Q.4) The compound beam shown below is comprised of two beams pinned together at B with a fixed support at A and a roller support at C. Use the shortcut method to draw shear force and bending moment diagrams for the entire length of the beam. Be sure to label all critical values. (Hint: the area under a concave down quadratic curve where the slope of one end is zero can be approximated by Area = bh)

Q.4) The compound beam shown below is comprised of two beams pinned together at B with a fixed support at A and a roller support at C. Use the shortcut method to draw shear force and bending moment diagrams for the entire length of the beam. Be sure to label all critical values. (Hint: the area under a concave down quadratic curve where the slope of one end is zero can be approximated by Area = bh)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.7.12P: A simple beam ACE is constructed with square cross sections and a double taper (see figure). The...

See similar textbooks

Similar questions

Draw the shear and moment diagram of the cantilever beam shown below. For this part, please show the necessary solutions using the long method, not the area moment method. Each correct line/curve with degrees equates to 1 pt. 10 kip 8 kip 3 kip/ft 40 kip-ft 6 ft 4 ft
Draw the shear and moment diagram of the cantilever beam shown below. For this part, please show the necessary solutions using the long method, not the area moment method. 10 kip 8 kip 3 kip/ft 40 kip-ft 6 ft 4 ft
QUESTION 3 If the allowable bending stresses for a beam in one application is 6 kip/in2 in tension. The cross-section of the beam is W8 x 40. If the beam is 10 foot long and simply supported and has a concentrated load applied at x = 3 ft as shown below. • Generate the shear force and bending moment diagram in terms of P; • Based on the allowable maximum bending moment you just obtained above, calculate/ input the mazimm allowable value of the load P: please, pay attention to units, and calculate your answer to 1 decimal place.. 3 ft 7 ft kip.
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a-3.25 m, b=4.75 m, Pg - 35kN, and Pc = 80kN. Construct the shear- force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. A Ay- 58.66 - Dy- Calculate the reaction forces A, and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Answers: a 56.33 (a) V= (b) V- (c) V- B i i PB B kN с kN C Determine the shear force acting at each of the following locations: (a) x-2m (b)x - 4 m (c) x-8 m Note that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2. 3 3 3 KN D b kN D ·x Dy
For the simply supported beam subjected to the loads shown. Let a-3.00 m, b=4.00 m, PB = 30kN, and Pc = 65kN. Construct the shear-force and bending- moment diagrams on paper and use the results to answer the questions in the subsequent parts a ANSWER IN KN B PB Pc C b Calculate the reaction forces Ay acting on the beam. D x
2. For the simply-supported beam shown below, and assuming that P = 200 kip: i) Plot the bending moment and shear force diagrams for the beam. ii) Calculate the bending stress developed in the beam at point A. P 9" T P 4 ft. 8 ft. P 8 ft. L. 24 ft. 8 ft. P wwwwwww. E 1 -24" + HI
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=11 ft, b=6 ft and w = 12 kips/ft.Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.)Answers: Ay = kips, Cy = kips.
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let w = 20.0 kips/ft, a=6.0 ft, and b=20.5 ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. y A A Answers: By a = Calculate the reaction forces By and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Bx = O, it has been omitted from the free-body diagram.) = a i B Cy i = W B b W b kips X kips X
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let w = 20.0 kips/ft, a=6.0 ft, and b=20.5 ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. a A B a W Calculate the reaction forces By and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Bx = O, it has been omitted from the free-body diagram.) B b b X C X
For the simply supported beam subjected to the loading shown, derive equations for the shear force Vand the bending moment M for any location in the beam. (Place the origin at point A.) Let a=2.50 m, b=4.25 m, PB = 45kN, and Pc = 90kN. Construct the shear- force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. Answers: Ay = Dy= Mi i B Calculate the reaction forces Ay and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) PB a PB B a Pc a Pc C kN b KN b D X D₂ X
For the simply supported beam subjected to the loading shown, derive equations for the shear force Vand the bending moment M for any location in the beam. (Place the origin at point A.) Let a=2.75 m, b=5.00 m, PB = 60KN, and Pc = 80kN. Construct the shear- force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. Answers: Ay = Dy= tel tel a i B a Calculate the reaction forces Ay and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) PB B a PB Pc a C Pc C KN b KN D b D X D₂ X
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a-9 ft, b=7 ft and w = 7.5 kips/ft. 21 Answers: Ay= W i a W B Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) 31 a b B b kips, Cy= C i C X Cy X kips.