Q2 The constant tensions of 200 N and 160 N are ap- plied to the hoisting cable as shown. If the velocity v of the load is 2 m/s down and the angulár velocity w of the pulley is 8 rad/s counterclockwise at time t 0, determine v and w after the cable tensions have been applied for 5 s. Note the independence of the results. 200 N 160 N 300 mm 15 kg T = 250 mm 20 kg

Q2 The constant tensions of 200 N and 160 N are ap- plied to the hoisting cable as shown. If the velocity v of the load is 2 m/s down and the angulár velocity w of the pulley is 8 rad/s counterclockwise at time t 0, determine v and w after the cable tensions have been applied for 5 s. Note the independence of the results. 200 N 160 N 300 mm 15 kg T = 250 mm 20 kg

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Use work and energy to calculate the final angular velocity (e) of the 10kg bar. The bar has the initial motion shown and displaces 0 = 90°. 2m 3 radis
The strings AB and AC connect 500-g mass A to the vertical shaft BC. When the shaft rotates with a constant angular velocity of 15 rad/s, the ball has circular motion in the horizontal plane with the strings having angles of a = 55° shown in the figure. Find the tension forces at the strings AB and AC. B 500g 400 mm 400 mm
Q-4) The rod, having a weight of 16N and a length of 2.5m, contains a joint at O which is 0.5m distant from point B. The other end of the rod is attached to a 2,5 m- 0,5 m spring that is compressed by 4cm A with Ks= 250N/cm. At this moment the rod is horizontal. When released; calculate it's angular velocity (passing by the vertical position) and reaction forces at the joint 0.
2/135 As the hydraulic cylinder rotates around O, the ex- posed length 1 of the piston rod P is controlled by the action of oil pressure in the cylinder. If the cyl- inder rotates at the constant rate 0 = 60 deg/s and 1 is decreasing at the constant rate of 150 mm/s, calculate the magnitudes of the velocity v and ac- celeration a of end B when 1 = 125 mm. Ans. U = 545 mm/s, a = 632 mm/s² 375 mm 0 Problem 2/135 B
The rope that is wound around a drum wheel lifts the bucket, as shown in the figure. If the angular displacement of the wheel is given by the expression 0 = (0.7t³ + 1t) rad, where t is in seconds, determine the velocity of the bucket (in ft/s) when t 4.4 s. = 0.75 ft
The 2-1b spool slides along the smooth horizontal spiral rod, r = (20) ft, where is in radians, as shown in (Figure 1). At the instant = 90°, its angular rate of rotation is constant and equals 0 = 4 rad/s. Figure 8 = 4 rad/s 1 of 1 P Determine the horizontal tangential force P needed to cause the motion. Express your answer in pounds to three significant figures. IVE ΑΣΦ ↓↑ vec P= 6.244 Submit Previous Answers Request Answer X Incorrect; Try Again; 5 attempts remaining ? lb
The slider P can be moved inward by means of the string S as the bar OA rotates about the pivot 0. The angular position of the bar is given by 0 = 0.4 +0.12t+ 0.06t³, where 0 is in radians and t is in seconds. The position of the slider is given by r = 0.8 0.1t 0.05t2, where r is in meters and t is in seconds. Determine and sketch the velocity and acceleration of the slider at time t = 2 s. Find the angles a and ß which v and a make with the posi- tive x-axis. S 0 Problem 2/144 رفع جك
The rod OA rotates clockwise at a constant angular velocity of 0 = (3) rad -. Two pin-connected slider block, located at B, move freely on OA. The curved rod is described by the equationr = (250 · (8 - cos 0)) m. Hint: 1. Remember clockwise rotation is negative velocity. A d3 d1 d2 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value 01 130 degrees di 0.45 m d2 dz 0.2 m 0.325 m Using cylindrical components, a. Determine the cylinders's radial and transverse components of velocity at the instant shown, vr and b. Determine the cylinders's radial and transverse components of acceleration at the instant shown, a, and ag. c. Determine the cylinder's magnitude of the velocity at the instant shown, v d. Determine the cylinder's magnitude of the acceleration at the instant shown, a
The bar AB is uniform and has a mass of 50.0 kg. At the moment shown, the rod has an angular velocity of 4.00 rad/s and spring is stretched by 0.30 m. The force constant of the spring is 25.0 N/m.a) Determine whether or not the bar will reach the horizontal position.b) If the bar becomes horizontal, calculate its angular velocity at that position. If not, calculate the angle the bar makes with the horizontal when it comes to rest momentarily.
1. The slotted link is pinned at 0, and as a result of the constant angular velocity é = 6 rad's it drives the peg P for a short distance along the spiral guide r = (0.6 0) m where e is in radians. When e = 80 deg, Find: a. Find e, é, ë,r,r, ř. (in radians) b. The radial components, transverse components, and magnitudes of the velocity [4maeie). - The radial components, transverse components, and magnitudes of the acceleration of P at the instant. asks). %3D 0.8 m r=0.6 0 ô =6 rad/s
Link BC (of length 0.47 m) is pin connected at the fixed point C and makes an angleof ⍬ = 51° with the vertical. This link is connected to the vertical link AB (of length0.3 m) and point A is also the axle of a wheel of negligible size that is moving alonga circular track of radius r =2.3 m. If the speed of A is constant and VA = (-2.59)im/s, which one of the following statements is correct? (In the followingstatements, wAB and wBC denote ⍵AB and ⍵BC respectively, where both are definedpositive in the k-direction and given in rad/s, and A denotes the magnitude of pointA's acceleration in m/s2) 1) wAB=0; wBC=0; aA=02) wAB=6,99; wBC=-7.09; aA=03) wAB=8.63; wBC=0; aA=04) wAB=8.63; wBC=0; aA >0 5) wAB=6.99; wBC=-7.09, aA>0
The strings AB and AC connect 500-g mass A to the vertical shaft BC. When the shaft rotates with a constant angular velocity of 15 rad/s, the ball has circular motion in the horizontal plane with the strings having angles of ? = 55° shown in the figure. Find the tension forces at the strings AB and AC.