Q1: At a certain section, beam has the cross-section shown in Figure (1) below. The beam is simply supported at its ends with length of 3 m and carries a central concentrated load of 450 kN. For a section at 1 m from the left-hand support, determine the shear stress only at (a) the neutral axis and (b) x. 25 mm 20 mm 12 mm 500 N.A. 50 Activate W Go to S

Q1: At a certain section, beam has the cross-section shown in Figure (1) below. The beam is simply supported at its ends with length of 3 m and carries a central concentrated load of 450 kN. For a section at 1 m from the left-hand support, determine the shear stress only at (a) the neutral axis and (b) x. 25 mm 20 mm 12 mm 500 N.A. 50 Activate W Go to S

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.11.5P: A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used...

See similar textbooks

Similar questions

Repeat Problem 11.3-9. Use two C 150 × 12.2 steel shapes and assume that E = 205 GPa and L = 6 m.
Repeat Problem 11.2-14 using L = 12 ft, ß = 0.25 kips/in., ßRl= 1.5ßL2, and ßR2= 2 ßR1.
1. Question: With a pin on the AB beam A and a short lever BC as shown in the figure is supported. A, B and C pins have a diameter of 18 mm. P and a are given together Take as values given opposite your names in the table. This upload is above, below in your name on the pin (column 5 Calculate the shear stress occurring on only one of the specified pins A, B and C). P(kN)=30 a(0)=60 pin=A 4P 2P 0.5 m 4P 0.5m 1.5 m 1.5 m B
A part of the structure for a facory automation system is a beam that spans 30.0 inches as shown below. Loads that are applied at two points each 8.0inches from a support. The left load F1=1800 lb remains constantly applied while the right load F2=1800 lb is applied and removed frequently as the machine cycles. Find the following: Maximum stress Minimum stress Mean stress Alternating stress Stress ratio Solve the missing parameters in complete solution put necessary diagrams if needed. Thanks
Problem #8: For the beam and loading shown below compute the state of stress at point B (components of the 3x3 matrix), report your answer in ksi to two decimal places. 1.5 in 1.5 in B l in F= 5 kip 3 in 1 in 15 in Fx = 4 kip 3 in Fy = 3 kip
cylindrical pressure vessel has inside diameter d_{o} = 500 mm and inside diameter di=490 mm.if it i made of carbon steel SAE 1040 OQT1300, find the maximum allowable internal pressure if the safety factor against yielding is not to be less than 4. Neglect the external pressure and assume that the longitudinal stresses are taken by the vessel itself. a) Solve using the MSST. b) Solve using the DET. See Appendix 3 for material properties.
Problem B-3 [Design Problem – Simple Loading/2D] A simply supported structure is composed of two members AB and BE (connected by a pin joint at B). Configuration of the structure, pin supports (A and D) and external loadings exerted on the structure are shown in the figure. 500 lb/ft 30° OE BỊ Given the allowable normal stress of AB is 10 ksi, 10 kips determine the minimum cross-sectional area of AB needed 1 ft 1 ft 1 ft to carry the external loadings. Upload Choose a File
Classwork Problem 2 Draw the Shear Force Diagram (SFD) and Bending Moment Diagram (BMD) for a loaded simply supported beam shown below 1KN 5kN 2kN 4KN 1m 1m 2m 1m 1m 14
The beam is supported by a pin at point A and a roller at point C. A distributed load is applied to the beam. Neglect the weight and thickness of the beam. Hints: 1. will need to use similar triangles to find the height after sectioning at B. 2. Review direction of normal force, shear force and bending moment and which is positive or negative. W2 W1 A di d2 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value W1 190 N-m W2 440 N-m di 5 m d2 5 m a. Determine the magnitude of the normal force at point B, NB. . b. Determine the magnitude of the shear force at point B, VB- c. Is the shear force VB a positive or negative shear force? d. Determine the magnitude of the bending moment at point B, MB. e. Is the bending moment MB a positive or negative bending moment? Round your final answers to 3 significant digits/figures.
Write the solution for the following: Member BC= 600 N Member FG = -600 N
In the given figure, support A is a roller and support B is a pin support. If P=15 kips, calculate the 1) vertical reaction at A, 2) vertical reaction at B, 3) horizontal reaction at B P 6 kips 6 kips В 6 ft – 3 ft 2 ft ' 2 ft
1. For the same beam used in IC-13, determine the jump in shear stress at the web-flange junction (at point A). V = 20KN. A 200 mm 20 mm B 200 mm 20 mm 300 mm 2. Now cut off the bottom flange and recalculate the maximum shear stress. (Remove the bottom flange so that the beam has a T-shaped cross-section.)