Answered: Q2/ Determine the magnitude and…

Name: Q2/ Determine the magnitude and direction of a force (P), ifthe horiz
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Q2/ Determine the magnitude and direction of a force (P), ifthe horizontal and vertical components are (30N) and (50N)respectively?

Engineering

Mechanical Engineering

Q2/ Determine the magnitude and direction of a force (P), if the horizontal and vertical components are (30N) and (50N) respectively?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.55P: The force R is the resultant of P and 0. Determine Q and the angle .

See similar textbooks

Related questions

Q: please help with following problems, i have attached my figure (a) Calculate the amount of heat tr...

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for yo...

Q: At the proportional limit, a 22 mm thick 75 mm wide bar elongates 6.3 mm under an axial load of 482 ...

Q: A power cycle operates between two thermal reservoirs at 1200 K and 400 K, respectively. For each of...

Q: Determine time required/pass

A: Given; In a surface broaching process, Broach pitch=6 mmand Cut per teeth= 0.05 mmIt is used fo...

Q: Please solve and show your solution on a paper with units in every proceedure. Determine the pressu...

A: given; pressure(P)=?specific gravity of seawater(SG)=1.02descends(h1)=305ft =106....

Q: 1. How to maintain the efficiency of the centrifugal pump ? 2. what is specific speed, and what is i...

A: A hydraulic pump is a device that is used to increase the level of water from the lower head to the ...

Q: Define the given terms related to mechanical properties of materials. 1. Nanoindentation 2. Neckli...

A: Nanoindentation:- it is a technique developed in the mid -70s of the last century to measure the ela...

Q: Q6. The spring of constant k is unstretched when the slider of mass m passes position B. If the slid...

Q: • A 850-lb force is applied to a o.15-in. diameter nickel wire having a yield strength of 45,000 psi...

A: Find the stress and determine the wire will deform plastically or not.

Q: Determine the force P that will give the body shown in the figure below an acceleration of 6 ft/s^2....

Q: g) Determine the useful work that the Carnot engine produces. (h) Verify the result in (g) by dete...

Q: Gardeners are holding a nozzle at the end of a hose to wash way mud from landscaping. The nozzle exi...

Q: If one node is observed at a frequency of 1000 RPM, during a whiring of a simply supported long slen...

Q: Homework: Draw S.F.Ds and B.M.Ds for the following beams:

A: Calculate the reaction and moment at the support, RB=6×6+12×6×18-6RB=36+36RB=72 kN MB=6×6×3+12×6×18...

Q: F6-1L Hbe beam is sobjoctad to a bending mument af H= 50 LN mL delemine the matimum bending iress In...

Q: Given the equation of the curve : y = 0.01(1600 – x^2). 1. Find the area bounded by the curve and th...

Q: A particle travels along a straight line with a speed ?? = (0.5t^3 − 8t) m/s, where t is in seconds....

Q: Enthalpy is a state function. We can think of the first law of thermodynamics as an energy balance s...

A: Enthalpy is the sum of internal energy and product of pressure and volume. It is property of system....

Q: fill out density chart

A: Given: For aluminium: mass→m=0.0122 Kg length→L=0.0222 m Diameter→D=0.016 m Hence volume of the alim...

Q: Given a specified level of significance the absolute value of the critical value will be smaller for...

A: A one-tailed test is set up to show that the sample mean would be higher or lower than the populatio...

Q: Mechanical System Design Home Work 2 PISTON DESIGN Q2: Design a cast iron trunk type piston for a si...

Q: Answer clearly and concisely. how does your computations go when for example all needed info are de...

A: During solidification, fluid movement is common, which disrupts the above-mentioned solute diffus...

Q: A car moves in a straight line such that for a short time its velocity is defined by v= (3t^2+ 2t) m...

A: Rate of change of velocity is known as acceleration. Rate of change of displacement is known as velo...

Q: Explain in your own words: In the study of fluid phenomena, how does Newton's Law of Viscosity affec...

A: According to Newtonian law of viscosity the shear stress is directly proportional to the velocity gr...

Q: From a height of 70 ft above ground, an item is flung vertically upward. The object's starting veloc...

A: Given: h = 70 ft u = 30 ft/s g = -32.2 ft/s2

Q: Draw stress-stain curve with plastic and elastic deformation

A: To draw : stress-stain curve with plastic and elastic deformation

Q: Give an example problem with this topic:Dynamic Equilibrium in Translation (Analysis as a Rigid Body...

Q: HW) Can we create a hydraulic hand jack that can be used to lift heavy weights (say 1000 KN) by simp...

Q: punch diameter (in mm) and punch force

A: Given; Determine; Die diameter ? Punch diameter ?Where, Hole is pierced,ϕ=25 mm Thick steel shee...

Q: 5. For the following pin-collected link assembly, link AO is pinned at point O, and moves with angul...

Q: A horizontal water jet from a nozzle of constant exit cross section impinges normally on a stationar...

A: Necessary force increase by factor of 25

Q: In a surface broaching process, a broach having 5 mm pitch and cut per teeth 0.05 mm is used for red...

