Q2/ By using the power series method make a dimensional analysis for he following variables: The frictional torque of a disc T = f (disk liameter D, rotating speed N, viscosity of fluid µ, and its density p).

Q2/ By using the power series method make a dimensional analysis for he following variables: The frictional torque of a disc T = f (disk liameter D, rotating speed N, viscosity of fluid µ, and its density p).

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.13P: 5.13 The torque due to the frictional resistance of the oil film between a rotating shaft and its...

See similar textbooks

Related questions

Q: The lift of a wing, Fisft, is a function of wingspan, W, chord length, H, surrounding air density,…

A: Flift=fW,H,ρ,μ,V

Q: Dimensional analysis with Buckinham's Pi Theorem is applied to the relationship between frictional…

A: given; head lossHf=dpdxaDbρcμdvf

Q: Applying Dimensional Analysis to the human anatomy studies, it was found that the velocity, c, at…

A: It is required to perform dimensional analysis for velocity

Q: Example: The pressure difference (Ap) between two point in a pipe due to turbulent flow depends on…

A: ∆P=fV, D, μ, ρ ,e, L

Q: Q2: The moment exerted on a submarine by its rudder is to be studied with a 1:20 scale model in a…

A: This problem is related to the model and prototype similarity. for the dynamic similarity between…

Q: Consider laminar flow over a flat plate. The boundary layer thickness & grows with distance x down…

Q: The force (F) acting on a particle moving in a fluidized bed depends: the mass of the particle, it…

Q: The radius R of a mushroom cloud generated by a nuclear bomb grows in time. We expect that R is a…

Q: The bending stress o in a beam depends upon the bending moment Mand the beam area moment of inertia…

A: It is required to determine dimensionally homogeneous formula for bending stress

Q: 1. Geologists are able to discover oil deposits by measuring variations on the gravitational…

A: geologists are able to discover oil deposits by measuring variations on the gravitational…

Q: 5.5 An automobile has a characteristic length and area of 8 ft and 60 ft²', respectively. When…

A: Answer: The properties of air at sea level are: P = 0.00238 slug/ft3μ =3.72x10-7 slug/ft.s The…

Q: The speed of sound c in an ideal gas is known to be a function of absolute temperature T, universal…

A: The complete derivation is attached as an image.

Q: Power generated by a propeller operating in the air (P); it depends on the mass density of the air…

Q: List the three primary purposes of dimensional analysis.

A: Dimensional Analysis is a mathematical technique that makes use of the study of dimensions as an aid…

Q: a) i. Define dimensional constant. ii. Define non-dimensional variable. b) When a liquid in a beaker…

A: We have given

Q: Task 2 Evaluate the use of dimensionless analysis using the Buckingham Pi Theorem for a given fluid…

Q: The force, F, acting on a billboard due to wind depends on it length, l, height, h, the modulus of…

A: As it is given in the question that the force (F) depends in l, h, E, and γa. Here are the…

Q: An automobile has a characteristic length and area of 8 ft and 60 ft, respectively. When tested in…

A: The properties of air at sea level are: The Reynolds number is The drag coefficient is Velocity…

Q: The quantities viscosity u, velocity V, and surface tension Y may be combined into a dimensionless…

Q: P5.37 The volume flow Q through an orifice plate is a function of pipe diameter D, pressure drop Ap…

Q: How can I use dimensional analysis to show that in this problem both Froude's number and Reynold's…

Q: MLT The resistin, .orce (F) of a supersonic plane during flight can be considered as dependent upon…

Q: Q3: The power output (P) of a marine current turbine is assumed to be a function of velocity U,…

A: Given that The power output (P) of a marine current turbine is assumed to be a function of velocity…

Q: When a liquid in a beaker is stirred, whirlpool will form and there will be an elevation difference…

Q: The drag FD of the golf ball is affected by the speed V of the ball, the diameter d of the ball, the…

