Q2/A column is supported by a base plate, pedestal, and footing, as shown. The load applied on the column is 300KN. Neglecting their weights, find the bearing stress under each of the four elements. 300KN -Column W 150 x 24 Square base plate (5000 x 5000) 600 diameter pedestal Square footing (11,000 X 11,000)

Q2/A column is supported by a base plate, pedestal, and footing, as shown. The load applied on the column is 300KN. Neglecting their weights, find the bearing stress under each of the four elements. 300KN -Column W 150 x 24 Square base plate (5000 x 5000) 600 diameter pedestal Square footing (11,000 X 11,000)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem No. 3A beam 200x450mm is reinforced by 2-32mm diameter rebar. Assume Cc-50mm, stirrups-10mm, fc'-21Mpa and fy-415Mpa. Calculate the following. 17. Calculate the strain of the steel reinforcement O 0.00182 O 0.00201 O 0.00224 O 000391 O 0.00577
Topic: BEAM BEARING PLATES AND COLUMN BASE PLATES Please solve your Solution in a handwritten Note: It should be handwritten pleaseeee Questions:Design a column base plate for a W12 × 65 column supporting a service dead load of 850 kN and a service live load of 1380 kN. The column is supported by a 2.7 m x 2.7 m concrete footing. Use ASD. Fc'= 20.7 MPaFy = 248 MPad=308mmbf = 308 mm
A rectangular bear has a wish of 300mm and a total depth of 650mm , calculate the area of steel reinforcement repral Take, M. 360kN.m f30 MPa and , 400MP
EXAMPLE-H.W. For the foundation shown in the below; estimate quantity of Reinforcement. Depth of foundation = 1.00 m, 5 0.5 m 16db 0 100 150 60db 20@200
A 300 mm X 550 mm reinforced concrete edge beam is monolithically casted to a 120 mm slab. The beam is an exterior beam reinforced with 5 - 028 mm bars for tension and 010 mm bars for stirrups. If a Ø100 mm and a 075 mm pipe pass through the beam's cross-section, the center of the pipe is located 120 mm and 140 mm, respectively from the top of the flange. Determine the following using an f'c = 21 MPa and fy = 414 MPа: a. Use NSCP 2015 to layout the reinforcement of this beam. i. The overhanging flange width, if the depth of compression block is just enough to include the two pipes. ii. Ultimate Moment Capacity of the Beam Balanced Steel Ratio iii. iv. Centroid of the Beam's Cross Section neglecting the reinforcement.
SEATWORK: (In a coupon bond, copy and answer the given problem. Box your final answers. Submit your output in a single PDF file.) 450 n The 1.5-m concrete post is reinforced with six steel bars, each with a 28-mm diameter. Knowing that Es = 200 GPa and Ec = 25 GPa, determine the normal stresses in the steel and in the concrete when a 1550 KN axial centric force P is applied in the post. 1.5 m
Design the slab of the plan shown below. The dead load is due to self- weight plus weight. of: ▪ Tiles 3 cm ▪ mortar 2 cm sand 7 cm plaster 2 cm ▪ partition 2kN/m² Live load -2.5 kN/m² fe=25 MPa and fy = 420 MPa. 10.00 m 0.30 m -4.80 m- +0.30 m -3.30 m +0.30 m
Define Design controlled by bearing capacity
1. Reinforcement is one of the primary uses of geotextile in foundationa.True b. False c.Maybe d. None 2. A geogrid is geosynthetic material used to reinforceda.True b. False c.Maybe d. None 3. As a Civil Engineer aspirant, explain why soil exploration is important and discuss briefly the methods used for soil exploration
Define Applying Allowable Bearing Pressures—ASD
Discuss Structural dead loads
UPVOTE will be given! Please write the solutions completely and legibly. Box the final answer. Use two decimal places. A reinforced concrete beam 30 mm x 300 mm with tensile reinforcement of 1 - 28mmØ is simply supported over a span of 5.5 m. Using steel covering of 75 mm, concrete strength is 20.7 MPa and yield strength of re-bars is 280 MPa. a. Determine the cracking moment of inertia. b. Determine the moment capacity of the beam. c. Describe the mode of design.