Q9.16 A shaft of tubular cross section has an external diameter diameter of 2.5 cm. It is made of steel with Young's modulus of 200 GPa and density of 7800 kg/m³. If the shaft has a length of 2 m, determine its whirling speed. [1283 rev/min]

Q9.16 A shaft of tubular cross section has an external diameter diameter of 2.5 cm. It is made of steel with Young's modulus of 200 GPa and density of 7800 kg/m³. If the shaft has a length of 2 m, determine its whirling speed. [1283 rev/min]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5) Find the horizontal displacement of the floor (mass m) of the building frame shown in Fig. when the ground acceleration is given by x = 100 sin cot mm/sec : Assume: m=2000 kg, k=0.1 MN/m, @= 25 rad / s. and x₂ (t=0)=x₂ (t=0)= x(t=0)= x(t=0)=10. x(1) *(t) = A cos cot K7
Consider the following H = 450 m, L = 5 km, D = 1.2 m, Dj = 20 cm.The penstock is concrete, ε = 1 mm. The impulse wheeldiameter is 3.2 m. Estimate (a) the power generated by thewheel at 80 percent efficiency and (b) the best speed of thewheel in r/min. Neglect minor losses.
7. Pump 50mm Þ 17m Data: f = 0.0067 Pressure at 3 = 194 kN/m² gauge Velocity at 3 = 2.7 m/s p = 830 kg/m³ Pump efficiency = 88% Motor efficiency = 84% Pressure at 1 is atmospheric Velocity at 1 is negligible Determine required input power to motor [1.64 kW] 8. 200mm turbine water gen Data: At 1, p = 230 kN/m² gauge, v = At 2, p = 0 = 0 gauge, v = 0 Turbine efficiency = 80% Generator efficiency = 90% 3.6 m/s %3D Determine output power from generator [19.3 kW]
2%Y\ li. 1:18 HW4.png > The x- and y-motions of guides A and B with right- angle slots control the curvilinear motion of the con- necting pin P, which slides in both slots. For a short interval, the motions are governed by x 20 +t and y = 15 - , where x and y are in millimeters and t is in seconds. Calculate the magnitudes of the velocity v and acceleration a of the pin for t = 2 s. Sketch the direction of the path and indicate its cur- vature for this instant. A II
Head 10lbs mass 4' 10=8" material is elashe and E = 2X10 PS, 8' The Base is sniamly moved with the Velocity of 5 m/s Find the Velocity and Acceleration of Head دے
A section of uniform pipe is bent into an upright U shape and partially filled with water, which can then oscillate back and forth in simple harmonic motion. The inner radius of the pipe is r = 0.024 m. The radius of curvature of the curved part of the U is R = 0.23 m. When the water is not oscillating, the depth of the water in the straight sections is d = 0.37 m. Enter an expression for the mass of water in the tube, in terms of the defined quantities and the density of water, ρ. Use the approximation r << R. Calculate the mass of the water, in kilograms. Take ρ = 1000 kg/m3. Enter an expression for the force constant of the U-shaped column of water when displaced from equilibrium, in terms of the defined quantities, ρ, and g. This constant is analogous to the spring constant in Hooke’s law. Find the value of the force constant, in newtons per meter. Take ρ = 1000 kg/m3 and g = 9.81 m/s2. Calculate the period of oscillation, in seconds.
A water pump produces a flow of 0.25 m /s and a power of 2 kW, using an 300-mm-diameter impeller. Part A What is the flow if a 150-mm-diameter impeller is used to maintain dynamic similitude? Express your answer to three significant figures and include the appropriate units. Part B What is the power if a 150-mm-diameter impeller is used to maintain dynamic similitude? Express your answer to three significant figures and include the appropriate units.
Glycerin at 20 ° C fills the space between a hollow sleeve ofdiameter 12 cm and a fixed coaxial solid rod of diameter11.8 cm. The outer sleeve is rotated at 120 rev/min.Assuming no temperature change, estimate the torque required,in N · m per meter of rod length, to hold the innerrod fi xed.
PROBLEMI.2 A HYDRAULIC TURBINE IS REQUIRED TO PRODUCE 800 KW POWER AT 500 RPM UNDER A NET HEAD OF 40 M. FOR INITIAL TESTING A GEOMETRICALLY SIMILAR MODEL OF 1:4 SIZE NEEDS TO BE TESTED IN A LAB WHERE AVAILABLE HEAD IS 10 M.THE OPERATING SPEED AND POWER PRODUCED BY THE MODEL RESPECTIVELY IS
1. Assume a Centaur V upper stage with an empty mass of 2,247 kg, diameter of 3.05 meters and height of 12.68m, the wall thickness is 41mm, whereas the motor can be assumed to fill up 1/4 of the inner volume. You can assume the density of the walls and the motor to be uniform. You can assume the upper stage has been properly passivated and has no fuel remaining. (a) Compute the inertia tensor relative to the center of mass.
Somewhere DEEP BELOW THE EARTH's surface, at an UNKNOWN displacement from the Earth's center, a particle of mass m is dangled from a long string, length L; the particle oscillates along a small arc according to the differential equation d^2x/dt^2=-(pi^2/36)x. Here x refers to an angular displacement measured from the vertical and t refers to time. The particle's mass is given by m=3kg. The length of the string is given by L=5 meters. Whenever the particle arrives at a location of x=(pi/12) radians from the vertical, the particle has no instantaneous speed. On both sides of the vertical, that is, x=(pi/12) radians is repeatedly observed to be a 'turning point' for the particle's periodic motion. 1. Draw a clear FREE-BODY diagram of this particle at some arbitrary point during oscillation, making sure to label variables and constants described above. 2. Approximating to three significant digits if necessary, what is the angular frequency of this oscillator on a string? 3. Approximating…
Asap Find the whirling speed, Nc, (in cps) of a shaft 10 mm in diameter and 1.0 m long carrying a mass of 2 kg at its midpoint. The density (p) of the shaft material is 30 Mg/m³ and modulus 100 GN/m². Young modulus is Assume the shaft to be freely supported.