Q: The differential equation for small-amplitude vibrations y(r, f) of a simple beam is given by a*y +…

A: Given: The beam material density is ρ. The cross sectional area is A. The area moment of inertia is…

Q: A model submarine with a length of T = 6.0 m is to be tested in a laboratory wind tunnel using air.…

Q: From Fourrier's law, the rate of heat transfer in plane surfaces is described by: Q = /(k, A, AT, x)…

A: The first step is to identify the dimensional variable, the non dimensional variable and the…

Q: The pressure drop AP in flow through pipes per unit length is found to depend on the average…

Q: The speed of sound c in an ideal gas is known to be a function of the ratio of specific heats k,…

A: To determine: develop a functional relationship between the given parameters. There are a total of…

Q: The Ekman number, important in physical oceanography,is a dimensionless combination of μ , L , ρ ,…

A: The Ekman number can be represented as follows: E=fμ,L,ρ,Ω

Q: A- The power produced from a pump (P) is fun (Hon of flow (@), pressure drop (P), Density of fluid…

Q: VisCosity, odel tests run in a laboratory using water in a 0.2-ft-diameter pipe yield the Ty vs. Q…

Q: Q2/ By using the power series method make a dimensional analysis for the following variables: The…

Q: Dimensional analysis with Buckinham's Pi Theorem is applied to the relationship between frictional…

Q: Suppose we know little about the strength of materials butare told that the bending stress σ in a…

A: Since the bending stress proportional to half the thickness of the beam, we can state that…

Q: Under a laminar flow, the liquid flows through small holes. It has a triangular cross-section, width…

A: Given that ; Volumetric flow rate Q of the flow is a function of viscosity μ ,pressure reduction…

Q: A prototype automobile is designed for cold weather inDenver, CO ( - 10 ° C, 83 kPa). Its drag force…

A: First assemble the necessary air density and viscosity data: Denver:…

Q: The volume flow Q through an orifice plate is a function ofpipe diameter D , pressure drop D p…

A: Q is the function of (D, ∆P, ρ, μ, d) Where, Q is the volumetric flow rate D is the pipe diameter…

Q: The drag of a sonar transducer is to be predicted, based on wind (Air) tunnel test data, The…

Q: The lift of a wing, Fit, is a function of wingspan, W, chord length, H, surrounding air density, p,…

Q: The lift of a wing, Fug, is a function of wingspan, W, chord length, H, surrounding air density, p,…

A: For solution refer below images.

Q: The spin rate of a tennis ball determines the aerodynamic forces acting on it. In turn, the spin…

A: Write the dimensional functional relationship. τ=fv, ρ, μ, D, ω, hf Write the basic dimensions of…

Q: O The power, W, generated by a certain windmill design depends upon its diameter, D, the air…

Q: The lift of a wing, Fift, is a function of wingspan, W, chord length, H, surrounding air density, p,…

A: Given: Lift of the wing is the function of the W, chord length H, air density ρ, viscosity μ and…

Q: The pressure drop across a short hollowed plug placed in a circular tube through which a liquid is…

Q: Dimensional analysis is to be used to correlate data on bubble size with the properties of the…

Q: Q3: The power output (P) of a marine current turbine is assumed to be a function of velocity U,…

A: Data given- Power output P is a function of U,L,w,ρ,v

Question

Q2/ By using the power series method make a dimensional analysis for
the following variables: The frictional torque of a disc T = f (disk
diameter D, rotating speed N, viscosity of fluid µ, and its density p).

