Q5: Choose the correct answer for the following ( 1. . instructions is not valid. a. MOV DS, 3000H b. РОP СХ c. DAA 2. When the word is to be popped from the top of the stack, the value of stack pointer is... a. incremented by 1 b. incremented by 2 c. decremented by 2 3. A microprocessor has.. ... Data Bus a. unidirectional b. bi-directional c. Both
Q: Computer organization and assembly language Please help me with this. I have to write line by line…
A: .model small ; Type of model set to small .386 ; processor type i386 .stack 100h ; stack address…
Q: Q 5. Write a program with comments to generate a delay of 0.25 s, if the microprocessor frequency is…
A: Explanation: The hexadecimal counter is set by stacking a register with beginning number and…
Q: ACTIVITY 3 Write and assemble a program to: (a) Set SP = OD, (b) Put a different value in each of…
A:
Q: Search PROC ; save a copy of the registers except eax in the stack ; Implement Search here…
A: Actually, registers are used to stores the data/information.
Q: 5- What is the 8085 Assembly Language Instruction That do the follwing The contents of the memory…
A: Here we have explained the working of the instructions regarding to the question.
Q: In microprocessor, zero flag is set to 1 when the result is zero the result is positive O the result…
A: Answers for both with explanation given below
Q: 3. Find the contents of the stack and stack pointer after the execution of the CALL instruction…
A: IP = 673D will be stored in the stack at 1295 and 1294, therefore SS:1295 = 67 and SS:1294 = 3D.And…
Q: From the given code from step 1-step19 a- What are the memory location addresses that will be…
A: A typical memory representation of a C program consists of the following sections.1. Text segment…
Q: Suppose, procedur procedureA, procedure procedur our program. You can find the instructions, memory…
A: The language to order a PC design is involved guidelines and thejargon of that language is known as…
Q: Create a subroutine using registers AX and BX with POP instructions, that averages two 16bit…
A: Here we initially pop it after that found the result.…
Q: In a few words, explain what the stack pointer register is and what it accomplishes.
A: Introduction: STACK POINTER: A stack pointer is a tiny register that contains the address of the…
Q: Write a program that does the following: Assigns integer values to EAX, EBX, ECX, EDX, ESI, EDI,…
A: Actually, given registers.. EAX, EBX, ECX, EDX, ESI, EDI, EBP
Q: All instructions should have the same length for a variety of reasons, including machine design.…
A: Basics A stack machine is a computation technique in which the primary control is maintained…
Q: What occurs when a RET instruction is executed? a procedure is invoked pops top of stack into EIP a…
A: Offset of next instruction pushed on the stack
Q: 2.b.1. After the PUSH and POP instructions, where does the stack pointer go?
A: Stack stores the temporary values to read/write by the user. Stack has the structure of pile of…
Q: Computer Science Submit your code solution in .asm files. Please also submit a screenshot showing…
A: Answer: we have written sequence of the instruction
Q: main() uses t0, t1, t2, s0, B() uses t4, s3, s4, C() uses t1, t2, t3, t4, s0, s5. How many words on…
A:
Q: Branches and Branches Here is a portion of a program. The initial condition codes have the values N-…
A: Branches and BranchesHere is a portion of a program. The initial condition codes have the values N =…
Q: When a subroutine is called, the address of the instruction following the CALL instruction is stored…
A: Program Counter
Q: computer organization and assembly language 1. Write a line by line explanation to this program. 2.…
A: Answer is given below. model small; The CPU alocates small memory for the program .386; For 32…
Q: B- What is the content of the stack register after execute the following instruction (Assuming each…
A: Stack Stack is a linear data structure that follows a particular order in which the operations are…
Q: For the (pseudo) assembly code below, replace X, Y, P, and Q with thesmallest set of instructions to…
A: Consider the procedure procA, which is the caller in the given example.proceA storing some results…
Q: 1-Write microprocessor program using mnemonics to add two numbers 08 and 06.
