Q2/ A tube bank 10 rows high and 7 rows deep with Sp-Sn= 60 mm. Uses in-line arrangement of 30 mm diameter tubes and tube length of 1m. Air with upstream conditions of Too =27 °C and v= 15 m/s in cross flow over the tubes, while a tube wall temperature of 100 °C is maintained by steam condensation inside the tubes. Determine the temperature of air leaving the tube bank.

Q2/ A tube bank 10 rows high and 7 rows deep with Sp-Sn= 60 mm. Uses in-line arrangement of 30 mm diameter tubes and tube length of 1m. Air with upstream conditions of Too =27 °C and v= 15 m/s in cross flow over the tubes, while a tube wall temperature of 100 °C is maintained by steam condensation inside the tubes. Determine the temperature of air leaving the tube bank.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.20P

See similar textbooks

Similar questions

Write legibly, provide manual step by step solution, and diagram for below given problem. At an average temperature of 110°C, hot air flows through a 5m pipe with outside diameter of 80mm and pipe thickness of 1cm. The temperature of the tube along its entire length is 240°C. If heat transfer if 650 W, find the convective film coefficient, W/m² - C.
7. Engine oils enter a 20 mm diameter tube at a temperature of 22°C and a flow rate of 0.8 kg/s. If the tube surface temperature is maintained at 150 °C, find the outlet temperature for a tube that is 10 m long as well as one that is 80 m long. Estimate the mean temperature to be 77 °C. Answer questions 7.1 and 7.2: 7.1. What is the outlet mean temperature, in °C, for the pipe that is 10 m in length? 7.2. What is the outlet mean temperature, in °C, for the pipe that is 80 m in length?
Fluid is flowing through a 20 mm inside diameter and 25 mm outside diameter brass tube at no leaking with temperature at 65℃ and length of 10 m. Surface conduction of hot fluid is 5.2W/(m^2℃) and thermal conductivity of brass is 12.84W/(m℃). Brass tube is covered by silica of 6 mm thickness with thermal conductivity of 13.84W/(m℃) . Outside of it, is a fluid with 45℃ with surface conductance of 3.2W/(m^2℃). Find the heat transfer from the hot fluid with temperature of 65℃ to fluid with temperature of 45℃.
Fully developed conditions are known to exist for water flowing through a 50-mm ID tube at 0.02 kg/s and 27°C. What is the maximum velocity of the water in the tube? What is the pressure gradient associated with the flow?
Air (pressure 1 atm) enters a circular pipe 5 cm in diameter at 20 °C with an average speed of 5 m/s. The tube wall is maintained at a constant surface temperature of 160°C, and the mean outlet temperature is 80°C. Estimate the length of the tube. Mainly, I also need the solution from concepts of how the heat flow behaves in the system, it can be with a diagram.
. Oil enters a 1.25-cm diameter,3-m long tube at 38°C. The tube wall is maintained at 66°C, and flow velocity is 0.3 m/s. What is the total heat transfer to the oil and oil exit temperature? Assume an exit temperature of 50°C. Temperature (°C) p(kg/m³) u (kg/m sec) Cp J/hg °C) k(W/m °C) 0.210 0.0725 0.0320 40 0.144 867.05 864.04 1964 60 2047 0.140 80 852.02 2131 0.138
Refrigerant-134a is being transported at 0.08 kg/s through a Teflon tube of inside diameter D; = 20 mm and outside diameter Do = 25 mm, while atmospheric air at V = 28 m/s and 300 K is in cross flow over the tube. What is the heat transfer per unit length of tube, in W/m, to Refrigerant-134a at 230 K? q' = i W/m Use Hilpert correlation to estimate the external heat transfer coefficient, and please state ALL assumptions.
Water at 27°C flows with a mean velocity of 1 m/s through a 1 km-long pipe of 0.25 m inside diameter. Answer the following: a. Is the flow hydrodynamically fully developed? Support your answer with calculations. b. Is the flow thermally fully developed? Support your answer with calculations. c. What is the pressure drop over the pipe length, if the pipe surface is smooth? (Ans: 0.289 Bar) d. What is the pump power requirement, if the pipe surface is smooth? (Ans: 1.42 kW)
A square isothermal chip is of width 5mm on a side mounted in a substrate such that its side and back surfaces are well insulated, while the front surface is exposed to the flow of coolant at 15C. From reliability considerations, the chip temperature must not exceed 85C. If air is used as a coolant, h = 200W/m2. If a dielectric liquid is used as coolant, h = 3000W/m2. What is the difference in maximum allowable power through the chip between the two coolants? (answer in W) *
Merrill et al. (1965) in a series of classic experiments studied the flow of blood in capillary tubes of various diameters. The blood had a hematocrit of 39.3 and the temperature was 20°C. They measured the pressure drop as a function of the flow rate for five tube diameters ranging from 288 to 850 μm. When they expressed the measured pressure drops in terms of the wall shear stress, and the volumetric flow rates in terms of the reduced average velocity, all of the data for the various tube sizes formed, within the experimental accuracy, a single line as predicted by the Rabinowitsch equation expressed in terms of reduced average velocity. From their results they provide the following values of the Casson parameters at 20°C: τy = 0.0289 dynes cm−2 and s = 0.229 (dynes s cm−2)1/2. Using these values for τy and s, show that the equation below for reduced average velocity provides an excellent fit to their data summarized in the following table. (Wall shear stress) τw , dynes cm-2…
Hot water (cp=4.18 kJ/kg.K, m = 2.8 kg/min) flows inside a tube (inner diameter = 9 mm, Length = 93 cm, thickness = 1.0 mm, k outer surface is 204 kW/m .What is the temperature drop of water ( C)? 40 W/m.K), if the heat flux on the tube %3D tube
A saturated steam at 410K is being transported in a pipeline (brass drawing tubing) at a rate of 1 grams/second. Pipe has inside diameter of 0.025 m . The tube is 100m long. The pressure at the entrance is 80kPa. What is the % of pressure drop? (use Perry's Handbook for the properties and constants) R = 8314J/kgmol.K; MW=18.02g/mol