Q2) Given a two-input neuron with the following parameters: p=[5],w = [32], b = 1.2 W= 6 calculate the neuron output for the following transfer functions: i. A symmetrical hard limit transfer function ii. A saturating linear transfer function iii. A hyperbolic tangent sigmoid (tansig) transfer function

Q2) Given a two-input neuron with the following parameters: p=[5],w = [32], b = 1.2 W= 6 calculate the neuron output for the following transfer functions: i. A symmetrical hard limit transfer function ii. A saturating linear transfer function iii. A hyperbolic tangent sigmoid (tansig) transfer function

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

ii. An LVDT has a maximum core motion of ±1.5 cm with a linearity of ±0.3 % over that range. The transfer function is 23.8 mV/mm. If it is used to track a motion from -1.2 cm to +1.4 cm, what is the expected output voltage? Further, calculate the maximum linearity deviation of the transfer function.
Solve in digital format 1.- Describe in your words the definition of bandwidth.2.- Describe the definition of bandwidth of a system.3.- Describe the definition of bandwidth of a signal4.-What is the function of a filter?
How to calculate the transfer function of this? How do we write the three non touching loops?
Problem 3 A linear delta modulator is designed to operate on speech signals limited to 3.4 kHz. The specifications of the modulator are as follows: > Sampling rate = 10fxyquiatɔ where fxyqpuine is the Nyquist rate of the speech signal. > Step size A = 100 mV. The modulator is tested with a 1-kHz sinusoidal signal. Determine the maximum ampli- tude of this test signal required to avoid slope overload.
solve part (a ) only . Determine the system transfer function
Signal and system problem.plz solve every step with formula
(c) LVDT will be used to measure work piece motion from -1.2 cm to 1.4 cm , the static transfer function (sensitivity) =23.8 mV/mm find: 1) The voltage output range. 2) The position when V,= -300 mV. 3) If the resolution changed to 0.5 mm what will be the resolution of the output voltage.
The pulse function usually indicates an "on-off" switch and is usually represented in terms of the difference of two step functions. Given a pulse function in image a)Write ℎ(?) as a piecewise function and sketch the graph of ℎ(?). b) Determine the transfer function ?(?)
A system is described by transfer function H(s). The frequency response for such system is shown in Figure 1.2 (attached). Use the frequency response data to perform the following tasks: (i) Obtain the gain and phase margins. (ii) Design a lead compensator to increase the phase margin to at least 33°. (iii) Design a lag compensator to increase the phase margin to at least 43°.
What is the transfer function of a system that has poles and zeros indicated in the figure and whose gain constant is K = 4? A ? B? C? D?
consider the following higher order transfer function find an approximate first order plus time delay model using skogestad half rule, the overall time constant = ? overall time delay= ?
a) Consider the system shown in Figure 3(a). An input signal vm(t) is multiplied by a complex exponential signal e10nt The output signal v,(t) is fed into a low pass filter (LPF) with cut-off frequency wc. The input signal Vm(@) and the output signal V.(@) are as shown in Figure 3(b) and (c), respectively. i. Write the mathematical equation for signal in Figure 3(b). ii. Sketch signal, V,(@). iii. Based on the given V, (w), write the mathematical expression of the LPF, H(@) and state its cut off frequency, wc. iv. Sketch the output of LPF, V(@), if the cut off frequency of LPF is 10. v:(t) LPF Vm(t) vo(t) H(@) ej10nt (а) |Vm (@)| IV,(@)| 10 8 6. 3 -20715T-10T-5n 5n 10n 15n 20n -57 (b) Figure 3