Q2. Four gears are attached to three shafts which transmit different torques as shown in Figure 2. Section AB and BC are solid whereas section CD is hollow with inner and outer diameters of d¡ and do. Individual data of the shaft will be given to each student. Based on the given data, students should perform the following tasks: • Calculate torques on each section of the shaft. • Draw the free body diagram of the torques applied on the shaft. • Calculate the maximum and minimum stresses on section CD. • Calculate the shaft diameter on section AB and BC for the given allowable shear stress of these sections. TD GGGK (di,do) TC d2 TB TA L3. Figure 2: A Shaft loaded with different torques

Q2. Four gears are attached to three shafts which transmit different torques as shown in Figure 2. Section AB and BC are solid whereas section CD is hollow with inner and outer diameters of d¡ and do. Individual data of the shaft will be given to each student. Based on the given data, students should perform the following tasks: • Calculate torques on each section of the shaft. • Draw the free body diagram of the torques applied on the shaft. • Calculate the maximum and minimum stresses on section CD. • Calculate the shaft diameter on section AB and BC for the given allowable shear stress of these sections. TD GGGK (di,do) TC d2 TB TA L3. Figure 2: A Shaft loaded with different torques

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Study Resources v Textbook Solutions Engineering & Technology / Mechanical Engineering / A solid transmission shaft is 3.5 inch in dia Question Answered step-by-step A solid transmission shaft is 3.5 inch in diameter. It is desired to replace it with a hollow shaft of the same material and same torsional strength but its weight should only be half as much as the solid shaft. Find the following a. Outside diameter of the shaft b. Inside diameter of the shaft c. The volume of hollow shaft per foot length d. The shearing stress of hollow shaft if it is used to transmit 150KW at 600 rpm, Mpa Engineering & Technology Mechanical Engineering Answer & Explanation Solved by verified expert O *You c
Two shafts, 1.67 ft apart, are connected by an open belt. The input shaft has a speed of 350 rpm and the output shaft should be capable of running at speeds of 950 rpm, 650 rpm, 450 rpm, 250 rpm, and 150 rpm. If the diameter of the smallest pulley on the driven shaft is 2 inches, calculate the length of the belt and the diameters of each pulleys attached at the shafts.
Q2:- In an epicyclic gear train shown in the Fig. b, the internal wheels A and F and the compound wheel C,D rotate about the axis O. The wheels B and E rotate on pin fixed to the arm L. The wheels have the same pitch and the numbers of teeth are: B and E 18, C 28 and D 26. If the arm L makes 150 rpm clockwise, find the speed of F when (a) the wheel A is fixed; and (b) the wheel A makes 15 rpm counterclockwise. F D.
For the steel shaft shown in Fig. Draw a torque diagram for the shaft. 30 kN-m 15 kN-m 5 kN-m B. 10 kN-m 40 kN-m
1.The pitch circle diameter of the smaller of the two spur wheels which mesh externally and have involute teeth is 100mm.The number of teeth are 16 and 32.The pressure angle is 20° and the addendum is 0.32 of the circular pitch.Find the length of the path of contact of the pair of teeth
A helical gear of 10 inches pitch diameter has a helix angle of 25 degree, and there are 35 teeth. The gear transmits 40 hp and rotates at 450 rpm with a normal pressure angle of 20 degrees. Find the value of the normal modules in mm.
The diagram below shows a shaft with spur gear (B), bevel gear(D), and two supporting bearings (A and C). All dimensions are in millimeters and all shoulder fillets (at points where diameter changes) have a radius of 4.4 mm. The pressure angle for the spur gear at B is 16 °. The pressure angle for the bevel gear at D is 18° and the bevel angle is 45°. Note that the shaft is designed so that only bearing A takes thrust. The shaft is made of steel with Su= 1060 MPa. All the critical surfaces are ground. The shaft rotates at 1820 rpm. A motor with a power of 650 kW is connected at the bevel gear through another bevel gear. This drives the shaft. A load is connected through another spur gear at the output spur gear at B. The standard deviation on the power is 60 kW. (a) Determine the forces acting on the gears. Recall that for a spur gear, the relation between the tangential component of the force and the radial component of the force and the pressure angle is given by F₁ = F₂.tan(o). For…
The number of teeth on the driving sprocket chain is 50, used to change up of speed from 500 r.p.m. to 850 r.p.m. Find the number of teeth on the driven sprocket. If the pitch circle diameter of the driven sprocket is 350 mm and center to center distance between the two sprockets is 1000 mm, determine the pitch and length of the chain.
The minimum required length of a key for a gear carrying 20000 lb.in of torque if it is mounted on a 3.75 in diameter shaft is most likely: Consider SAE 1018 as the key material. 1.20 3.5 1.53 1.45
Two shafts, each carrying a four-stepped pulley, are to be connected by a crossed belt. The driving shaft is to turn 150 rpm while the driven shafts is to turn 50, 150, 250 and 600 rpm. The smallest step of the driver is 10 in. in diameter. Find the diameters of all steps. Please Show a clear and detailed solution (with illustration). Thank you!
An aircraft engine drives a propeller through a reduction drive as shown in fig.2. The gears 1, 2, 3 and 4 have 48, 27, 45 and 120 teeth respectively. Find the propeller speed in magnitude and direction if the engine makes 2500 rpm
QUESTION 2 A shaft rotates at 300 rpm. 1). If it carries a spur gear that delivers 5 hp to a mating gear and the spur gear has the diametrical pitch of 10, pressure angle of 20°, and 80 teeth, determine a). The resultant force exerted on the shaft = Ib 2). If it carries a sprocket that delivers 4 hp to a mating sprocket and the sprocket has the pitch diameter of 6", determine b). The force exerted on the shaft Ib 3). If it carries a "flat-belt pulley" (Note: NOT V-Belt Drive) that delivers 8hp to another flat-belt pulley and the pitch diameter of the pulley is 20", determine C). The force exerted on the shaft: Ib