Q5: A concrete wall for a building is 50 m long, 40 cm thick, and 4.5 m high. Pouring it requires the use of a concrete mixer with a productivity of 12 cubic meters per cycle. The duration of one cycle is 12.5 minutes and the number of work minutes per hour is 50 minutes. If you know that the expected temperature of concrete during pouring is 30°. find The amount of lateral pressure applied by the soft concrete to the wall form, which is taken into account when Template design. Then find the time required to pour the entire wall.

Q5: A concrete wall for a building is 50 m long, 40 cm thick, and 4.5 m high. Pouring it requires the use of a concrete mixer with a productivity of 12 cubic meters per cycle. The duration of one cycle is 12.5 minutes and the number of work minutes per hour is 50 minutes. If you know that the expected temperature of concrete during pouring is 30°. find The amount of lateral pressure applied by the soft concrete to the wall form, which is taken into account when Template design. Then find the time required to pour the entire wall.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Note: If you don't know the solution please leave it but don't give me wrong solution. Give me clear calculations. A concrete floor is constructed of 3 wythes of carbonate concrete that is each 2 inches thick. If the concrete is normal weight (145 lb/ft3 ), what would be the resistance of the floor? A.1.2 hours B. 0.43 hours C. 3.9 hours D. 2.78 hours
Q1. What do we mean by curing concrete? What will happen if concrete is not cured?
Calculate the density of the concrete Volume of the bucket = 0.00727 m3 Mass of empty bucket = 4.85 kg Mass of the bucket + concrete = 21.8 kg
CONCRETE PRESSURE We are pouring 12-foot-high concrete columns with self-consolidating concrete, and each column can be placed in an hour. The concrete sets after about 8 hours. If the self-consolidating concrete weighs 170 lb/cf and has a chemical coefficient Cc of 1.4, what is the maximum pressure on the column forms?
Q4/ A concrete mixture has 310 kg cement, 550 kg sand, 1300 gravel and 185 kg water. Calculate the followings: A. The temperature of the mixture if you have temp. of cement= 55°C, temp. of sand= 30°C, temp. of gravel= 35°C and temp. of water= 25°C. B. The required amount of ice to reduce the concrete temperature to 20°C.
A concrete has a height of 5 meters and has unit area of 3 m3 supports a mass of 30, 000 kg. Determine the following: Stress Strain Change in height Acceleration due to gravity (g) = 10 m/s2 Young modulus of concrete = 20x109N/m2
*I E,90 KB/S H.W (4)-2nd cours... Concrete technology H.W (4) (A) Give reasons: Very early strength of concrete increases if temperature during placing and setting is increased. This is not the case for concrete strength after 7 days. (B) / Explain the following curve (use your own words (DO NOT COPY FROM THE LECTURE & DO NOT COPY FROM OTHER RESOURCES). 10000 Age at Test ePonded 8000 Hessian days 6000 bnded Hessian 4000 Ponded days Hessian Ty 2000 032 040 Woter / Cement Ratio 036 044
A column has a radius of 150 mm and a height of 3 meters. The density of concrete is 2.45 Mg/m^3. Determine the weight of the column in pounds.
Ultrasonic pulse velocity (UPV) test in through transmission is applied on a concrete sample. If the travel path is 12 cm and transit time is 24 us, what is the UPV of this concrete sample? Comment on the quality of the concrete? O a. 2000 m/s, weak O b. 200 m/s, very weak O c. 5000 m/s, very good O d. 500 m/s, very weak O e. 3500 m/s, questionable
n=20 1. The relation between concrete strength (E) and maturity (M) is as follows: fe = (5+ +10 log10 M. Calculate the strength when concrete is cured at (20 +)°C for (7+") days. What temperature would be required to reach a strength of 30 MPa at 28 days?
A concrete test cylinder having length L=12 in and diameter d=6 in is subjected to axial compressive forces P in a testing machine. If the maximum shear stress in the concrete is not to exceed 2,000 psi, what is the safe value for the axial load p?A. 452,389 lb. B. 113,100 lb. C. 904,778 lb. D. 56,550 lb. The answer for this is letter B 113,100 lb but I dont know its solution. Please give me complete solution in order to get the 113,100 lb.
Based from the proportion that you have designed, say that the concrete is mixed to fill 20 cubes (100 x 100 x 100mm) and 10 prisms (500 x 100 x 100mm), find the mass of each material based on the aggregate conditions in Table 2.