Q2/the water is flowing through a taper pipe of length 100 m having diameters 600mm at the upper end and 300mm at the lower end, at the rate of 50 liters/s .the pipe has a slope of 1 in 30. Find the pressure at the lower end if the pressure at the higher level is 19.62 N/cm².

Q2/the water is flowing through a taper pipe of length 100 m having diameters 600mm at the upper end and 300mm at the lower end, at the rate of 50 liters/s .the pipe has a slope of 1 in 30. Find the pressure at the lower end if the pressure at the higher level is 19.62 N/cm².

Name: Q2/the water is flowing through a taper pipe of length 100 m having d
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Q2/the water is flowing through a taper pipe of length 100 m having diameters 600mm at the upper endand 300mm at the lower end, at the rate of 50 liters/s the pipe has a slope of 1 in 30.Find the pressure at the lower end if the pressure at the high

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

= Water flows into a tank and out through another pipe, as shown in the figure below. The water in the tank has a surface area, Asur f 5.6 m². At the bottom of the tank there is a door inclined at an angle = 25 degrees with respect to the horizontal. The door has a length L = 1.1 m and a width w=1 m (out of the page). The flowrate into the tank is Q₁ (t) flowrate out is Qo(t) = 0.05 m³/s At time t = Asurf = 0.26 m³/s and the 0, the water has a depth ho = 2.5 m. The density of water is p = 1000 kg/m³. Ө h(t) Qout
Q2: Water flow in a pipe as shown in the figure if the velocity of the fluid at section A is 1.8 m/s and at section D 1.36 m/s. Find A 1. pressure drop at section C d-300 mm d-400 mm 2. head losses at section D Take the density of water 1000 kg/m³ and viscosity of water 998 × 10-6 N.s/m² B 5 m- d-150 mm d-125 mm D
Q2/ A fluid containing (water, oil, sand) flowing through the tube and open to the atmosphere as shown in the figure below.. Note that p°- 1.013*105 Pa Calculate the absolute pressure (Pa). Density: Pwater = 1000 kg/m Pail = 800 kg/m Pand = 200 kg/m P. h3=12 cm hg al2cm oIL Pa h25 cm ng = 6 cm %3D Sand water
1.Find the diameter of a pipe of length 3000 m when the rate of flow of water through the pipe is 300 litres/s and the head lost due to friction is 5 m. Take the value of C = 50 in Chezy’s formula.
The oil flows through the vertical venturi tube as shown in the figure. The venturi inlet has a diameter of 20 cm, the isthmus of the venturi is 10 cm in diameter, the pressure at inlet P1 is 41.4 kPa(gage), and the pressure at the isthmus P2 is the same size as the body of water. The same oil which is 1.52 m. Find the flow rate of this oil. The density of the oil is 849 kg/m3.
Water is flowing downward in a pipe in the figure shown at 0.02 cu. m. per sec. having diameters of 8 cm. and 4 cm. respectively. Determine the values of pressures (a) at pt. 2, P2 and (b) at pt. 1, P1 if the pressure at pt. 1 is twice as great as the pressure at pt. 2. H20 8 ст. Ф 1.5 m 2 datum 4 cm. Đ
Water is flowing at the rate of 1.676 m/s in a 3.068 inches’ diameter horizontal pipe at apressure p1 of 68.9 kPa. It then passes to a pipe having an inside diameter of 2.067 inch. Thedensity of the water is 998 kg/m3.a) Calculate the new pressure p2 in the 2.067inch pipe. Assume no friction losses.b) If the piping is vertical and the flow is upward, calculate the new pressure p2. The pressure tap for p2 is 0.457 m above the tap for p1.c) Compare and discuss your answers in 2 (a) and 2(b).
Q2/: As shown in the figure, the Assumptions of the flow through the venturi is steady, incompressible, irrational with negligible frictional effects , the effect of air column on the pressure change is negligible, the pressure can be assumed to be uniform at a given cross-section of the venturi meter and the flow is horizontal . Air is flowing through a venturi meter whose diameter is 2.6 in at the entrance part (location 1) and 1.8 in at the throat (location 2). The gage pressure is measured to be 12.2 psia at the entrance and 11.8 psia at the throat. Neglecting frictional effects, take the air density to be 0.075 lbm/ft. 1. Show that the volume flow rate can be expressed as: 2(P P2) | = A, p(1 – AŽIA}) 2. Find the flow rate of the air? 12.2 psia 11.8 psia Air 2.6 in 1.8 in
Q5) Water flows radially between the two flanges at the end of 0.2 m diameter pipe as shown in Fig. Neglecting losses, if the pressure head at A -0.4 m find the pressure head at B and the flow in m/s. 1-2 m + 0-6 m 40-025 m B 2.0 m 0.2 m dia
6. Water is flowing through a pipe having diameter 300mm and 200 mm at the bottom and upper end respectively. The pressure at the lower(bigger) end is 25 N/cm2 and the pressure at the upper end is 10 N/cm2. Determine the difference in datum head if the rate of flow through pipe is 40 lit/s.
A pipe with unequal ends is used to transport a fluid. The pipe diameter at the larger end is 0.81 cm and the other end is 0.28 cm. The larger and smaller ends are located 10 m and 4 m, respectively, from the datum line. If the flow at the 10 m datum line is 1.60 m/s and the pressure is 5244 kN/m2, compute for the pressure, in kPa, at the smaller end. Express your answer in 3 decimal places.
s subjected to a gauge pressure of 2.902 psi, applied by a compressed air introduced into the top of the tank. There is a small hole (diameter = 1.57 in) in the side of the tank Water in an enclosed tank is %3D 16.4 ft below the level of the water. Calculate the discharge rate. Answer: ft3/s (2 decimal places)