Q1/ from figure below, Draw the free body diagram and determine the horizontal and vertical components of reaction at pin B and the normal reaction at roller A. Also, Determine the force in members AB, AI, FE and FG of the truss by using joint method, and state if the members are in tension or compression. -2 m 40 kN E -2 m- 50 kN D -2 m C 1.5 m B -30 kN 1.5 m 40 kN 1.5 m

Q1/ from figure below, Draw the free body diagram and determine the horizontal and vertical components of reaction at pin B and the normal reaction at roller A. Also, Determine the force in members AB, AI, FE and FG of the truss by using joint method, and state if the members are in tension or compression. -2 m 40 kN E -2 m- 50 kN D -2 m C 1.5 m B -30 kN 1.5 m 40 kN 1.5 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4 kN 4 kN 3 kN 2 kN B C D 3 m H 2'm - 5 m- -5 m- -5 m- - 5 m- Q4- The figure shows a truss that is supported at A by a pin and a roller at E. The truss is subjected to vertical forces. Determine the following: (a) check for zero-force members and identify such members (b) The Force Reactions at the supports are: Ax kN Ay kN Ey k N (c) The internal Force in member CD, FcD i . kN, specify (T) or (C) (d) The internal Force in member CF, FCF İS. . kN, specify (T) or (C) (e) The internal Force in member CD, FcG is . kN, specify (T) or (C)
Q2: The truss shown is supported by a pins at A and G, and subjected to discrete loads as shown in the figure. a) Determine the reaction forces at A and G. b) Use the method of sections to determine the forces in members FE, EB and BC. State whether each member is in tension or compression. G F E 2 m A B C D - 1 m 2 m 1 m 10 kN 15 kN
-5 @ 3m-15m- C F H J K ML boo I A 4@4m=16m B D G E 60 kips A For the truss shown, what is the force in member FG? B what is the force in member BE? + --D
THE DIAGONAL MEMBERS IN THE CENTER PANELS OF THE TRUSS SHOWN ARE VERY SLENDER AND CAN ACT ONLY IN TENSION; SUCH MEMBERS ARE KNOWN AS COUNTERS. DETERMINE THE FORCE IN MEMBER DE AND IN THE COUNTERS THAT ARE ACTING UNDER THE GIVEN LOADING. (15 PTS) Counters ARA B F 6 ft H C E G 3 kips 6 kips 9 kips -S ft- <8 ft- S ft→|<-S ft-
Q₁: Analyze the truss shown below B с <50k 3m IMI A E 100ku EA is Constant for all members + Am X Am
Problem 2: Determine the force in ALL the members of the truss. State if the members are in tension or compression. Show all your work to receive full credit. (Hint: It is not needed to find the reaction forces at C and E if you use the Method of Joints). Note: P1= 1000 lb and P: = 500 lb B C30 45 999 4 ft E 550 D. -4 ft- - 4 ft- 999 299
The rods AB and CD are made of steel having a failure tensile stress of ?FAIL = 500MPa. Using a factor of safety F.S. = 2.0 for tension, determine their smallest diameter so that they can support the load shown. The beam is assumed to be pin connected at A and C. B A 1.5 kn/m 10m Figure 3.1 Suspended Floor Beam D C
Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. For the loading shown and knowing that Es = 200 GPa and E,= 100 GPa, determine (a) the reactions at A and E, (b) the stress at segment BC, (c) the deflection of point D. Dimensions in mm 100 100 -180- -120- A Cl Dl E Steel B Brass 60 kN 40 kN 40-mm diam. 30-mm diam.
F ., É, are applied to the truss system. В a) Find member forces in each member and state if the members are in tension or 4 m compression. b) If the maximum force that any member can support is Tmax in tension and Cmax in compression, determine the maximum value of P that can be supported. A E 3 т 3 m 3 т 3 m F1 F2 F3 F4 F5 Tmax Cmax P 2P 40° 7 kN 8 kN 2P Note: Do not show zero forces in your calculations.
G5 // The bar AB is considered to be absolutely rigid and is horizontal before the load of 10000N is applied. The connection at C is a pin, and AB is supported by the bronze rod EA and the steel rod FB. The length of EA is 1.5m and FB is 2.5m. Neglect any possibility of lateral buckling and the weights of all bars „Calculate the stresses in each rod. For bronze E=100 GPa, A=60 mm? for steel E=200 GPa, A= 25 mm? F Steel L=2.5m B. 3m 2m- Bronze L=1.5m 10000N
The bridge truss shown carries the following uniform live load and concentrated live load. А в с D E A F K G H S@8m LOAD W(LL) P(LL) 15 110 Calculate the following: 5. Maximum force on member BH
The truss in the figure is loaded by four external forces as shown below. Knowing that P1= 3 kN, P2-4 kN, P3-6 kN and P4=2 kN, a= 3 m and h=2 m, you are required to: h P1 P2 a H B members GH, BG, BC. I P3 G C P4 F D a --- a -- a a) Determine the reactions at the supports A and E. b) Using the method of joints, determine the forces of the members at joint A. c) Using the method of joints, determine the forces of the members at joint E. d) Using the method of sections, determine forces on members GF GC, CD. e) Using the method of sections, determine forces on P1 Note: You are required to draw the FBD and apply the equilibrium equations for each case. E