A: Two Number :- 08 06 Microprocessor Program using mnemonics to add two…
Q: Which register (in 32-bit mode) manages the stack? Why is the stack called a LIFO structure? How…
A: 1. answer: Extended stack pointer manages the stack. 2.answer: LIFO means last in first out. The…
Q: 4. How many instructions were executed to compute the factorial of 10? 5. What is the smallest…
A: Note: As per our guidelines, we are asked to answer first question of multiple questions. Please…
Q: What does the ADD instruction in the strend subroutine do? O It calculates the address of the next…
A: Strend Return a pointer to the end of a null-terminated string. According to above line strend is…
Q: Translate trhe following C code to MIPS. Assume that the variables f, g, h, i, and j are assigned to…
A: Step 1 The answer is given in the below step
Q: Computer organization and assembly language CODED using "Vdos" BELOW IS THE PROGRAM FROM THE…
A: When a user presses a lower case, then an uppercase shows. Uppercase starting from 41h (A) and lower…
Q: What is the address where the ascii string “! = " is stored? What is the value of the stack pointer…
A: ANSWER: ASCII: PCs work utilizing numbers. They accordingly there need a way for a PC to change over…
Q: .MODEL SMALL .STACK 100H .DATA ; The string to be printed STRING DB 'This is a sample string', '$'…
A: .MODEL SMALL .STACK 100H .DATA ; The string to be printed STRING DB 'This is a sample string',…
Q: Question 19 Question text Two types of tokens that need to be identified by the Postfix Machine…
A: As per guidelines, one question is answered at a time. Kindly repost the remaining questions.
Q: What are the purposes of the stack pointer and frame pointer registers? Why does a subroutine often…
A: Note: There are multiple questions are given in one question. According to the rule, you will get…
Q: ASSEMBLY Local variables are stored on the runtime stack, at a higher address than the stack…
A: Given: ASSEMBLY Local variables are stored on the runtime stack, at a higher address than the…
Q: ssor, the stack segment may have a memory bloc a maximu 32K bytes
A: In 8086 microprocessor, the memory segments each have memory of 64k bytes. The stack segment may…
Q: What is the special purpose stack base pointer register called?
A: Special purpose register holds the program state and these registers contains the counter, stack…
Q: (True/False): The CALL instruction pushes the offset of the instruction following theCALL on the…
A: The “CALL” instruction is used to invoke a procedure. It pushes the instruction's “OFFSET” following…
Q: three (address registers) available in the ATmega2560 called and how are they related to the general…
A: General purpose registers: these registers are used to store short-term calculations in…
Q: Below is the initial content of Stack: | Ox2964 | Ox 1252 <<<< Top of Stack Ох 298| | OXE298 |…
A: In the above stack 1.pc ( program counter ) is increased +2, 0x 988 2.STKPTR:point to the top of…
Q: Microprocessors Fill in the following blanks with appropriate answers 4. If there is a carry from…
A: Q4 Auxiliary carry is the right answer This is because the BCD number system use auxiliary flag…
Q: hicroprocessor CPUS do not understand mnemonics as they are, they have to be converted to binary
A: Because microprocessor CPUs do not understand mnemonics as they are, they have to be converted to…
Q: Show the Con tain of the stack after execute instructions bebw and register content 1P= lo0 SP= FFFE…
A: IP=100 SP=FFFE PUSH AX ; pushes AX PUSH BX ; pushes BX CALL SUBROUTINE ; call instruction POP AX ;…
Q: Explain how a stack works. 1. Explain the general operation of a stack. a). Give examples of…
A: Since, question contains multiple sub-parts, we will answer first “2” sub-parts. If you want any…
Q: (c) For the following C statement, write a minimal sequence of LEGV8 assembly instructions that…
A: Here I have solution only for the (c) one. as the C statement: A = D[2] << 4
Q: 9. Assuming that SP=2236H, AX=FFD4H, BX=8875H, and CX=9812H, show the contents of the stack as each…
A: The stack pointer SP will always point at the top-most position in the stack. The current position…
Q: In assembly 68k write the: Initialize the supervisor stack pointer to $8000 Initialize the program…
A: As per policy we are allowed to answer limited,if u need post it again particularly. 1) EXAMPLE: ARG…
Q: What occurs when a CALL instruction is executed? a procedure is invoked offset of next instruction…
A: Due to company policies I am compelled to solve only one question and that is the first question.…
Q: Fill in the blank: A special region of memory used as the stack for interrupt service routines is…
