Q5: Explain the function of three Forces Involved in A Deflection Instrument illustrate the Explanation with suitable sketches.

Q: Discuss the effect of adding a poles on time response, through the speed response , overshoot…

A: consider the given question;

Q: Draw the equivalent circuits of Class E chopper for the different quadrant operation and write its…

A:

Q: Q.1 a. Repeatability and reproducibility are ways of measuring precision, particularly in the field…

A: i)   Repeatability is basically an instrument reading repetition from a set of reading. The machine…

Q: Explain the following for a class C chopper: a) Draw its circuit diagram and quadrant operation…

A: Chopper/ DC-DC Converter DC-DC converter increases /decreases the dc voltage level at the output…

Q: 5. Thermodynamic closed systems are the systems where:

A: In thermodynamics, a closed system can exchange energy but not matter, with its surroundings.

Q: Give a sample problem regarding this topic and its formula: Maximum Power Developed by a Motor v2…

A:

Q: Figure Q1(c) shows a simple conveyor system used in industry to detect and count number of metal…

A: According to the question, for the given simple conveyor as shown below We need to explain the…

Q: With the use of a table, with no more than 5 points, make a comparison between the  characteristics…

A: In the following section, the comparison between the characteristics of a carbon composite flywheel…

Q: The energy stored in the air gap in joules if e = 1 cm; the air gap area is 0.8 cm2 and the…

A: Fir this problem, first we need to calculate the inductance value. Then only we can find energy…

Q: Explain the AC Operation Of Electrodynamics'" Instruments in detail.

A: Electrodynamic type instrument:             Two fixed coils, a moving coil, a control spring, a…

Q: Questions: 1. Are the experimental and theoretical values of voltages and currents match? Indicate…

A: Part (1): The experimental value is the measured value during the experiment. Whereas the…

Q: What is the rating and application of extra high tension

A: The voltage rating of extra high tension line is from 345 KV upto 800 KV .

Q: Explain the following for a class D chopper: a) Draw its circuit diagram and quadrant operation…

A: A good problem on power electronics. Look below for solution:-

Q: b) Draw the graph and describe the relationship between near-end cross talk and attenuation.

A: we need to draw the graph and state the relationship between near end crosstalk and attenuation.

Q: Q5. What is interface .Explain what is inertial delay. Your answer

A: To verify a design we write test bench to check that it meet specification. Verification can be done…

Q: A Explain the definition and theoretical background of potentiometers. B. Discuss the difference…

A: Electrical and electronics measurement instruments are very important for determining the various…

Q: Given the mechanical system in the figure below,

A:

Q: what are 5 applications of thermodynamics and gases in electrical engineering?

A:

Q: 3. Write about the “Factors Affecting Transient Stability”

A: If the different producing stations regain equilibrium following periodic system interruptions,a…

Q: Distinguish the general working principles of capacitive, resistive, and magnetic sensors. Discuss…

A: The sensor is indeed a device that monitors changes in the external environment and reacts to some…

Q: Explain the difference between  conductive and inductive compensation

A:

Q: Explain the following for a class D chopper a) Draw its circuit diagram and quadrant operation…

A: Chopper/ DC-DC Converter  DC-DC converter increases /decreases the dc voltage level at the output…

Q: What is the basic principle of an electric motor and generator?

A:

Q: What will be the unit of hole mobility

A: The solution is provided in the following section:

Q: Instructions: 1. The +ve and the -ve electrodes are shown in the simulation above, the units on the…

A: A point charge is known as the place in space where a single charge is located. Free space is often…

Q: What is the screened potential?

A: The screened potential is determined between the inter atomic force and the phonon dispersion…

Q: A 500-turn coil is wound on an iron core. When a 120-V-rms 60-Hz voltage is applied to the coil, the…

A: The solution is given below

Q: Derive the EMF equation of static electrical machine.

A: Electrical Machines are generally electromechanical energy conversion devices. These machines…

Q: give some practical applications for the torsional vibration

A: The vibration of an object in angular form is known as Torsional Vibration. These are generally…

Q: What are the topics in Fundamentals in Deformable Bodies that is essential in the profession of…

A: The solution is provided in the following section.

Q: Why nonlinear systems are often linearized?

A: we need to answer why non linear systems are often linearized

Q: Describe and summarize the theories in Electromagnetism following the Maxwells Equations and…

A:

Q: As Electrical Engineering Majors, discuss why the topic of friction is important in the field of…

A: The real world demands the analysis and design of complex systems, which is possible with the clear…

Q: b) Explain why the effective length is less than the total length of a laminated armature .Which…

A: Lamination is used in machines ( Transformer and rotating Machine) to Reduce the eddy current…

Q: discuss the refrigerator

A: Electrical machines can be either generator, transformer or motors. They can be either Ac machines…

Q: what is the meaning by modultion

A:

Q: resistance, R = 116mN. If the field windin armature resistance, Ra =45m2. Determine the following…

A:

Q: (I) Briefly define Stopping power.

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: Explain the use of magnets and magnetism in tape recorders. -how tape recorders work? -what is the…

A: Magnets are used in magnetic compass to find directions, toys, motors, loudspeakers, microphones,…

Q: What is the difference between performance and potential?

A: Performance means the process of completing tasks. In order to be successful in an endeavor, it is…

Q: I CLASS DISCUSSION ITEM 9.8 Piezoresistive Effect in Strain Gages For a typical metal foil strain…

A: For a typical metal foil strain gauge with a gauge factor of 2.0, it is asked whether the…

Q: Question: A ball is dropped from rest from a high building. What is the the speed of the ball 5…

A: A ball is dropped from rest from a high building. So, u = 0 m/sec After, t= 5 sec To find the speed…

Q: Please send the Design of the tank as photo or PDF file  the Design sketch of the tank  is require…

A: The diagram of the tank is presented in the following section.

Q: Q2. Discuss mathematically the force system and equilibrium system?

A: Force system : : A force system system is collection of different forces which acts at the same…

Q: Why it is important to study the determination of the electromotive force (EMF) in reference to…

A:

Q: Discuss about NUMERICAL SOLUTION OF SWING EQUATION

A: This problem is based on the SWING EQUATION in power system.    Discuss about NUMERICAL SOLUTION OF…

Q: Briefly explain the application of thermodynamics in electrical engineering.

A: The detailed answer is solved below according to the given parameters and instructions in the given…

Q: Describe the main advantage of GTO over thyristor.

A: