Q2/Design an Ayrton shunt by indirect method to provide an ammeter with current ranges 6A, 25A, and 100A, if PMMC Irt Ka Ir2 Im Rb Rm meter have internal resistance of 1002 and half scale current of ImA. Re

Q2/Design an Ayrton shunt by indirect method to provide an ammeter with current ranges 6A, 25A, and 100A, if PMMC Irt Ka Ir2 Im Rb Rm meter have internal resistance of 1002 and half scale current of ImA. Re

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Related questions

Q: Problem 42 (a)Determine V, I, Iz,and IR for the network if R1 = 180 2 (b)Repeat part (a) if RL = 470…

Q: A multirange ammeter was designed using direct method to give three scales with Rsh1%= 0.001285989…

Q: 3. (a) A copper-constantan thermocouple with temperature of one junction is 100 °C and another…

Q: (c) Design a voltage regulator using the circuit in Figure 3. The voltage regulator is to power a…

A: Draw the circuit diagram, representing the current direction.

Q: Sketch and describe the construction of a moving-coil ammeter and give the principle of operation. A…

Q: Table 7.3 Electrical characteristics of PV module A and module B Characteristic at STC Module A…

A: As we know, in solar panel standard test condition is Irradiance is 1000 W/m2 at module temperature…

Q: For Figure 3, Vee 2240 ov FIGURE 3 a) Draw the de analysis cquivalent circuit and ac analysis…

Q: A coil consists of 2000 turns of copper wire having a cross-sectional area of 0.8mm². the mean…

A: Given data, Number of turns N=2000 turns Area, A=8 mm2=0.8×10-6 m2 Length, L=0.8×2000=1600 m…

Q: 1. Sketch V, and determine Vae, Vrms 100 V Si 4.7 A2 56 k

A: Since you have posted the multiple questions so we are supposed to answer the 1st question only.

Q: Example: 1.16 A moving coil instrument gives a full scale deflection of 10mA, when the potential…

Q: A PMMC instrument has internal resistance of 0.59 kn and gives full scale deflection for resistance…

Q: Design an Ayrton shunt by indirect method to provide an ammeter with current ranges 1A, 5A, and 10A,…

A: Analog instruments are classified into 3 types Indicating instrument Integrating type instrument…

Q: Q2/Design an Ayrton shunt by indirect method to provide an ammeter with current ranges 6A, 25A, and…

Q: A PMMC instrument has internal resistance of 0.77 ko and gives full scale deflection for 35 mA. The…

Q: 03.) The circuit below is called a “center-tap" full-wave rectifier. It uses a split secondary…

Q: can you create a diagram of this circuit? resistance:220 ohm diode 1N4007 BC548B Transıstor 1.5…

A: Given data: Resistance = 220 Ω Diode : IN4007 Transistor: BC548B Coil Battery : 1.5 V Capacitor =…

Q: Group 1 Q1) Design with drawing a multi range Ammeter (direct method) for the range 50mA, 100mA and…

A: In this question , we have to design multi range ammeter or increasing range of galvanometer by…

Q: Integrate 5-stage voltmeter, 5-stage ammeter and 3-stage ohmmeter

A: consider the given question;

Q: QI Design a multi range D.C. ammeter by using indirect method to give the following ranges 600 mA,…

A: DC Ammeter Internal resistance of PMMC meter = 30 ohm Full scale current 5mA Design a multi meter…

Q: 1. Consider a half-wave rectifier circuit of Fig 5 with a resistive load of 25 Nand a 60 Hz ac…

Q: Vc R1 RC Q1 NPN +88 8 R2 RE Volts VC

Q: The potential transformer used for in power substation To protect power system from surges To…

A: In this question we need to choose a correct option.

Q: Design an Ayrton shunt by indirect method to provide an ammeter with current ranges 6 A, 9 A, and 13…

Q: Determine the DC currents (Ig, Ic and lĘ) and dc junction voltages (VBE, VCE and VCB) IB=Blank 1 mA,…

Q: 2: Fill in the blanks: 1- Conversion (0.88µA) to (nA) is 2- The number of electrons pass through the…

Q: Design a multi-range voltmeter (250 volts) and 350 volts (note that the internal resistance of the…

A: Given data, V1 = 250 V. V2 = 350 V. Ig = 2 mA. Rg = 20 Ω.

Q: CHARGE CONTROLLER 6VDC 6VDC 6VDC 6VDC 350AH 350AH 350AH 350AH BATTERY STORAGE

Q: A moving coil milli ammeter has a resistance of 5 ohm and a full scale deflection of 20mA. Determine…

Q: (a) Refer to the circuit in figure 1 below: R= 5 kN ww V = 10 V Y VD Figure 1 i. Determine and draw…

A: we need to determine and draw load line and calculate the VD for the 3.5 mAmp and power dissipated…

Q: A PMMC instrument has internal resistance of 0.58 kn and gives full scale deflection for 28 mA. The…

A: we will find voltage across the meter and then we will calculate the voltage across the multiplier…

Q: Q1 Design a multi range D.C. ammeter by using indirect method to give the following ranges 500 mA,…

Q: 2/2 pts For a triac circuit shown in figure 5, determine the firing angle if the triac will turn on…

A: The solution is given below

Q: A PMMC instrument has internal resistance of 0.66 kn and gives full scale deflection for 30 mA. The…

A: To use voltmeter as a multi range voltmeter we have to add series resistor.

Q: Q2/ D'Arsnoval moving coil meter that modified to measure AC current with full wave rectifier, if…

Q: Design an Ayrton shunt by indirect method to provide an ammeter with current ranges 1A, 5A, and 10A,…

Q: C) The PV technology has produced long term stable modules. c-Si Thin Film Silicon III-V CIGS CdTe…

A: 1 Silicon is by far the most common semiconductor material used in solar cells, accounting for about…

Q: Q2/ D'Arsnoval moving coil meter that modified to measure AC current with full wave rectifier, if…

Q: Ammeter E) Voltmeter PV Module Potentiometer as Electrical Load PV Cell (size: 1 cm x 5 cm) Voltage:…

A: Well the question instructions aren't clearly mentioned, But from given data & instructions,…

Q: A 2-wire d.c. distributor 81 m long at a distance of 59 m is uniformly loaded with 0.26 A/r…

A: a) Voltage drop=IRVoltage drop at 1 meter V1=0.26×1×1.78×10-3×1Voltage drop at 2 meter…

Q: Problem 2.3] a wire having a diameter of 0.02mm and a resistivity at 20°C of 4.3µQ-cm. If a =…

Q: (i) Draw a circuit diagram of a DC analog ammeter with a current range of 1 A, 5 A and 10 A using an…

Q: The power usage of a DC strip heater is to be determined at a 95% confidence level, using a…

A: The given data's are, The confidence level is 95%, Nominal value of E=8 V, R=5 ohm.…

Q: Group 1 Q1) Design with drawing a multi range Ammeter (direct method) for the range 50mA, 100mA and…

A: In this question we have to design multirange ammeter by connecting shunt resistance acties meter..

Q: Design an Ayrton shunt by indirect method to provide an ammeter with current ranges 1A, 5A, and 10A,…

A: An Ayrton shunt : This is also called universal shunt. which is shown below Given that I1=10A,…

Q: The working coil of a 0-400 V moving - iron volmeter requires 300 ampereturns to give full - scale…

Q: In bipolar junction transistor terminology, evaluate the 'thermal voltage' at 332 K temperature

A: Given data: The given temperature is T=332 K

Q: QI. Describe A- Dual-slope digital voltmeter. B- Electrical Standards.

A: A. DUAL SLOPE DIGITAL VOLTMETER The double incline incorporating type DVM coordinates the…

Q: Design an ammeter to measure 100mA using a 50μA PMMC meter movement with internal resistance 3k Ω.…

A: Consider the current to be measured is of 200 mA The range of the PMMC is 50μA The internal…

Q: A copper conductor (wire) used in a 30 amp common household circuit has a resistance of 1.73 Ω/1000…

A: Whenever a current flows through any conductor of resistance Then there exist power loss in the…

Concept explainers

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.

Question

Q2/Design an Ayrton shunt by indirect method to provide an
Irt
Ra
Ir2
Im
ammeter with current ranges 6A, 25A, and 100A, if PMMC
meter have internal resistance of 1002 and half scale current
Rb
of ImA.
Re

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

How is a solid-state diode tested? Explain.
What is the difference between a diode and rectifier?
In a single phase full wave controlled rectifier connected to Inductive load (with freewheeling diode) find the expression for the average value of voltage across the load when supply voltage is Vs = Vm sinwt and firing angle = a. Vm/TT cosa 2Vm/TT cosa Vm/TT (1+cosa) 2Vm/TT (1+cosa)
Consider the circuit shown in Figure 2. The cut-in voltage of each diode is . Let and assume both diodes are conducting. Determine if this is a valid assumption and explain your answer. And calculate the values of IR, ID, Ip2, and V.. Rj =1.7 kQ ww VB =1 V D1 Dz R2D 4 kQ Figure 2
In RL load connected (without free transition diode), single phase, uncontrolled, full wave rectifier (4 diodes), the source voltage is sinusoidal and its effective value is 44Volt, 50 Hz. The ohmic load value connected to the circuit is 10 ohms. Average value of load current calculate. (L>>R) a) 4.16 A b) 3.46 A C) 3.26A d) 4.56 A e) 3.96 A
Q2) Explain the working of zener diode on both forward and reverse bias. From the circuit in the Figure-2, Rs=1KO, Vz=7.2V and RL=3KN. If Vs = 12V. Find out the following DC parameters: a) Is = ?, Current passing through resistor Rs b) IL = ?, Current passing through resistor RL c) Iz = ?, Current passing through Zener Diode d) VL= ?, Output Voltage (Figure-2) Rs 1k Ohm Is Iz RL VL Vs UA723_ZD2 .3k Ohm 12 V
consider the figure below that shows an approximated reverse recovery turn-off characteristics for a power diode. Show that the following relation can express the total reverse recovery charge, Qrr = 1/2(trr*ts1) di1/dt =1/2(trr*ts21) di2/dt * ip Isl 1s2! -Ir
Q3/a/ what is the function of the inductance (L) in a single phase half wave thyristor ? b/ For 3 phase half wave rectifier source voltage is 100 sinwt with a = 40° find the Vav and draw the output voltage?
How is Zener diode connected into a circuit? What determines the voltage at which a Zener diode break down? What considerations go into determining the power dissipation rating of a Zener diode? Draw a label the schematic symbol used to represent a Zener diode What determines the maximum Zener current of a Zener diode? What is the difference between the maximum Zener current and the reverse current for a Zener diode? What does a positive Zener voltage temperature coefficient signify? What does a negative Zener voltage temperature coefficient signify? How can a Zener diode be temperature compensated?
5-For single phase half-wave controlled rectifier with a freewheeling diode connected across the inductive load, the supply voltage is 220V (RMS). The mean value of the output voltage for a=45 is: 100.7V 70.9V 84.5V 6-For fully controlled single phase bridge rectifier with inductive load (R=102, L=50mH), F=50HZ and a=45', the load current is: Continuous discontinuous verge continuous 7-Fully controlled three phase bridge rectifier circuit is supplied through delta-star transformer. For highly inductive load, the waveform of the line supply current (primary line current of the transformer) is: Square quasi-square six- step
Determine Q-point for the diodes in the circuit given below using the ideal diode model where, R1 = 12.2 kΩ, R2 = 16 kΩ, and R3 = 14 kΩ. (Note: Label the diodes from left to right.)
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D