Q16 i. The capacitor sensor is a passive transducer and finds the application in displacement measurement system A three parallel plate capacitor is used in a measurement system, having an area of 200mm x 100cm. The distance between the upper and middle plates is 10mm, distance between middle plate and lower plate is 8mm. If the middle plate is moved down by 8mm with upper and middle plates unmoved, then calculate, Capacitance between upper plate and middle plate. a. b. Capacitance between middle plate and lower plate. ii. Draw the block diagram of a measurement system given the question Q16(i). Assume the sensitivities of C to V Converter is 2V/ 1pF with amplifier gain is 20. Then, calculate the total output voltage of the sensor.

Q16 i. The capacitor sensor is a passive transducer and finds the application in displacement measurement system A three parallel plate capacitor is used in a measurement system, having an area of 200mm x 100cm. The distance between the upper and middle plates is 10mm, distance between middle plate and lower plate is 8mm. If the middle plate is moved down by 8mm with upper and middle plates unmoved, then calculate, Capacitance between upper plate and middle plate. a. b. Capacitance between middle plate and lower plate. ii. Draw the block diagram of a measurement system given the question Q16(i). Assume the sensitivities of C to V Converter is 2V/ 1pF with amplifier gain is 20. Then, calculate the total output voltage of the sensor.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Similar questions

A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
Moving to another question will save this response. Quèstion 3 In half wave rectifier with filter, if the capacitance is increased, the ripple factor increases. True False Moving to another question will save this response. to search 近

An LM317 is connected between two decoupling capacitors. There is a 220ohm resistor between the output pin and the adjust pin. Note the voltage drop between the output and adjust pins is 1.25V. Find the resistor needed between the Adjust pin and ground to ensure 5 V is dropped across the load. Enter your answer in ohms: _ohms
STEP 4: make sure the capacitor is fully charged using the PSB set to 3.3V. Then switch the OAB jumper to 5V and hold SW1 closed again until the LED goes out
Design a clamper circuit to perform the function indicated. Vin Vout 10 V 5.7 v Vin DESIGN Vout -10 V -14.3 V Si diodes
The circle is below(for D1-1N4148 is 1N4148 Diode). and also there have a table(. Note that the first 3 rows of measurement are obtained when the diode is reverse-biased) Vout_dc (V) VD (V) ID (μA) 0.51 -0.51 0.0 0.23 -0.20 0.0 0.10 -0.08 0.0 0.00 0.00 0.0 0.05 0.04 0.0 0.11 0.09 0.0 0.17 0.15 0.1 0.19 0.20 0.1 0.27 0.25 0.4 0.32 0.30 1.6 0.36 0.34 3.1 0.42 0.40 8.2 0.46 0.42 14.3 0.52 0.47 28.0 Questions: 1) plot the diode’s I-V characteristics on a linear scale (ID on the y-axis and VD on the x-axis) 2) [RP4] 3) [RP5]
What is the voltage across the plates of capacitor #1 (C1)? Select one: a. 6.36 volts b. 2.71 volts c. 5.65 volts d. 7.32 volts
Question: In morgan chopper the freewheeling diode gets forward biased because of the stored energy in the Option 1: Inductor Option 2: Resistor Option 3: None of the above Option 4: Сaрacitor
a/ What is the function of the inductance L in a single phase halfwave thyristor? b/ A controlled full wave bridge rectifier has a source of 50 Sinwt with R = 10 and L = 20 mH find the d.c load current if a = 40°, then draw Vo and lo use 50 Hz freq. and B = 1.1n %3D
1. 1-5 K 30v a. what is tue T CTime constant) ? b. How long will it take for the capacutor TO rtach s0% op charge? C. What is tne voltage of capa citor apter 1 seconds? d. How many tíme constants will it take for the soltage to reach 23 v? C. Gweng that the capacitor is fully changed, how will it take por it to be 20% ? long 120v + BF what is the. T ? b. what is the voltage capacitor apter 10 sec? a. C. How many time constants will it take for Tue Vo Itage to reach 80 v.? d. Given that the capaator is Fully charged, how time constants will it be to reau many GOV!
Calculate t for capacitors in parallel and series for charging and discharging
For a single-phase half wave-controlled rectifier with RL load, use the chart below to find the commutation angle ß for the following cases 1) (a=40°, 0=15° then ß= ) 2) (a=80°, 0 =0° then B= ) 3) (α =100°, 0 =45° then = ) 4) (a=120°, 0=75° then ß= 180° Conduction Angle (0) 160° 140° 120° 100 80° 60% 40% 20° 0° p=0 $=15 6=30 + + 20° 40° 60° X6=75 $90 80° 100 120° Delay Angle (0) 140⁰ 160° 180°