Q2 1- Check the following weather one way or two way 2- Calculate the design ultimate load Wu on the on the beams B3, B6 Assume slab load : Live load = 5 kN/m? Dead load = 8 kN/m2 %3D Beam size = 300x500 mm %3D

Q2 1- Check the following weather one way or two way 2- Calculate the design ultimate load Wu on the on the beams B3, B6 Assume slab load : Live load = 5 kN/m? Dead load = 8 kN/m2 %3D Beam size = 300x500 mm %3D

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.2.1P: A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The...

See similar textbooks

Related questions

Q: The continuous one-way joist slab section shown over three spans of L=5m each is loaded with…

A: Given- L=5mDL= 3kN/m2LL=2 kN/m2ρ=12 Kn/m3

Q: Calculate the depth of neutral axis

A: given Fy = 500mPa FCN = 25mPa Dia of bar = not given

Q: 03/ Find the service concentrated live load (P) that causes 1.5 MPa tension stress at the bottom…

Q: For Problems 2.45 to 2.47, compute the flexural stresses in the concrete and steel for the beams…

Q: A simply supported reinforced concrete beam is monolithically poured with slab making it applicable…

A: Given Data: tf =101 mm bf = 530 mm bw = 313 mm d = 530 mm 9-29 --- As = 5944.68 mm2 fy = 420 N/mm2…

Q: An axially loaded short square column of size 400 mm whose helical reinforcement is 4000 mm used in…

Q: The lateral load resisting system of the below building is 25 ft 25 ft 25 ft 25 ft 25 ft 25 ft 25 ft…

A: Moment frames, shear walls,dual system and braced frames are lateral force-resisting systems found…

Q: Situation #2: A properties: Width, b = 400 mm 415 MPa rectangular beam has the following Effective…

Q: 2- Calculate the design ultimate load Wu on the on the beams B1,B2, B3, B4 3.6 m 4.8 4 m Assume: DL…

Q: Using Double Integration Method, find deflection at mid-span & Slope at supports. consider the…

A: Given data: E=26211 MPa slab thickness, t= 136 mm Live load = 7.68 kN

Q: Note: please use Set B data thank you 2° M₂ A B ** 4m 2m The cantilever beam above is made up of…

A: Given: E = 70 MPa b = 250 mm h = 400 mm Required : Flexural rigidity of beam in N-mm²

Q: Calculate the depth of neutral axis of a beam of size 450x300 mm . Use M25 grade concrete and 4 no.…

A: Given data:- Beam size = 450mm x 300mm Grade of concrete fck = m25 = 25 N/mm2 Grade of steel fy =…

Q: PL MA = MB = - 8 PL Max. Ely = 192 /7

Q: A beam 200x450mm is reinforced by 2-32 mm diameter rebar. Assume cc=50mm, stirrups=10mm, fc'=21MPa…

Q: A T beam for a floor system has a slab thickness of 100mm and total depth of 550mm. bw=300mm. The…

A: Often used in civil engineering, the term "live load" refers to a load that changes over time.…

Q: A wooden plank (sp. gr. 0.5) 1 m x 1 m floats is water with 1.5 kN load o 1 m x 1m surface…

A: Step 1: Volume = 1m x 1mx 0.5m =0.5 m3 Area =1 m2 G= 0.5 P=1.5 KN

Q: Note: please use Set B data thank you W 2° M₂ A B 4m 2m The cantilever beam above is made up of…

A: Concept:- Here concept of area moment is state by two theorem Theorem 1:-- area between M/EI…

Q: Situation. A floor plan of a proposed five storey concrete building is shown. It carries the…

Q: What is the long-term deflection for dead load plus 45% permanent live load for 1 year, there is…

Q: uniformly distributed load is Ely = 8x^240x, then the beam length is

A: Given, beam loading equation, EI y = 8x2 - 40x

Q: Compute the maximum combined loads using the recommended ASDexpressions from the AISC. D = 9000 lb,…

A: Determine the maximum combined loads for AISC using the below relation: where,

Q: A carry concrete slat in the flooring of a swine housing is designed to carry swine up to 225 kg.…

Q: Design the steel reinforcement for the slab shown in the figure below, under the loading…

A: Given:- The loading on the slab is given The dead load on the slab = DL = 2 kPa = 2 kN/m2 The live…

Q: Q5/ For the floor system shown in fig. Answer the following:- 1-Determine the ultimate bending…

A: Hello dear student , as per bartrlby guidelines i solved the problem and i hope this answers is…