Q: %3D

Q: A pipe carrying steam at 3.0 MPa has an outside diameter of 450 mm and a wall thickness of 10 mm. A ...

Q: Uad an r sheets Tw Pand 0 edshown in Fig to an ac reecton Knowng that the connecton isn eguitrum and...

Q: -2 Andrei is flying an SR-71 horizontally at 1,000m/s at an altitude of 20,000m where the speed of s...

Q: 1. The wheel starts rotating from rest, 4) if its angular velocity W as a function of angular positi...

Q: e force in each member of the truss shown.

A: To find Force in each member of the truss

Q: 7. A steel tube with the cross section shown carries a torque T=67.5 k-in. The tube is 6 ft long and...

A: The maximum shear stress is, τ = 3.6 ksi. The maximum angle of twist is, θ = 0.5 degrees.

Q: A horizontal water jet with a velocity of 5.4 m/s strikes a moving object with a velocity of 0.8. If...

Q: When there is heat loss in a system, how can you increase the work output? a. Increase inlet T at t...

A: Answer: The correct answer is option (a).

Q: A uniform slender rod rests on a car seat as shown. Determine the deceleration a for which the rod w...

A: Given data as per question Horizontal angle =70

Q: Part A Determine the magnitude of the resultant force acting on a 7 -kg particle at the instant t = ...

Q: When motion is the normal component of acceleration is zero. rectilinear O rotational translation cu...

A: It is required to choose correct answer

Q: 3.1 For the following flow fields, determine whether the flow exists or not: (b) V = -kx/yi + k In(x...

A: Find the flow exist or not .

Q: Suppose that F1 = 19 kN. a) Determine the x and y components of reaction at pin A using scalar nota...

Q: 1. The wheel starts rotating from rest, 5) if its angular velocity @ as a function of angular positi...

Q: IDENTIFY THE NUMBER OF ATOMS (CL, C, H, and F) in the Refrigerant R50

A: Given Refrigerant R 50 To find Number of atoms

Q: To maximize production and minimize pumping costs, crude oil is heated to reduce its viscosity durin...

A: It is required to determine convection heat transfer resistance on inside of the pipe per unit lengt...

Q: An oscillating water sprinkler is operated at point A on an incline that forms an angle ß with the h...

A: Given: inclination angle→β=15° Initial srinkler water angle from verticle→θ=50° Initial velocity of...

Topic Video

Question

Q2/ Determine the magnitude and direction of a force (P), if
the horizontal and vertical components are (30N) and (50N)
respectively?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q2/ Find the resultant force for the concurrent coplanar force system, shown in figure 60° K 80N 55N 120N
Q1. Determine the resultant force and angle of the two forces as shown in figure by (Pythagorean law) and (components method the x-horizontal component and y-vertical components)? 600 N 400 N 60
Q2: The shaft S exerts three force components on the die D. Find the magnitude and coordinate direction angles of the resultant force. Force F, acts within the octant shown. F = 200 N 2 60 F 300 N F- 400 N
Answer the following. 1.) Determine the resultant force if F1 = 120 lb at 60 deg N of W, F2 = 100 lb southeast. 2.) Find the magnitude of the resultant force if F1 = 50 lb at 35 deg S of W and F2 = 40 lb at 25 deg N of W.
Q2) What is the magnitude of F; and its direction Ø „when the magnitude of the resultant force acting on the bracket is 600N directed along the positive x axis. F= 450 N F2 F- 500 N Ø=27° ,F2=622N Ø=88° ,F2=1037N Ø=42° ,F2=860 N Ø=86° ,F2=580 N
200 N 3 2 - Determine the horizontal & vertical components of the force ( 200 N)?
Q2: Determine the magnitude of the force (F) so that the resultant ( FR ) of the three forces is as small as possible. What is the minimum magnitude of ( FR) ? 30 30 400 N 500 N REDMI NOTE 9 PRO AI QUAD CAMERA
Q1. A parallel force system acts on the lever shown in figure. Determine the magnitude and position of the resultant with respect to A. 30 N 60 N 20 N 40 N 2 m 3 m 2 m 4 m
Q3b. Force vectors F1 and F2 act on body P with the resultant force vector R. The resultant force R= 350 N and the angle between R and the x-axis is of 35°. If F1 = 180 N and the angle between F1 and the x-axis is 72º, determine the angle between F2 and the x-axis. Assume coplanar vector forces and give your answer in degrees to two decimal places. F1 R F2 Body, P Answer:
1.) Find the sum of the vertical forces in pounds if F1 = 30 lb at 60 deg N of W and 50 lb at 40 deg S of E. 2.) Find the resultant force if F1 = 20 N south and F2 = 30 N west.
Q3a. Force vectors F1 and F2 act on body P with the resultant force vector R. The resultant force R = 350 N and the angle between R and the x-axis is of 35°. If F1 = 180 N and the angle between F1 and the x-axis is 72°, determine the magnitude of F2. Assume coplanar vector forces and give your answer in newtons (N) to two decimal places. F1 R F2 Body, P Answer:
Q2: Determine the resultant of the force system in next fig. Then locate it with respect to point (A). 1000 N.m K K A 10m 10m 10m 80 N 150 N 100 N (15 degrees)