Question #1: The following unbalanced line-to-ground voltages are applied to the balanced Y-load shown in the following figure: Vag V ba Figure 1: Balanced Y-load supplied by an unbalanced voltage source. Vag = 10020°, Vbg = 752180°, and Veg = 50290° volts. The Y-load has Zy = 3 + j4 N per phase with neutral impedance Zn = j1 N. Calculate the line currents Ia, Ib, and I, using symmetrical components. INT IN IN

Question #1: The following unbalanced line-to-ground voltages are applied to the balanced Y-load shown in the following figure: Vag V ba Figure 1: Balanced Y-load supplied by an unbalanced voltage source. Vag = 10020°, Vbg = 752180°, and Veg = 50290° volts. The Y-load has Zy = 3 + j4 N per phase with neutral impedance Zn = j1 N. Calculate the line currents Ia, Ib, and I, using symmetrical components. INT IN IN

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.30MCQ

See similar textbooks

Similar questions

e = 0 Q1: What does happen if we change two currents? a. Q2: What does happen if we have a three-phase four poles machine? Q3: What does happen if we have a two-phase two poles machine? e = 0 Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali Ki. pw --
7. Three load units A, B, and Care connected in parallel and take currents that are respectively 11 A, 10A and 15A. Assuming IA to be the reference phasor, IB leads IA by 30degrees and IC legs behind IA by 65degrees. Calculate the total (resultant) currentand angle it makes with the x-axis.
Q4/For the three-phase power network shown in Figure. the various components are: GI: 100 MVA, 0.30 pu reactance. G2: 60 MVA, 0.18 pu reactance. Transformers (cach): 50 MVA, 0.10 pu reactance. Inductive reactor X: 0.20 pu on a base of 100 MVA. Lines (each): 80 ohms (reactive); neglect resistance. with the network initially unloaded and a line voltage of 110 kV, a symmetrical short circuit occurs at midpoint E of line 2. Calculate the short circuit MVA to be interrupted by the circuit breakers A and B at the ends of the line. T3 38 L1 L2 G2 Bas 12 T4 Bus
One advantages of load balancing is that each phase conductor carries the ? current value
In the system shown in Figure 1, the transformers are connected star-star with both star points grounded and the generators are connected in star with thier star points grounded. The system base is 15 MVA. The transformers all have reactances of 0.04 p.u. on this 15 MVA base. The reactances of all other elements are given in Table 1 (in 2) and the voltage levels are given in Table 2. p.u. G1 p.u. T1 jö Per-Unit Convert all values to p.u. on a 15 MVA base. Xa= p.u. Xc₂= XL = V BABE G1 2 X 9 T3 Figure 1: A section of the distribution system T1 L Table 1: Sequence reactances (2) 3 G1 L G2 0.3 0.59 0.01 4 L 9/10 10 Fault Voltage What is the voltage at bus 3 (in Volts) after the fault has occurred? Vp= V T2 5 T2 34 10/4 Table 2: Voltage bases (kV) G2 4 T3 10/9 | G2 Fault Current A three-phase fault with a fault reactance of 0.01 p.u. occurs at bus 3. Calculate the fault current flowing at the fault point in KA. Ip=-j KA So
Problem 1- Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: A. B Zs (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (13) through impedance Z4. 220V;50HZ Figure 1 Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar Take voltage as reference. notation.
Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
In the circuit of figure shown in the next slide, threeimpedances are 12 – j10 ohms, 10 + j20 ohms, and 15 + j0ohms, connected between conductors a, b, c and the neutral“n” of a balanced 230 volts, 60 hertz, 3 phase, 4 wire, ABCsystem. Using Van as the reference vector, determine:a. Current in each impedanceb. Neutral current Inc. Readings of wattmeters W1, W2, & W3d. Power in each impedance ..
Connect three single-phase transformers in Y-Y, with subtractive polarity, so that the line-to-line voltages on the primary are 30 degrees delayed to their respective line-to-line voltages on the secondary. It should show each step that is needed to make this connection (example: the phasor diagram) and should show the final connection of the three transformers including the polarity markings. Assume phase A on the primary is terminal "H1".
A source of AC emf E₁ = 120/300 volts with an impedance of Z₁ = 2/0° ohms is connected in parallel with another AC source of E₂ = 120/-30º volts with an impedance Z₂ = 2/90° ohms. The two AC source are use to supply a load impedance of Z₁ = 10/-53.10 ohms. Calculate the value of the load current IL. O a. 7.62 amperes O b. 4.42 amperes O C. 5.38 amperes O d. 6.48 amperes
If you have 3-phase power and you need to step down (or up) in 3-phase voltage, how many single-phase transformers are needed? Explain.
Three zones of a single-phase circuit are identified in the figure with a generator voltage specification of 240 V. The zones are connected by the transformers T1 and T2, whose ratings are shown below.Using base values of 30 kVA and 240 volts in zone 1, draw the pu circuit and determine the pu impedance and pu source voltage. Then calculate the load current in pu and in amperes.*Round the final answer to four decimal places, polar form, and label it with the correct units.