Q2: A shaft is driven by a motor which exerts a constant torque while the load taken off the shaft fluctuates from zero to maximum during each revolution. If the maximum fluctuating in energy in one cycle is AE=242 N.m. Find the moment of inertia of the flywheel (1) to be mounted on the shaft so that the speed fluctuating shall not be more than 3 r.p.m. above or below a .mean speed of N=200 r.p.m

Q2: A shaft is driven by a motor which exerts a constant torque while the load taken off the shaft fluctuates from zero to maximum during each revolution. If the maximum fluctuating in energy in one cycle is AE=242 N.m. Find the moment of inertia of the flywheel (1) to be mounted on the shaft so that the speed fluctuating shall not be more than 3 r.p.m. above or below a .mean speed of N=200 r.p.m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The mass of the A gear is 10 kg and the turning radius is 200 mm. Of gear Bits mass is 3kg and the turning radius is 80 mm. When the system is stationary to gear B. Moment of 6 N.m is applied. By neglecting friction; a) The time elapsed until the angular velocity of gear B reaches 600 rpm.b) Find the tangential force from gear B to gear A.
A wheel with rotational inertia 48 kg.m2 is mounted on a fixed, frictionless axle. The angular speed of the wheel is increased from zero to 59 rad/s in 12-s. What is the average net torque/Moment in N.m on the wheel during this time interval?
A riveting machine is used for riveting sheets of 20 mm thickness. The machine is driven by a geared motor of 5 kW. The mass moment of inertia of the rotating parts of the machine attached to flywheel is found to be 10 kg- m². At the beginning of the operation, the flywheel is making 15 r.p.s. If making one rivet takes 30 KN-m of energy in 5 second, then find the reduction of speed of the flywheel
3. In a turning moment diagram, the areas above and below the mean torque line taken in order are 4400, 1150, 1300 and 4550 mm² respectively. The scales of the turning moment diagram are: Turning moment, 1 mm = 100 N-m; Crank angle, 1 mm = 1° Find the mass of the flywheel required to keep the speed between 297 and 303 r.p.m., if the radius of gyration is 0.525 m. [Ans. 417 kg]
J1. In summary, the rotational acceleration of the rollers is 44.02 rad/s2. Using the mass moment of inertia found in step 5, what is the torque required to accelerate the rollers?
2. (20%) In the rotary system as below, where tire mass m, =12 kg, axle mass m, = 3 kg, and radius r= 0.30 m. 1) The mass of all the other parts is ignorable. What is the moment of inertia J for the overall system with respect to the center? 2) What is the torque T for an external force F 25 N working on the top edge of the tire as indicated in Fig. 1, where the direction of the force is perpendicular to the radius? 3) What is the angular acceleration of the system? m, Fig 1. Tire and Wheel Rotary System
The mass of flywheel of an engine is 8 tonnes and the radius of gyration is 1.8 metres. It is found from the turning moment diagram that the fluctuation of energy is 100 kN-m. If the mean speed of the engine is 150 r.p.m., find the maximum and minimum speeds.
The turning-moment diagram for an engine consists of two isosceles triangles each with a height equivalent to a torque of 16kNm. The bases of the triangles lie between ? = 0 ? and ? = 180? , and ? = 180? and ? = 360? Sketch the turning-moment diagram and add the mean torque line. If the engine is to rotate with a mean speed of 130 rpm, calculate the following: the power developed the mass of the flywheel having a radius of gyration 1.1m to restrict the fluctuation of speed to +1.5% of the mean speed. Demonstrate which would be most effective to reduce the fluctuation of speed, a change in diameter of or a change in mass of the flywheel.
The cable spool shown at the right has a weight of 50 lbs and has a moment of inertia of .28 slug-ft^2. Assume the spool rolls without slipping when we apply a 50-lb tension in the cable. Find: friction force between the spool and the ground.
Q2/ The out - of - balance of a machine rotor is equivalent to 5 kg at 10 mm radius in one plane A, together with an equal mass at 15 mm radius in a second plane B. AB = 375 mm and the two radii are 120°. Find the mass required in third plane C at a radius of 125 mm and its angular position with respect to the given radii so that there is no resultant out - of - balance force. Find also the position of C along the axis for the residual couple to be a minimum and of this couple when the speed is 500 r.p.m.
R - m 130° A hollow wheel of mass given by m 50 kg rolls down an incline of 30° without slipping. The inner radius of the wheel is given by R = 50 mm and its thickness is given by d = 5 mm. Gravity acts down. (a) Show that the moment of inertia of the wheel is given by Ī = 138 125 kg mm². (b) Show that the linear acceleration of the wheel's centre of gravity ā is related to the angular acceleration of the wheel a via a (55 mm)a. = (c) Analyse an appropriate free-body diagram to determine the linear acceleration of the wheel's centre of gravity ā.
Q4:-A rotating shaft carries four masses 176.6 N, 137.3 N, 157 N and 117 N at radii 5 cm, 6 cm, 7 cm and 6 cm respectively. The second, third and fourth masses revolve in planes 8 cm, 16 cm and 28 cm respectively measured from the plane of the first mass (at the left end). They are angularly located at 60°, 135° and 270° respectively measured clockwise from the first mass (at the positive x-axis). The shaft is dynamically balanced by two masses both located at 5 cm radii and revolving in planes midway between those of 1st and 2nd masses and midway between those of 3rd and 4th masses. Determine the magnitude of the masses and their respective angular positions.