A: Please refer below for your reference: The special region of memory used as stack for interrupt…
Q: What is the contents of the stack after executing the instruction marked by for the first time
A: There is an include file for the specific device you are programming for that will pre-define RAMEND…
Q: Write a line by line explanation to this program. What does the program do at every routine?…
A: Answer is given below-
Step by step
Solved in 2 steps
- Q5: Choose the correct answer for the following (Choose FIVE Only)1. .......... instructions is not valid.a. MOV DS, 3000H b. POP CX c. DAA2. When the word is to be popped from the top of the stack, the value of stack pointer is ......a. incremented by 1 b. incremented by 2 c. decremented by 23. A microprocessor has .............. Data Busa. unidirectional b. bi-directional c. Both4. A microprocessor requires ........... power supply.a. +10V b. +7V c. +5V5. ........... instruction is not conditional jump instructiona. JA b. JMP c. JE6. According to Moor’s Law, number of transistors on an integrated circuit .......... .a. doubled every two years b. tripled every two years c. not change.4. How many instructions were executed to compute the factorial of 10? 5. What is the smallest value of the stack pointer during the execution when finding the factorial of 16 (disregard the incorrect output)?61. If the current values in the stack segment register and stack pointer are C00016 and FF0016, respectively, what is the address of the current top of the stack?
- Knowledge of Stack Data Structure is a must. Create a stack data structure that can hold at most 10 items. Operations: Push, adds a new item on top of the stack. Pop, removes the item on top of the stack Top, returns the top item on top of the stack To add item on top of the stack, enter PUSH followed by the value ex. PUSH 20 To remove the item on top of the stack, enter POP ex. POP To print the value on top of the stack, enter TOP and it will print the top value and exit the loop. ex. TOP Rest assured that the input will not generate IndexOutOfBoundsException Input 1. Operation e.g. PUSH 10, POP, TOP Description PUSH operation always comes first. Number of POP operations is equal to number of PUSH operations TOP will be the last. Sample PUSH·10 PUSH·20 POP TOP Output Enter·PUSH·N·to·add·value,·N·is·int·value Enter·POP·to·remove·value Enter·TOP·to·print·final·result: PUSH·10 PUSH·20 POP TOP 10In assembly 68k write the: Initialize the supervisor stack pointer to $8000 Initialize the program counter to $1000 Reserve locations at $2000 to hold your first name only (Joshua) as text and call it NAM Reserve locations at $3000 to store 9 longwords, call it MEM, and write your family name (Kimmich) as a comment Reserve locations at $12400 to store 32-bit unsigned integer variable called RES (to be computed)Complete the following ():a. A stack is used by the system when a function call is madeb. A stack can become full during program execution
- *C PROGRAM FOR MICROPROCESSOR* Write a C program that will use 7-segement LEDS to display the number of key on the keypad when it is pressed. The display needs to stay on the 7-segment LEDS until the next key is pressed. Interrupt method is not required.Select common examples of when an assembly programmer would want to use the stack: to pass arguments to save return address for CALL local variables temporary save area for registers applications which have FIFO nature, such as customers waiting in a bank queueEvaluate the following statements and choose the correct statement that describing the function of the associated/corresponding register.i. R13 is used as the stack pointer and stores the address of the next empty entry or top of the stack.ii. R14 is link register where the microprocessor stores the return address when executing a subroutine.iii. R15 is the program counter and contains the address of the next instruction to be executed. A. i and ii and iii are true B. i and ii are true C. None of above are true D. ii and iii are true E. i and iii are true
- A set of instructions may be used to show the return address of a function. Remember that any changes to the stack must not prevent the procedure's return to its caller.SPIM: 1.made a program (SPIM) that can find the values of a function f(a,b) =a+b using stack and the jump and link instruction. (i.e. a=2, b=3) 2.Add the items of an array using SPIM. Find the summation of all the previous elements in a loop and show them up.Select the statements that directly apply to the operation of the RET instruction. transfers control to return address located at the top of the stack places return address on the stack return is made to the instruction that follows the CALL instruction