Q2) T= (50-20) 38²) A horizontal distance of (500 m) must be lay out with a steel tape, length of the steel tape Toolounder standard conditions is (30 m). Field conditions indicate that standard conditions apply except the measured temperature is 50 °C and applied tension 120'N. Determine the correct horizontal distance to be laid out, if Cs ripas (P-P)L. AE TS (120-50)3 The standard temperature20 °C. 0.02*21* Coefficient of thermal expansion of steel tape = 11.6x10-6 °C_ 005 Standard tension = SON W 0.05 kg/m -w Mass of the tape 2p² = 05)Modulus of elasticity (E) = 210*106 N/m2 (120) Cross-sectional area of the tape = 0.02 cm² O -2.4.

Q2) T= (50-20) 38²) A horizontal distance of (500 m) must be lay out with a steel tape, length of the steel tape Toolounder standard conditions is (30 m). Field conditions indicate that standard conditions apply except the measured temperature is 50 °C and applied tension 120'N. Determine the correct horizontal distance to be laid out, if Cs ripas (P-P)L. AE TS (120-50)3 The standard temperature20 °C. 0.0221 Coefficient of thermal expansion of steel tape = 11.6x10-6 °C_ 005 Standard tension = SON W 0.05 kg/m -w Mass of the tape 2p² = 05)Modulus of elasticity (E) = 210*106 N/m2 (120) Cross-sectional area of the tape = 0.02 cm² O -2.4.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4Iven: Ex : -533 x10 Ex: -533 x/0-6 67x10-6 Yx, = -l626 x /0-b E : 30 x/0 psi Y: ,30 Find: Stress Components on face +45° from X -axis.
Q. Mohr. Method.
2. WHAT IS THE MAXIMUM Pt Ре ↓ O O O 20 dia mm BEARING STRESS : 100 MPa SHEAR STRESS: 150 MPa STRESS: 280 MPa SAFE LOTAD? 130mm ->P I -P 25mm
Use controll point for correction
4) For the two bars for which one bar is subjected to a so N load, and cross- sectional area of 200 mm. Find the load of the ofther bar when its allowable stress does not exceed 70 percent that of Bar 1 and whose cross-sectional ar ea is 300 mm². a. 52.5 kN 6. 525 N C. 5250 N d. 52, 000 N
Problem 14 , 3 parts ....plz solve all parts I vll upvote
A line is recorded as 472.90 m. long. It is measured with a 0.65 kg. tape which is 30.005m. long at 20°C under a 50 N pull supported at both ends. During measurement, the temperature is 5°C and the tape is suspended under a 75 N pull. The line is measured on 3% grade. Modulus of elasticity of the tape is 200 GPa, cross-sectional area of the tape is 3mm? and the coefficient of linear expansion is 0.000016m/°C. a. Compute the actual length of the tape during measurement. b. Compute the total error to be corrected for the inclined distance c. What is the true horizontal distance.
ve similar El= 4.85x10° kips.in- 8 If Q1= - 4 kips and Q2=7 kips, find A, in inches using the flexibility method. O2,D2 200 300" 300"
A base line was measured with a steel tape of designated length 30 m at 20°C at a pull of 100 N. The measured length of base line was 1543 m. The field temperature was 31.5°C and the pull applied was 130 N. Find the correct length of base line. The cross-sectional area of tape is 2 mm², coefficient of thermal expansion of steel is 2.5 x 10-8 °C-1 and E = 2 x 105 N/mm².
The measured length of two points along the ground was recorded as 550.00 m. The 50 m tape is of standard length at temperature 15 °C and a pull of 40N. During measurement, the temperature reading was 36'C and the tape was supported at both ends with an applied pull of 48N. By raising the tape, sag was also observed. The cross sectional area is 6.50 mm² and the modulus of elasticity is 200 GPa. The tape has a unit mass of 0.07 kg/m. (K=0.0000116/"C) Determine the corrected distance in meters. NOTE: Units are not required. Round-off to two decimal places.
Q2) for the fig find design strength moment, bean use fo = 28 Mpq Can be applied бус 420 мра 6n 220m 28 29 12 33m DES leo nw. lookin
The standard length of a tape is 100m having a weight of 1.2kg with the standardtemperature of 20 C and standard pull of 5.5kg. The young modulus of elasticity of thetape is 200GPa, cross sectional area is 2.8mm? and the coefficient of linear expansionis 0.0000116/°C. Determine the normal tension of the tape.