Q: Compute the following given a built-up I-section with dimensions of bf = 350 mm, tf = 120 mm, hw =…

A: The given figure is shown below:

Q: Homework: the slab shown in figure below is supported over a brick walls, design the slab to…

A: Given dead load =3 kn/m self weght and a service voice load =6 kn/m fc =25 MPa fy = 420 MPa

Q: A slab is supported on columns spaced at 6 m c/c apart in both directions. The sizes of the column…

Q: Q2) For the slab shown in Fig.(2),find the allowable live load for the section 1-1. Use f'c-25 MPa,…

A: Solution: Given: fc = 25 MPa fy = 350 MPa Beam dimension = 250 mm x 600 mm h = L/24 h =…

Q: For a section 6 inches wide and 14 inches deep, and a cover of 2 inches, what is the maximum safe…

A: The moment carrying capacity of the balanced beam section is M = CZ where C - Compressive force Z…

Q: For Problems 2.45 to 2.47, compute the flexural stresses in the concrete and steel for the beams…

A: compute the flexural stresses in the concrete and steel for the beams

Q: Design a rectangular reinforced concrete beam to resist service moments of 120 kNm from dead loads…

A: Service Moments Dead load (DL) = 120 kNm Live Load (LL) = 110 kNm Beam Dimension (b x d) = 0.25 x…

Q: 00 mm thick is cast monolithically with beams 250 mm wide on centers, on simple supports over a span…

A: According to given data Floor slab 100 mm thick casted monolithicallywith beams 250 mm wide and 450…

Q: A rectangular beam has b 300mm and an effective depth of 490mm. Concrete compressive strength fe =…

A: Note - factored loads are not mentioned to consider. So beam is designed for maximum moment value as…

Q: I. Calculate the safe concentrated live load at the free end for a rectangular cantilever beam 3 m…

Q: A slab is supported on columns spaced at 6 m c/c apart in both directions. The sizes of the column…

Q: Use NSCP 2015. Problems: 1.) A floor system consists of a 100mm concrete slab supported by…

Q: A three-storey bldg has interior columns spaced at 6 m apart in two perpendicular directions. Loads…

Q: Determine the governing (ASD) axial load (kN) for a column in a multistory office building using the…

Q: The standard load is 100kN. Given that n=4 and α=1, calculate EALF 80

A: Given data: Standard load is 1000 KN Certain axle load=80 KN

Q: Design a R.C.C. slab for a room measuring 4 m x 6 m. The slab is simply supported on all the four…

A: Given fck = 20 N/mm2 fy = 415 N/mm2 Load (Floor finish ) = 6000N/m2 lx = 4m ly = 6m

Q: The total dead load is 6.5 kPa and the total live load is 3.8 kPa. Use the load combination: 1.2DL +…

A: Combined Load = 1.2DL + 1.6LL = 1.2 x 6.5 + 1.6 x 3.8 = 13.88 kPa = 13.88…

Q: The dimensions for a reinforced concrete beam are given as: b = 300mm d = 400mm d’ = 75mm It is to…

Q: Compute the maximum combined loads using the recommended ASDexpressions from the AISC. D = 10,000…

A: Given:- The dead load = D = 10,000 lb The wind load = W = ±32,000 lb To determine:- The maximum…

Q: Calculate the required steel area for a reinforced concrete T-beam with an effective flange width of…

A: Moment is given by ; M = 0.87 * fy *Ast * (d - 0.42 Xu) where ; M = Ultimate moment = 1300 KN - m =…

Q: QI) The R.C slab system shown in Figure (1) supported by column line beams and carries a service…

A: GIven: LIve Load = 5 kN/m2 Dead Load = 3.5 kN/m2 Slab thickness = 200 mm Beam C/S = 300 x 175 mm…

Q: XØD Question 1 of 1 Click to see additional instructions For C30 and S420, calculate positive moment…

A: Solution:- Given details: Depth of neutral axis:

Q: Design a two way slab having a simple span of 3m x 4m. The slab is to carry a uniform live load of…

A: Slab: Slab is a structural member of which are dimension is very small as compareto other two…

Q: Design a <ir<ular slab for a roDm 5 m in diameter (effective) with simply supported edge. Total…

Q: Compute the maximum combined loads using the recommended ASDexpressions from the AISC. D = 25 psf,…

A: The given data is shown below: D=25 psfLr=20 psfW=26 psf

Q: Investigate the acceptability of the concrete beam with length (L=5400 mm) and cross-section…

A: Given Data:L=5400mmb=300mmd=500mmfc=24mpafy=400Mpa

Concept explainers

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.

