Q.2 Briefly explain how a variable choke carburettor worksmoving insidegenerated by the engine. The movement is proportionalto engine speed (more RPM the greater the choke area). Attached to the piston is ajet, located in the bodyConstant depression or variable choke carburettors feature aa chamber via ataperedof the carburettor.which moves in and out of a fixedopenings, the piston rises and falls depending onvariations either side of the piston. The action of the tapered needle in the fuel jetDuringallows more or less fuel tointo the passing air therefore the fuel/airremains constant for improved economy and performance at all enginespeeds. Task 8 - Induction SystemsIn order for combustion to take place an induction system is required to feed fuel and air into thecylinder of an engine. To improve efficiency and performance spark ignition (SI) engines are nowadopting compression ignition (CI) engine technology by injecting fuel directly into the cylinderjust before the point of ignition however these engines still require an air induction system.Carburettors: before fuel injection technology had been fully developed carburettors (carbs)were used to create a fuel/air ratio at different engine speeds and loads. A cold start facility wasalso fitted albeit manually operated.The demand for more performance has meant the fixed choke carb' was no longer suitable. Morecomplex carbs' were developed (twin choke) as well as variable choke (constant depression)carbs which used engine vacuum (during throttle opening) to vary the size of choke according tooperating requirements.

A carburetor is a device that aids in the mixing of fuel and air in an internal combustion engine…

Answered: Q.2 Briefly explain how a variable…

Engineering

Mechanical Engineering

Q.2 Briefly explain how a variable choke carburettor works

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Ignition delay can be considered as the duration between the start of injection and startof combustion in diesel engines.• Starting from the injection of the fuel spray, explain the events happening(physical and chemical) in the ignition delay phase. • Explain the advantage of using pilot injection in terms of diesel knocking
Describe with the aid of diagrams the operational sequence of four stroke spark ignition and four stroke compression ignition engines note:Use whatever laws or graphics you need to illustrate the answer
Auto-ignition might occurs in spark ignition .4 engine at low engine speed because the flame velocity is slow and thus the burn time is long, this results in more time for .auto-ignition .True False O Spark ignition engine with high.5 compression ratio can be used with less possibility of auto-ignition by Increasing the inlet temperature Using low octane number fuel O Using high octane number fuel O Reducing the turbulence motion None of the above Cross-flow (in four stroke engine) from .6 cinlet to exhaust occurs the end of the exhaust stroke and the beginning of the induction stroke when O both valves are close the end of the exhaust stroke and the beginning of the induction stroke when O both valves are open At the end of the intake stroke and the beginning of the exhaust stroke when O both valves are open the end of the exhaust stroke and the beginning of the compression stroke O when both valves are open
An HCCI engine needs to compress a fuel-air mixture to 1300 K at top dead center for proper auto- ignition. Assuming a residual gas fraction f of 0.35 at a temperature of 750 K, what should the inlet air temperature be if a.) the compression ratio is 11:1, and b.) the compression ratio is 18:1 ? Assume the specific heat ratio y = 1.35. The problem states that f = 0.35 T = 750 K (exhaust)
1. Use the internet and other reference materials to learn about the internal combustion engines valve system. 2. Illustrate and identify the different components of the ICES valve system. 3. Discuss the function of each component of the valve system of the ICE. 4. Explain the operation of the ICES valve system. 5. Discuss the importance of the valve system in an internal combustion engines.
Which statement(s) is/are TRUE about compression-ignition (CI) engine? OThe maximum indicated mean effective pressure of a naturally aspirated compression-ignition engine is higher than the corresponding values for an equivalent spark-ignition engine. O Unlike spark-ignition engine, there is no knock limit in compression-ignition engine. The pumping loss in a compression-ignition engine is higher that that of an equivalent spark-ignition engine. Engine torque of compression-ignition engine is varied by varying the amount of the fuel injected.
Tumble flow has been found to accelerate .9 the combustion process and improve engine performance and it can be defines :as A rotational air motion around an axis perpendicular to the crankcase axis A rotational air motion around an axis parallel to the cylinder axis A rotational air motion around an axis .perpendicular to the cylinder axis .None of the above O The effects of minimising the distance.10 between the spark plug and the end gas :islare Combustion will be as rapid as possible Producing high engine speeds and thus .higher power output The rapid combustion reduces the time n which the chain reactions that lead to knock can occur All of the above
A spark ignition engine based on Otto cycle has a working temperature range of 25.0 °C and 700.0 °C and its output power is 200 kW. The efficiency of this engine is found to be 56.5%. a. Calculate the compression ratio (r). b. Calculate the input power. c. Calculate the mass flow rate (kg/sec) of air. d. Consider reducing the air emission by 10% while keeping the same materials for key components of the engine, maximum engine temperature of 700.0 °C and input power obtained from part (b). Propose modification and analysis the possible impact on other physical properties. [for air cp = 1.003; c, = 0.717 J/kg-K]
B// An engine having a bore of 120 mm, stroke of 160 mm and compression ratio is 10. It used a fuel mixture of 30% C,H, (butane) and 70% C,H, (propane). The dry products of combustion is CO₂-15%, CO-1.5%, 0,-2.5% and the rest is N₂. Calculate: 1- the air/fuel ratio, 2-the mass of the residual gases left in the cylinder at the end of the exhaust stroke if the pressure and temperature are 1.5 bar and 680 K.
Explain the working of two-stroke, gasoline-driven internal combustion engine?
discuss the Compression-ignition engine its parts and functions
An engine having a bore of 120 mm, stroke of 160 mm and compression ratio is 10. It used a fuel mixture of 30% CH₁ (butane) and 70% C,H, (propane). The dry products of combustion is CO₂-15%, CO-1.5%, 0,-2.5% and the rest is N₂. Calculate: 1- the air/fuel ratio, 2-the mass of the residual gases left in the cylinder at the end of the exhaust stroke if the pressure and temperature are 1.5 bar and 680 K.