Q.4)A composite T-beam whose cross-section is shown below is constructed bybonding together of a steel T-beam (E = 200 GPa, Oall = 150 MPa) and tworectangular wood planks (E = 10 GPa, Oall = 9 MPa). Determine the largestpermissible bending moment about the horizontal neutral axis for this compositebeam.200 mm20 mm300 mm75 mm75 mm20 mm

Given Est=Es=200GPa=200×103 MPa σas=150MPa Ew=10GPa=10×103 MPaσaw=9MPa Consider the free body…

Q.4) A composite T-beam whose cross-section is shown below is constructed by bonding together of a steel T-beam (E = 200 GPa, Oall = 150 MPa) and two rectangular wood planks (E = 10 GPa, Oali = 9 MPa). Determine the largest permissible bending moment about the horizontal neutral axis for this composite beam. 200 mm 20 mm 300 mm で 75 mm 75 mm 20 mm

Q.4) A composite T-beam whose cross-section is shown below is constructed by bonding together of a steel T-beam (E = 200 GPa, Oall = 150 MPa) and two rectangular wood planks (E = 10 GPa, Oali = 9 MPa). Determine the largest permissible bending moment about the horizontal neutral axis for this composite beam. 200 mm 20 mm 300 mm で 75 mm 75 mm 20 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.8.8P

See similar textbooks

Similar questions

A composite section consisting of copper and steel carries an axial compressive force P. Both the materials have equal lengths. For steel, A_st=900 [mm] ^2,E_st=200 GPa,o (allowable,st)=140 MPa. For copper, A_cu=1200 [mm] ^2,E_cu=120 GPa,0_(allowable,cu)=70 MPa. Determine the maximum load (kN) the member can carry so that an allowable strain of 0.0005 is not exceeded. A) 210 kN B 105 kN 162 kN D 189 kN
View Policies Current Attempt in Progress A composite beam is made of two brass [E-94 GPa] plates bonded to an aluminum [E-70 GPa] bar, as shown. The beam is subjected to a bending moment of 1850 N-m acting about the z axis. Assume b-57 mm, d₁-43 mm, d₂-9 mm. Determine: (a) the maximum bending stresses Obr. Gal in the brass plates and the aluminum bar. (b) the stress in the brass brj at the joints where the two materials are bonded together. 2 Brass (2) Aluminum (1) Brass (2) Answers: (a) abr = (b) Obrj = i i b MPa, Gal = i MPa. MPa.
Problem 1- A composite T-beam is built up out of plywood and steel angle sections. The steel angle sections have 100 mm long sides and are 10 mm thick. What is the maximum allowable distributed load, w, if we do not want the materials to go beyond their allowable stresses. Given: For plywood: E = 15 GPa, omax = 8 MPa For steel: E = 200 GPa, oma: 150 MPa %3D %3D > 50 K K100> K 100> 3 m: Cross section (dimensions in mm) 200-
1 Situation 19. A composite beam shown is subjected to a bending moment of 500 kN-m. Determine the maximum flexural stress; 300 VIEW INNOVATIONS 200 200 100 55. Experienced by the steel 56. Experienced by the aluminum A. 0.03 B. 25.24 57. Experienced by the brass A. 25.24 B. 37.86 REVIEW I EW INNOVATIONS Steel, E=200 GPa Aluminum, E=70 GPa Brass, E-105 GPa wwwww C. 48.2 D. 72.11 C. 16.8 C. 16.8 D. 11.21 VIEW INNOVATIONS REVIEW INNOVATIONS REVIEW IS
Question 2 Calculate the bending stress at the bottom edge of the following composite beam subject to a bending moment of M= 1500 Nm. The lower section is made from steel (E = 200 GPa) and the upper section is made from aluminium (E = 70 GPa). All dimensions are in mm. 100 YA 100 Z 10 >
A composite beam made of steel and bronze has the cross section shown. The cross-sectional dimensions are b, - 0.9 in, b2 - 2.7 in., and d- 1.8 in. The elastic modulus of the steel is E, - 30,000 ksi, and its allowable bending stress is 17 ksi. The elastic modulus of the bronze is E2 - 15,000 ksi, and its allowable bending stress is 14 ksi. Calculate the allowable bending moment that can be applied about the z centroidal axis. Bronze (2) d Steel (1) b2 Part 1 Your answer has been saved. See score details after the due date. Determine the modular ratio in order to transform the steel into an equivalent amount of bronze. Answer: n- Attempts: 1 of 1 used Part 2 Determine the area moment of inertia of the transformed section about the z-axis. Answer: in.4
A composite beam made of steel and bronze has the cross section shown. The cross-sectional dimensions are bz - 0.9 in, b2 - 2.7 in., and d- 1.8 in. The elastic modulus of the steel is E1 - 30,000 ksi, and its allowable bending stress is 17 ksi. The elastic modulus of the bronze is Ez - 15,000 ksi, and its allowable bending stress is 14 ksi. Calculate the allowable bending moment that can be applied about the z centroidal axis. Bronze (2) d Steel (1) b2 Part 1 Determine the modular ratio in order to transform the steel into an equivalent amount of bronze. Answer: n - i
Q2 For the composite beam shown, find the moment of resistance of the beam when the maximum bending stress in the timber s (14 MPa). For steel (E = 200 GPa) and for wood (E = 10Gpa) 2 A 7 7 r*
1. Three metal striips, each 40 mm height, are bonded together to form the composite beam shown. The modulus of elasticity is 210 GPa for the steel, 105 GPa for the brass, and 70 GPa for the aluminium. If the allowable bending stress for the aluminum (Galow= 100 MPa, for the steel (Galow)kr=150 MPa and (Galow)or 200 MPa for brass determine the maximum allowable intensit of w of the uniform distributed load. Aluminum 10 mm Brass 10 mm Steel 20 mm 40 mm
1. Three metal strips, each 40 mm height, are bonded together to form the composite beam shown. The modulus of elasticity is 210 GPa for the steel, 105 GPa for the brass, and 70 GPa for the aluminium. If the allowable bending stress for the aluminum (Gallow)al= 100 MPa, for the steel (Gallow)st 150 MPa and (Gallow)br=200 MPa for brass determine the maximum allowable intensit of w of the uniform distributed load. 2w 2m Aluminum Brass Steel 40 mm- 10 mm 10 mm 20 mm
Problem 2. A W12×58 acts compositely with a 5-inch-thick concrete slab. The effective slab width is 70 inches. Shoring is not used, and the applied bending moments are as follows: From the beam weight, Mbeam= 15 ft-kips From the slab weight, Malab = 80 ft-kips From the live load, ML = 150 ft-kips Do not consider the construction loads. Steel A992, and f. = 4 ksi. Determine whether the flexural strength of this beam is adequate. Assume full composite action and assume that the formwork provides lateral support of the steel section before curing of the concrete. Assume that W12x58 is a compact section.
Bar A-B-C is made from a fully bonded composite of two materials as shown in the cross section below. Find the Z displacement at point C. A C 1.10 m 20 kN B 1.25 m 50 kN с Y I cross section c-c Uz = 5 mm, material 1 5 mm, material 2 5 mm, material 1 25 mm Material 1 E = 240 (GPa) Material 2 E = 180 (GPa) mm (at C)