Q2: A 4000/400 V, 10 kVA transformer has the following constants: Primary and secondary winding resistances of 13 Q and 0.15 Q respectively Leakage reactance referred to primary is 45 Q Resistance of equivalent exciting circuit referred to primary, R0 = 12k N Reactance of equivalent exciting circuit referred to primary, X0 = 6k Q What would be the reading of the instruments when the transformer is connected for the open-circuit and short-circuit tests? Compute the voltage regulation for full load at 0.8 p.f. lagging.

Q2: A 4000/400 V, 10 kVA transformer has the following constants: Primary and secondary winding resistances of 13 Q and 0.15 Q respectively Leakage reactance referred to primary is 45 Q Resistance of equivalent exciting circuit referred to primary, R0 = 12k N Reactance of equivalent exciting circuit referred to primary, X0 = 6k Q What would be the reading of the instruments when the transformer is connected for the open-circuit and short-circuit tests? Compute the voltage regulation for full load at 0.8 p.f. lagging.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.16P: A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters:...

See similar textbooks

Similar questions

For an ideal 2-winding transformer, an impedance Z2 connected across winding 2 (secondary) is referred to winding 1 (primary) by multiplying Z2 by (a) The turns ratio (N1/N2) (b) The square of the turns ratio (N1/N2)2 (c) The cubed turns ratio (N1/N2)3
A single-phase step-down transformer is rated 13MVA,66kV/11.5kV. With the 11.5 kV winding short-circuited, rated current flows when the voltage applied to the primary is 5.5 kV. The power input is read as 100 kW. Determine Req1andXeq1 in ohms referred to the high-voltage winding.
For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.
All values of a transformer are proportional to its __________________ ___________________.
For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
Match the following: (i) Hysteresis loss (a) Can be redud by constructing the core with laminated sheets of alloy steel (ii) Eddy current loss (b) Can be reduced by the use of special high grades of alloy stl as core material.
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
Which of the following are power losses that can occur in a practical transformer (non-ideal)? copper loss O loss due to eddy currents V hysteresis loss O voltage drop due to coil material
Question:4 A Step-down transformer is given and calculate 5:1 120 V 60 Hz V2 i k2 i. Peak load and D.C. load voltage ii. D.C. Current
How do i calculate secondary current in transformer analysis
In this Center tapped transformer Find the peak voltage of V1 and V2, RMS voltage of V1 and V2, and Peak to peak voltage of V1 and V2