Question 2: A residential building construction development is using columns that are 4.2m in hieght. The columns are made from seasoned Western Hemlock of Grade F14, with nominal dimensions of 190x45. Intermediate restraints are provided at 1.05m centres to minimize buckling about the minor axis. For the columns under consideration, intermediate restraints for minimizing buckling about the major axis are located at 2.1m centres. The columns can be considered as secondary members as they are closely spaced enabling load sharing. The columns carry unfactored compressive loads as follows: a permanent (dead) load of 50KN, an imposed (live) roof load of 30kN and wind load of 10kN. Assume that the imposed roof load is infrequent in nature (construction related) and that both the long-term imposed (live) load factor (y) and combination factor for imposed action (y) are equal to zero. Location: Rockingham, Western Australia. Check the ability of the column to support the applied loads if the column is restrained at both ends in position and direction.

Question 2: A residential building construction development is using columns that are 4.2m in hieght. The columns are made from seasoned Western Hemlock of Grade F14, with nominal dimensions of 190x45. Intermediate restraints are provided at 1.05m centres to minimize buckling about the minor axis. For the columns under consideration, intermediate restraints for minimizing buckling about the major axis are located at 2.1m centres. The columns can be considered as secondary members as they are closely spaced enabling load sharing. The columns carry unfactored compressive loads as follows: a permanent (dead) load of 50KN, an imposed (live) roof load of 30kN and wind load of 10kN. Assume that the imposed roof load is infrequent in nature (construction related) and that both the long-term imposed (live) load factor (y) and combination factor for imposed action (y) are equal to zero. Location: Rockingham, Western Australia. Check the ability of the column to support the applied loads if the column is restrained at both ends in position and direction.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.3.1P

See similar textbooks

Similar questions

Figure 1 shows the plan view of an exhibition hall with dimensions L, x L2. The structure is to be constructed in a coastal region which will be exposed to mostly mild environmental conditions, and should provide a 1.5 hour fire resistance. It is known that the underlying foundation soil contains sulfate and other organic compounds. The layout of the structure consists of portal frames which are spaced evenly along the L; direction. The frames are to support a slab of thickness (t) that will cover the full area of the hall plan. The dead and live loads applied on the slab are G and Q (kPa), respectively. Figure 2 shows the elevation view of Frames B and D. All columns have a floor-to-floor height (H) and are monolithically connected to the beams. Columns are also fixed to the foundation at the base, and it may be assumed that all frames are fully braced. в с D E F А в с D E FG Figure 1: Plan of exhibition hall. D D1 D2 D3 L1 L1/2 L1/2 Figure 2: Elevation of Frames B and D. B.
A reinforced concrete tied column is to resist the following axial load: • PDL= 800 kN • PLL = 1050 kN • PEL = 450 kN The concrete used has strength of 20.7 MPa and the yield strength of 415 MPa. Determine the number of 25-mm bars if the steel ratio is 1.5%.
15. A reinforced concrete circular section of 50,000 mm² cross-sectional area carries 6 reinforcing bars whose total area is 500 mm². If the concrete is not to be stressed more than 3.5 MPa and modular ratio for steel and concrete is 18, the safe load the column can carry will be nearly
A simply supported beam is 25 × 50 cm deep and has 2-20 mm Fe415 grade steel bars going into the support shown in figure below. If the shear force at the centre of support is 110 kN at service loads. Assume M20 mix, design bond stress (ta) = 1.2 MPa. Take clear cover to steel = 25 mm 2-20 mmo with referecne to the information provided, (a) The required development length (b) The anchorage length 00 mm
A W14 x 90 of A572 Grade 60 steel is used as a beam with lateral support at 10-foot intervals. Assume that Cb 1.0 and compute the nominal flexural strength. a. Check for compactness b. Determine nominal flexural strength
A simply supported beam shown is to support a total dead load 35 kN/m. Determine the live load that the beam can resist in accordance with the requirements of the NSCP 2015. Use fc'=35 MPa and Grade 60 (fy=414 MPa) rebars. The reinforcements shown are 5-36 mm diameter bars.
Estimate for the concrete, formworks, reinforcement requirement of Beam GG-36. Length of Beam 1 = 8200mm Length of Beam 2 = 8200mm Size of Column = 800mm x 800mm GG-36 IGG-36 GG-131 009*00t GB-4 009*00+ GG-1
ple 7.11 Design a composite beam with flexible shear connectors for the following data: Span of the beam clc distance of beams supporting slab Total uniform load over the beam 5 m 2.5 m 20 kN/m Grade of concrete M-15 Thickness of slab 120 mm Modular ratio (m) 18
Answer Options Correct Q.No Question/Statement Answer A Select the grade of concrete required for 1 М5 M50 M15 М80 airport runways. The load which has fixed size and location is 2 called as Environmental All answers Dead load Live load Load are wrong Top surface of the tensile Bottom The clear cover of the RCC beam is taken as Centre of surface of the Bottom of the gravity of the tensile steel vertical distance from the base of the beam to steel tensile steel beam the reinforcement reinforcement 4 Stocky column generally fails by_ Compression Tension Buckling Deflection In a one way slab the main reinforcement is provided along All answers Both long and short span Long span Short span are wrong All answers Flat slab is placed above Drop panels Column Column head are correct The maximum percentage of reinforcement in 7 RCC short column, based on practical 0.8% 4% 6% 2% difficulties is For reinforced concrete wall D4B When to columns are far, select the type of foundation Trapezoidal…
Problem 1. The composite beam shown below carries a cantilevered load of 10 kN. The beam consists of one 30 x 124 mm plate and four 12 x 50 mm plates. They are pinned together at 120 mm intervals with round pins. The pin material has a shear strength of 159 MPa. Compute the minimum acceptable diameter for the pins. O O O O O O O -0 O 0- O 1000 mm Do O -120 mm (typ) O O O P = 10 KN 30 x 124 mm 12 x 50 mm (typ)
% 5 4. Find the interaction diagram for the following columns with the same cross-sectional area and reinforcement using the specified points. Assume f = 3 ksi, fy = 60 ksi, yh = h - 5". Assume ties conform to ACI requirements and #9 bars are evenly distributed in each cross section. Assume the fiber in extreme compression in flexure is at the top of the cross sections. Q Search 4- a. Maximum compression b. Onset of cracking &$1 = 0 c. Balanced condition Es1 = -Ey d. Transition zone Es1 = -2Ey e. Tension controlled limit Es1 = -0.00507 f. Pure Tension Cross section b= 18" h= 18" Cross section b= 18 in. h 36 in J+ d₁ d₂ d3 & 7 SLED fe 144 15.5 in 9 in 2.5 in * 8 DII d₁ d₂ da hip ( DDI 9 33.5 in 24.25 in 4.5 in insert 4 prt sc T|Y||U || | ||0|| P || T G
A timber beam shown in the figure is made up of Sasalit (50% stress grade). Use LRFD. All thegiven loads shown in the figure below are unfactored service loadings only, it does not include the weight of the beam itself. R₁ WD = 6 KN/m W₁ = 3 KN/m 2 m PDL = 5 KN 1 m PLL = 3 KN 1 m 2) What is the unit weight of the given wood, in KN/m³? 4) What is the actual reaction R₁ in KN? R₂ 3) What is the unfactored weight of the beam itself in KN/m? 500 mm 800 mm