Q3) s) For a beam with a cross section of equilateral triangle of side length a = 20 mm, (a) draw the shear and moment diagrams and determine the maximum values of shear and moment throughout the beam. (b) Determine the maximum tensile and compressive bending stresses and the locations they occur. 150 N/m 10 N.m В C 0 00 '100 mm 200 mm 300 mm 80 N

Q3) s) For a beam with a cross section of equilateral triangle of side length a = 20 mm, (a) draw the shear and moment diagrams and determine the maximum values of shear and moment throughout the beam. (b) Determine the maximum tensile and compressive bending stresses and the locations they occur. 150 N/m 10 N.m В C 0 00 '100 mm 200 mm 300 mm 80 N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1. Figure below shows a simply supported beam that has a rectangular cross section 120 mm wide and 200 mm high. a. Determine the maximum bending stress in the beam. b. Calculate the bending stress experienced by a point on section B that is 25 mm below the top of the beam. (Consider the distance of this point from the N.A when solving this part) |15KN 6 kN/m B D 0.8 m 2 m 1.0 m R = 14 kN RE = 19 kN
Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 5.0 ft, b = 3.4 ft, P = 25 kips, and w = 1.1 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment.Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
For the beam shown in the figure, Determine the following unknowns where L1 = 5m, L2 = 3m, and the moment reaction of the fixed support is 157.5 kN-m clockwise. (DON'T FORGET THE UNITS) Internal Hinge L1 L2 Solve the value of "w": kN/m Solve the reaction of the roller support Solve the vertical reaction of the fixed support
1. The cantilever beam AH is acted upon by a uniformly distributed downward load of intensity 4P/L(force/length)between A and B, a concentrated moment M-2PL at C, and a vertical force Pat D. Using P=20kN and L=1.2 m, construct the shear force and bending moment diagrams for the beam. Mark numerical values for points A through H, along with max/min values on these diagrams. 4P/L Mo L/4 L/4 L/4 L/4 A C H V(x)/P M(x)/PL
Draw the shear and moment diagram of the cantilever beam shown below. For this part, please show the necessary solutions using the long method, not the area moment method. Each correct line/curve with degrees equates to 1 pt. 10 kip 8 kip 3 kip/ft 40 kip-ft 6 ft 4 ft
Determine the absolute maximum normal stress (in unit of MPa) in the beam with external loadings shown below. The beam has a uniform square cross-section with lateral size a = 0.2 m. Note: (1) the shear and moment diagrams can be calculated by either section method or graphical method; (2) there is a concentrated load at point A and a bending moment at point C. 20 kN w = 20 kN/m Mc = = 80 kN · m || В A¬Q C y 2 m 2 m 2 m
Q1) A simply supported beam is 3 m long and carries a vertical load of 5 kN at point 1m from the left-hand end. At a section 2 m from the left- hand end a clockwise couple of 3 kN.m is exerted, the axis the couple being horizontal and perpendicular to the longitudinal axis of the beam. The cross section of the beam shown in the figure. Determine the maximum bending stress set-up. 100 60 All dimensions in mm 100 70 30 EERI
Q1) A simply supported beam is 3 m long and carries a vertical load of 5 kN at point 1m from the left-hand end. At a section 2 m from the left- hand end a clockwise couple of 3 kN.m is exerted, the axis the couple being horizontal and perpendicular to the longitudinal axis of the beam. The cross section of the beam shown in the figure. Determine the maximum bending stress set-up. 100 60 All dimensions in mm 100 70 30 EERING
Given the beam shown below, determine the shear force and bending moment at point C. Given the dimensions a = 2 m, b = 5.9 m and c = 2 m, and the load intensities e = 10 kN/m and f = 2 kN/m. e kN/m f kN/m am bm cm A B D Shear force (observe the up on the left, down on the right positive sign convention): SFc = Number Units (tolerance 0.2 kN) Bending moment (observe the sagging positive sign convention): BMc = Number Units (tolerance 1 kN*m)
1. Calculate reactions at the external supports. 2. Draw the free body diagram. 3. Build the diagrams if shear force and bending moment. (use the section method) 4. Find the diameter of section of the beam. 5. Calculate the maximum Tangential Stress and show the corresponding section. 6. Draw the stress distribution diagram in the most dangerous section of the beam. a (m) 4 b (m) | P (kN) q (kN/m) 1 80 8 A D-? [G] - 100 MPa a q B b P
Q1) A simply supported beam is 3 m long and carries a vertical load of 5 kN at point lm from the left-hand end. At a section 2 m from the left- hand end a clockwise couple of 3 kN.m is exerted, the axis the couple being horizontal and perpendicular to the longitudinal axis of the beam. The cross section of the beam shown in the figure. Determine the maximum bending stress set-up. 100 60 All dimensions in mm 100 70 30
The simply supported beam is subjected to the force F = 700 N and the uniform distributed load with intensity w = 150 N/m. Draw the shear force and bending moment diagrams (in your homework documentation) and determine the equations for V(r) and M(x). Take a = 0 at point A. 19 F a Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 5.2 m 2.6 m 3.12 m Support Reactions The reaction at A is N. The reaction at D is N. Shear Force and Bending Moment Equations In section AB: V(x)= N and M(x)= N-m. In section BC: v(x)- N and M(x)= N-m. In section CD: V(x)- N and M(x)= N-m. A