Q5: The piston cylinder device (radius=10 cm) contains a liquid with a pressure 100 kpa and temperature of 20 ° C and has a liquid convection heat coefficient =93 WmK. Connect its fixed side to a cubic piece of aluminum (side length 15 cm) with a thermal conductivity coefficient of aluminum = 239 W mK. At the bottom of the aluminum piece there is a heat source with a temperature of 150 ° C, noting that the heat source is located in a vacuum chamber. Radiation thermal resistance = 3.17 K/W. Calculate the change in piston height during I sec. if you know that there is no change in the internal energy of the piston cylinder device. Note IK Watt 1KJ/s

Q5: The piston cylinder device (radius=10 cm) contains a liquid with a pressure 100 kpa and temperature of 20 ° C and has a liquid convection heat coefficient =93 WmK. Connect its fixed side to a cubic piece of aluminum (side length 15 cm) with a thermal conductivity coefficient of aluminum = 239 W mK. At the bottom of the aluminum piece there is a heat source with a temperature of 150 ° C, noting that the heat source is located in a vacuum chamber. Radiation thermal resistance = 3.17 K/W. Calculate the change in piston height during I sec. if you know that there is no change in the internal energy of the piston cylinder device. Note IK Watt 1KJ/s

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.24P

See similar textbooks

Similar questions

8.12 An electric room heater has been designed in the shape of a vertical cylinder 2 m tall and 30 cm in diameter. For safety, the heater surface cannot exceed . If the room air is at , find the power rating of the heater in watts.
Sipho’s mother is making a fire in the stove inside a shack using coal. A fan is used to extract the flue gasfrom the fire via a chimney made of zinc material. The wall thickness of Chimney is L=4mm and the walltemperature of the chimney on the flue gas side is T_si=60˚C. Sipho, playing outside next to the chimneyexperiences an ambient temperature of 20˚C. The surrounding temperature is T_sur=35˚C and the emissivityis ε=0.95. Assume the convection coefficient is 20W/m2K and the chimney is grey material.Under these conditions determine the outer surface (air side) temperature T_so=? of the chimney.
-A per fectly sealed room metors height 10 meters wide, 12 meter? long and 3 Is composed of 49 shudonts and I pro fessor- The piesore and temperature of I atm and o deg C. respechiuely. If a person occopics an averange room has an initial Volume of D-20 ecubic meter and gjuel off 678 kj per nour of heat, what woud be the temperatore of the room af ter 10 mins ! Usc moleculor mass of air M equal to 28.9 kg/mol, specific heat of cir af constant volume Cv cqual to 0.718b HT/kq-k Cand gav constant R eaual to 0.117 k5/kg-u
The thermal conductivities of wood is kwood = 0.1W/(m°C)and air is kair = 0.0234W/(m°C). Part A If the temperature of the room is 20°C and outside is 10°C, find the rate of heat flow for a wall of wood with area = 10 m² and thickness of 5cm. O 60 W O 304 W O 34 W O 200 W O 100 W Submit Request Answer Part B The wall of wood with thickness of 5cm is now replaced with two layers of wood and a gap of air between the wood. Each layer of wood has a 2.5cm thickness and the gap is 1cm. The rate of heat flow will, decreases. increases. stay the same. Submit Request Answer Part C The temperature in the air gap will be, O 20°C, between 10°C and 20°C, O 10°C,
The wall of a furnace comprises three layers as shown in the figuie. The first layer is tery (whose maximum allowable temperature is 1400°C) while the second laver is Tracto:y Chose maximum allowable temperature is 1093°C). The third layer is a plate of 6 35 od thermal contact. Steet plare To 6.35x3 45A 1370 C Concerntiation veluciy 37.8 C mass Siynes Figure. Layers in a composite furnace wall. e temperature To on the inside of the refractory is 1370°C, while the temperature T; on the side of the steel plate is 37.8° The heat loss through the furnace HnIlisexpectet tobe
The physics of the conduction heat transfer of thermosses phenomenon and the mathematical model should be discussed.
There is 100 grams of water in a brass calorimeter of mass 200 grams. It is found that 590 calories are required to raise the temperature of water and container from 20°C to 25°C. What is the specific heat of the brass? COMPLETE FBD SOLUTION AND REQUIREMENTS PS. THIS IS A HEAT TRANSFER PROBLEM
The heat transfer through a wall 25’x10’ is 8750 Btu/ hr. The outdoor air and surface temperature = 20 oF and indoor and surface temperature =70 oF. What is the conductance of the wall?
Q2- Water flows inside a steel pipe with an ID of 2.5 cm. The wall thickness is 2 mm, and the convection coefficient on the inside is 100 Wm? C. The convection coefficient on the outside is 10 W/n C. The pipe is covered with a layer of asbestos. 1-determine the thickness of the asbestos layer at the critical insulation radius of the pipe. 2-calculate the change percent of heat transfer with and without the insulation. 3-commet on your results,
Q2:- A sphere made of pure copper, which is 13 mm in diameter, is 70 °C (at t=0) when it inserted into a gas having a temperature of 25 °C. After 65 s the temperature of the sphere reach 60 °C. Make the appropriate assumption to find the heat transfer coefficient of the gas. What is the temperature of the sphere after 80 s. (A;=TT D2, V= TT D³/6, Lc=V/ A,)
6. a. The heat flux applied to the walls of the biomass combustion furnace is 20 W/m2. The furnace walls have a thickness of 10 mm and a thermal conductivity of 12 W/m.K. If the wall surface temperature is measured to be 50oC on the left and 30oC on the right, prove that conduction heat transfer occurs at a steady state!b. Heating the iron cylinder on the bottom side is done by placing the iron on the hotplate. This iron has a length of 20 cm. The surface temperature of the hotplate is set at 300oC while the top side of the iron is in contact with the still outside air. To reach the desired hotplate temperature, it takes 5 minutes. Then it takes 15 minutes to measure the temperature of the upper side of the iron cylinder at 300oC. Show 3 proofs that heat transfer occurs transiently
6.6 K5f conduction heat transfer has to take place M1 H rom one end to another end of a meta lic cylinder f0 cm cross-secional area, length 2 meter and thermal conductivity as 100 WmK What is the temperature ciferenge betweer the twa ends of the y ndrical par Ob.210°C Oc150 C