10-6 m²/s. Ignore all minor headlosses. Elevation = ? Water T=10°C Elevation = 110 mp B L=150 m D = 15 cm Cast-iron pipe L=100 m, D = 20 cm, cast-iron pipe Figure 2

Question 2 Refer to Figure 2 below. If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.06 m³/s is to occur in the cast-iron pipe (ks = 0.26 mm)? The kinematic viscosity of water at 10°C = 1.3×10-6 m²/s. Ignore all minor headlosses. Elevation = ? Water T=10°C Elevation = 110 mp B L=150 m D = 15 cm Cast-iron pipe L=100 m, D = 20 cm, cast-iron pipe Figure 2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q2] Water flows in a rectangular channel at a depth of 1.5 m. A 30 cm in height smooth hump produses a drop of 15 cm in the water surface elevation. Neglect losses and calculate the discharge per unit width of the channel. Energy line E₁ Y₁ 0.15 m V V₂ 1₂ Hump AZ=0.30 m 2
10.85 If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m/s is to occur in the cast-iron pipe? Draw the HGL and the EGL, including relative slopes and changes in slope. Elevation = ? Water T= 10°C Elevation = 110 m В L = 100 m, D= 20 cm, cast-iron pipe L= 150 m D= 15 cm Cast-iron pipe PROBLEM 10.85
: Water flows over a smooth submerged object in a channel of width 1.2 m. The water depth upstream of the object is 2.2 m and the water depth downstream is 0.5 m. i) Use the Bernoulli and Continuity equations to calculate the discharge within the channel, and sketch the energy grade line and hydraulic grade line for this problem. ii) The measured discharge in the channel is 2.4 m³/s. Calculate the discharge coefficient, and describe what this physically represents. iii) A pitot tube (or stagnation tube) is placed in the downstream part of the channel, where the water depth is 0.5 m. Calculate the height to which water will rise within this pitot tube (above the depth of water in the channel).
A town is planning to develop a new water supply from an aquifer. Two observation wells installed 1000 ft apart have respective head of 300 ft and 295 ft above a common datum. Within the aquifer, hydraulic conductivity (Kn) 25 ft/day. The aquifer has a mean width (w) = 2 miles and thickness (b) = 200 ft. Estimate the volumetric flow %3D %3D %3D rate through the aquifer in cubic feet per day. Well 1 h= 300 ft 1000 ft Well 2 h = 295 ft AQUIFER 200 ft suturation 2 miles
ELEV. = 65m A ELEV. 32m L- 1500m 2 - 1400m D- 750mm Q= 1.2 m3/s D= 600mm ELEV. - ?? L= 1800m D= 450mm A three reservoir problem shown in the figure with their corresponding length and diameter. Assuming that each pipe has f= 0.02 and discharge at pipe 1 is 1.2 ma/s, determine the elevation of the surface of reservoir C No answer among the choices B 31.23 m 21.14 m 28.82 m 25.73 m F 18.96 m
ELEV. = 65m 1 2 A L = 1500m D = 750mm Q = 1.2 m3/s ELEV. = ?? C D L = 1800m D = 450mm A three reservoir problem shown in the figure with their corresponding length and diameter. Assuming that each pipe has f = 0.02 and discharge at pipe 1 is 1.2 m3/s, determine the elevation of the surface of reservoir C ELEV. = 32m : B L = 1400m D = 600mm 3
ELEV. = 65m A ELEV. = 32m в 1 L = 1500m 2 L = 1400m D = 750mm Q = 1.2 m3/s D = 600mm ELEV. = ?? D L= 1800m D = 450mm A three reservoir problem shown in the figure with their corresponding length and diameter. Assuming that each pipe has f = 0.02 and discharge at pipe 1 is 1.2 m3/s, determine the elevation of the surface of reservoir C A) 21.14 m В 25.73 m C) 31.23 m 28.82 m E No answer among the choices F 18.96 m
Problem P64 Extending the previous problem. The same two pipes connect two reservoirs as shown on the figure. 100 m Ans: z = 79.337 m Pipe #1 L = 5000 m D 800 mm C = 120 Pipe #2 L = 3500 m D = 1500 mm C = 80 B Determine the elevation of the free surface in Tank B if the total discharge into Tank B is 5.00 m³/s. Adopt a non-iterative approach when solving this problem. Neglect all local losses
ELEV. = 65m 1 A L = 1500m D = 750mm Q = 1.2 m3/s ELEV. = ?? C D L = 1800m D = 450mm A three reservoir problem shown in the figure with their corresponding length and diameter. Assuming that each pipe has f = 0.02 and discharge at pipe 1 is 1.2 m3/s, determine the elevation of the surface of reservoir C (A) 18.96 m (B) 31.23 m 25.73 m 28.82 m E No answer among the choices (F) 21.14 m 2 ELEV. = 32m : B L = 1400m D = 600mm 3
Q3. A well pumping from a unconfined aquifer at steady rate of 293 m³/hr. Two observational wells were installed at distances of 35 and 100 m form the pumping well. Assume h,=45 m Determine the: a. Drawdown (hz' hı) if K = 0.25 m/hr b. Drawdown (hz hj) if K = 0.75 m/hr
Problem 5: An earth dam section is shown below. Draw the flow net and calculate the seepage. 3m 3m 4m 1 1 30m 2 2 k, = 2 x 10-9 m/s k2 = 2k, 90m
A well is installed in a unconfined aquifer. Determine the drawdown (ft) at the well if: the radius of influence = 500 ft. The thickness of unconfined aquifer = 95 ft The well diameter =9 in Pump rate =250 gal/min. Hydraulic conductivity = 0.001 ft/sec. 44 2 33 11 25