Question

100%

Q2
1- Check the following weather one way or two way
2- Calculate the design ultimate load Wu on the on the
beams B3, B6
Assume slab load:
Live load = 5 kN/m2
Dead load = 8 kN/m?
Beam size
300x500 mm
%3D
B5
B6
B7
3.6 m |L
4.8
4 m
5m
5m
BI
B2
B4

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Note: please use Set B data thank you 2° M₂ A B * 4 m 2m The cantilever beam above is made up of concrete with E- 70 MPa, refer to the table below for the properties and loads for the beam: PROPERTIES LOADS SET b (mm) h (mm) w (kN/m) Mb (kN-m) A (1,3,5,7,9) 300 500 20 40 B (2,4,6,8,0) 250 400 15 45 Using area moment method, determine the following: Flexural rigidity of the beam in N-men²
In the built-up girder shown below that has an unbraced length of 25 ft. (L-25 ft) and moment gradient factor of C,-1, determine the maximum flexural design strength. E-29000 ksi Fy-50 ksi PL 25x0.6" PL 35*0.3" PL 25x0.6"
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
Compute the compressive strength of a WT 12x81 of A992 steel. The effective length with respect to the x-axis is 25 feet 7inches, the effective length with respect to the y axis is 20feet, and the effective length with respect to the z-axis is 20 feet WT12X81 A 23.9 t₁ 1.22 ly 221 d 12.5 K des 1.72 J 9.22 b₁ 13.0 y 2.70 Cw 43.8 tw 0.705 Ix 293
concrete : C20 steel: S420 h=550 mm b=350mm steel rebars : 5Φ18
Situation 4: A W12x106 simply supported beam carries a uniformly distributed load. The properties of the section relevant to the problem are as follow: Use A50 steel and Cb - 1.14 d - 328 mm bf-310 mm tf = 25.1 mm tw = 15.5 mm kdes - 40.4 mm ry - 79.0 mm lx = 388 x 10^6 mm^4 ly - 125 x 10^6 mm^4 Sx - 2380 x 10^3 mm^3 Zx=2690 x 10^3 mm^3 J-3800 x 10^3 mm^3 Cw=2870 x 10^9 mm^6 1. Which of the following nearly gives the Design Strength Moment (LRFD) if the span of the beam is 2.5m? 878 KN-m 793 KN-m 836 KN-m 811 KN m
What is the ultimate uniaxial load capacity of the given column section, according to the design strengths of the materials? Concrete is C30, longitu- dinal steel bars and ties are B420C. Longitudinal bars are o14, ties are o10. b= 300 mm, h= 400mm. The column will be produced on site with adequate quality control. %3D h 1357 kN b) 750 kN 2490 kN d) 1150 kN 1470 kN Leave blank
An S355 Class 1 laterally restrained universal beam (UB) does not support a high shear load. What is its Design Bending Resistance MC,Rd? Give your answer to the nearest whole kNm. Flange thickness tf = 25.5 mm Plastic section modulus Wpl, y = 2,401 cm3 Plastic section modulus Wpl, z = 326 cm3
PROBLEM: A W 21x147 A36 steel beam is subjected to LL=41 KN/m & DL-210 KN applied @midspan as shown. REQUIRED: Investigate the adequacy of the axially loaded A36 steel beam based on flexure, shear and deflection using LRFD method - AISC-NSCP 2010 & 2015 and ASEP Manual. Write your conclusions for each design method using Fy=251 MPa. P= DL LL (KN/m) L=12.10 m
Two beams have the same section. Calculate maximum factored loads as shown below for case (a) and (b) aj bj 1 8m 8m 2-20M SO 5 I A Section for (a) and (b): 350mm BB fé= ↓ Pman = ? 0 ooo 4-25M = 30MPa fy=400мра &man = ? 450mm IS A B 650m ↑ 200mm
Determine the ultimate moment capacity of this beam and identify whether it satisfies the strength requirement. At the limit state strength condition, the beam should satisfy the requirement M* < OMu (where M* is calculated for the strength limit state load 1.2g + 1.5q).
concrete slab with 180 mm thickness support dead load 5kN/m2 include self- weight and service live load 4kN/m?, find: 1- Adequacy of slab thickness. 2- Steel area required at point 1, 2, 3&4. 3- Total load on beam AB and DC. Use Ø12 mm, f = 28MPA and fy = 400MPA