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

5.13 The torque due to the frictional resistance of the oil film between a rotating shaft and its bearing is found to be dependent on the force F normal to the shaft, the speed of rotation N of the shaft, the dynamic viscosity of the oil, and the shaft diameter D. Establish a correlation among these variables by using dimensional analysis.
Q2/ By using the power series method make a dimensional analysis for the following variables; The frictional torque of a disc T- f(disk diameter D. rotating speed N, viscosity of fluid u, and its density p).
1. The thrust of a marine propeller Fr depends on water density p, propeller diameter D, speed of advance through the water V, acceleration due to gravity g, the angular speed of the propeller w, the water pressure 2, and the water viscosity . You want to find a set of dimensionless variables on which the thrust coefficient depends. In other words CT = Fr pV2D² = fen (T₁, T₂, ...Tk) What is k? Explain. Find the 's on the right-hand-side of equation 1 if one of them HAS to be a Froude number gD/V.
The viscous torque T produced on a disc rotating in a liquid depends upon the characteristic dimension D, the rotational speed N, the density pand the dynamic viscosity u. a) Show that there are two non-dimensional parameters written as: T and a, PND? b) In order to predict the torque on a disc of 0.5 m of diameter which rotates in oil at 200 rpm, a model is made to a scale of 1/5. The model is rotated in water. Calculate the speed of rotation of the model necessary to simulate the rotation of the real disc. c) When the model is tested at 18.75 rpm, the torque was 0.02 N.m. Predict the torque on the full size disc at 200 rpm. Notes: For the oil: the density is 750kg/m² and the dynamic viscosity is 0.2 N.s/m². For water: the density is 1000 kg/ m² and the dynamic viscosity is 0.001 N.s/m². kg.m IN =1
Q2/ A car wheel is supposed to be travelling at a speed of 80 mile per hour in the air. A scaled model (1:4) is tested in water instead of air and is supposed to have dynamic similarity. a) Determine the model speed in water b) then find the force ratio of the model to prototype if you know that: (pair = 1.22 kg/m³, µair = 1.78 x 10- 5 N.s/m?, Pwater 998 kg/m², µwater = 0.001 N.s/m²).
b) When a liquid in a beaker is stirred, whirlpool will form and there will be an elevation difference h, between the center of the liquid surface and the rim of the liquid surface. Apply the method of repeating variables to generate a dimensional relationship for elevation difference (h), angular velocity (o) of the whirlpool, fluid density (p), gravitational acceleration (g), and radius (R) of the container. Take o, p and R as the repeating variables.
Force F is applied at the tip of a cantilever beam of length L and moment of inertia I Fig. . The modulus of elasticity of the beam material is E. When the force is applied, the tip deflection of the beam is z d.Use dimensional analysis to generate a relationship for zd as a function of the independent variables. Name any established dimensionless parameters that appear in your analysis
The force (F) acting on a particle moving in a fluidized bed depends: the mass of the particle, it velocity, the density the fluid and the gravitational acceleration. Find the relation between these variables using dimensional analysis. With Rayleigh's method
Q.2. The force of impeller depends on the volumetric flowrate of fluid (Q) through the pipe of diameter (d) ,fluid density and viscosity , rotation of impeller (N). By using the dimensional analysis (Buckingham's Theorem), find the relation between the above parameters.
When a liquid in a beaker is stired, whirlpool will form and there will be an elevation difference h, between the center of the liquid surface and the rim of the liquid surface. Apply the method of repeating variables to generate a dimensional relationship for elevation difference (h), angular velocity (@) of the whirlpool, fluid density (p). gravitational acceleration (2), and radius (R) of the container. Take o. pand R as the repeating variables.
Q4: Use dimensional analysis to show that in a problem involving shallow water waves (Figure 1), both the Froude number (Fr = and the Reynolds number (Re pch. are relevant dimensionless parameters Fr = f (Re). The wave speed c of %3D waves on the surface of a liquid is a function of depth h, gravitational acceleration g, fluid density p, and fluid viscosity u. P. u Figure 1
How can I use dimensional analysis to show that in this problem both Froude's number and Reynold's number are relevant dimensionless parameters? Problem: Here shallow waves move at speed c. The surface of the waves is a function depth (h), gravitational accelaration is g, densisty is p and fluid viscosity is μ. I need to get the parameter in the form in the image. Please help :)