Q.3) Two structural members AB and BC (shown below) are connected by a 0.75- inch diameter pin at B that is subjected to two 5-kip horizontal forces. The pins used at A and C are identical to the pin at B. Determine: (a) The maximum average normal stress in members AB and BC. 0.5 in. 1.8 in. B 60° 45% 5 kips 5 kips 0.5 in. 1.8 in. с

Q.3) Two structural members AB and BC (shown below) are connected by a 0.75- inch diameter pin at B that is subjected to two 5-kip horizontal forces. The pins used at A and C are identical to the pin at B. Determine: (a) The maximum average normal stress in members AB and BC. 0.5 in. 1.8 in. B 60° 45% 5 kips 5 kips 0.5 in. 1.8 in. с

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the normal stress at A and B in member CD. Pins C and D are at the centroid of the T section. 5 ft 1.8 kip/ft E15 in. 6 in. A B 12 ft 3 in. 3 in. 1 in. 16 ft
Q9 The bars of the truss each have a cross-sectional area of 780 mm?. If the maximum average normal stress in any bar is not to exceed 140 MPa, determine the maximum magnitude P of the loads that can be applied to the truss. B 0.9 m E -1.2 m- -1.2 m- 0.75 P
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 7 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 5 mm in diameter. Assume a = 640 mm, b = 320 mm. h = 360 mm, and 0= 70% If the normal stress in tie rod (1) cannot exceed 210 MPa and the shear stress in pin B cannot exceed 100 MPa, determine the maximum load max that can be supported by the structure.
5. Determine the magnitude of the load P that will cause a maximum normal stress of max. σ = 30 ksi in the link along section a-a. -2 in.- U a 0.5 in. T P -2 in.-
PROBLEM 2) The rigid bar ABC shown is hinged at A and supported by a steel rod at B. 8) Determine load P that can be applied at C if the stress in the steel rod is limited to 120MP..
A force P of magnitude 1,100 N is applied to the pedal shown satisfies a shearing stress in the pin is 42 MPa. a. Determine the reaction (in N) at the hinge at C. b. Determine the diameter of the pin at C in mm. c. Determine the corresponding bearing stress in the pedal at C in MPa. d. Determine the corresponding bearing stress in each support bracket at C in MPa.
The compound shaft is attached to a rigid wall at each end. a = 2 m and b = 1.5 m. For the bronze segment AB, the diameter is 82 mm and G = 35 GPa. For the steel segment BC, the diameter is 62 mm and G = 83 GPa. The maximum shear stress is limited to 50 MPa in the bronze and 60 MPa in the steel. Compute the largest torque in kN-m that can be applied considering the maximum shear stress of the bronze segment. Compute the largest torque in kN-m that can be applied considering the maximum shear stress of the bronze segment. Compute the largest torque in kN-m that can be applied to the compound shaft. Choose from the choices given above.
The shaft below is fixed at D. A hole with a diameter of 44-mm has been drilled into portion CD of the shaft. If the shaft is made of steel (G = 77 GPa), determine (a) the angle of twist of end A with respect to end D and (b) the maximum shear stress developed in section BC. D 44 mm 0.6 m 60 mm 2000 Nm B 0.2 m 250 Nm 30 mm A 0.4m
2 Link AC has a uniform rectangular cross section 3 mm thick and 12 mm wide. Determine the normal stress in the central portion of the link. (Hint: Link AC has one reaction acts in the direction of the link; and support B is pin support). 75 min 175 mm 150 mm 960 N
Determine the average normal stress in each of the 20-mm diameter bars of the truss. P = 40 kN. 1.5 m (a) determine the normal stress at member AB. (b) determine the normal stress at member BC. (c) determine the normal stress at member AC. (d) If the average normal stress in each of the 20-mm diameter bars is not allowed to exceed 150 MPa, determine the maximum force P that can be applied to joint C
The horizontal rigid beam ABC is supported by vertical bar BD and is loaded by a force P acting at point C as shown in Figure Q2. If the shear stress for each of the 10 mm diameter steel pins at A, B and D is fail = 90 MPa, and the normal stress for the 20 mm diameter rod BD is σfail = 150 MPa. Determine the largest load P that can be suspended from the beam forthe structure to be safe with a safety factor of 2. All pins are single shear.
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 8 mm in diameter. Assume a = 570 mm, b = 285 mm, h = 430 mm, and θ= 55°. If the normal stress in tie rod (1) cannot exceed 200 MPa and the shear stress in pin B cannot exceed 140 MPa, determine the maximum load Pmax that can be supported by the structure.