Q1. In a digital signal processing technique, an analog signal needs to be sampled wisely into a digital signal which then can be read as a discrete signal. Consider a discrete signal written as w[n] = (1 2 3 2 -1} a) Calculate a delayed version of w[n] by 2 b) Calculate x[n] = 2w[n + 0.5] + u[n+3] - 2u[n-4] using step interpolation

Q1. In a digital signal processing technique, an analog signal needs to be sampled wisely into a digital signal which then can be read as a discrete signal. Consider a discrete signal written as w[n] = (1 2 3 2 -1} a) Calculate a delayed version of w[n] by 2 b) Calculate x[n] = 2w[n + 0.5] + u[n+3] - 2u[n-4] using step interpolation

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Causal signals an=n and bn= 2" are applied to a summation block. Write down the values of the first four terms in the output. ie defined to he the ca.
HW. 1 Q1: A discrete-time signal is shown in the Figure below. Sketch and label each of the following signals: a- ; b- i 01234 3
d. flatline 6. Continuous time signal sin (3m) is sampled at a rate of 4 samples per second. At what sample output value reach to peak value (+1V)? Hint. Simulate with sample index n = 0 to 20 samples. a. n=0 b. n 6 C. n 12 d. n= 4
A typical digital signal processing (DSP) system is given in figure below. ADC has 100MHZ sampling clock and every samples will be captured by FPGA for backend processing. An interpolator increases the sampling rate by a factor of 4 to generate the sample stream of y(n). Then, a decimation block will reduce the sampling rate by a factor of 15 to generate sample stream of z(n). 100MHZ FPGA z(n) Decimator x(t) х(п) y(n) ADC Interpolator LPF1 LPF2 i. When LPF1 (Low Pass Filter 1) and LPF2 are implemented using a 30-taps FIR structure, and the system must operate in streaming way (every samples must be processed without any halt), what will be required FPGA clock frequency and what type of FIR filter structures should be used? Input samples are 12-bits and coefficients are 10-bits for both filters. Determine the number and the size of multiplication and addition operations in FPGA to implement LPF1 and LPF2. Comment on the bit growth and what kind of digital operations should be…
A typical digital signal processing (DSP) system is given in figure below. ADC has 100MHZ sampling clock and every samples will be captured by FPGA for backend processing. An interpolator increases the sampling rate by a factor of 4 to generate the sample stream of y(n). Then, a decimation block will reduce the sampling rate by a factor of 15 to generate sample stream of z(n). 100MHZ FPGA У (n) z(n) Decimator x(t) x(n) ADC Interpolator LPF1 LPF2 When LPF1 (Low Pass Filter 1) and LPF2 are implemented using a 30-taps FIR structure, and the system must operate in streaming way (every samples must be processed without any halt), what will be required FPGA clock frequency and what type of FIR filter structures should be used? Input samples are 12-bits and coefficients are 10-bits for both filters. Determine the number and the size of multiplication and addition operations in FPGA to implement LPF1 and LPF2. Comment on the bit growth and what kind of digital operations should be implemented…
t' 3. Predict the input signal frequencies fi and f2 for the block shown in Figure A3. A₁ sin(2af₁t) A₂ Sin (27f₂t) Figure A3 [M [R Output equation: A/2 [cos (18840t)-cos (43960t)]
b) The following figure shows a sampled signal and the desired sampled signal. A digital signal processing system is required to change the sampled signal to produce the desired output signal. 1 Desired output -1 0 1 2 3 4 5 Sampled signal -0.4 -0.3 i) Design the required digital signal processing system and provide the z-transfer function. Determine and comment on the system's stability.
What is the discrete time signal x[n] given the analog signal in the picture below?
For the signal x[n] shown in the following figure, sketch y[n] = x[-2-n] x [n] ... ... -3 F1 J0 1 2 3 4 5 6 7
Consider the following sampled signal x[n]. What is the cyclic frequency in the sampled signal if the signal was sampled with a sampling frequency of 40 Hz? x[n] = 1 + 2cos((pi/4)n +(pi/3))
A sinusoid signal v(n) = 5 sin( @₂ .n) with f=5 Hz and fs = 10 kHz has to be quantized @ (Vq(n) = Q[v(n)]) with a midtreat quantizer. The range of the signal is ±5 V and the word length of the quantizer 4 bits. The quantizer is at digital full scale. (a) How many quantization levels L does the quantizer have? What is the value of A? (b) Sketch the input-output characteristic of the quantizer. How different is a midtreat quantizer to a midrise quantizer. (c) For time index n = 1250 calculate the quantized value v₁ (n), the quantization error eq(n) and represent vą (n) using RZ code. (d) Calculate the power P of the quantization noise. (e) Determine the SNR in dB.
Generate a single-tone signal whose peak amplitude is 2 V and frequency of 1000 Hz. Use a 20000 Hz sampling rate and a duration of 1 s. Plot the signal for the first 50 points only and observe (listen to) the signal using the wavplay (Note: DO NOT DO THE wavplay COMMAND! It is going to get very noisy in the laboratory. But do include the command in your code.) MATLAB code: