Q) Two steel rods (E= 206.84 Gpsi) are attached to rigid supports at A and B and connected to each other at C, All connections are smooth pins, The rod have (25.4 x25.4 mm) square cross-section , A 444.822 KN vertical force is applied at C. Determine the axial stress and the elongation of rod AC. 121 9 cm 274.3 cm

Q) Two steel rods (E= 206.84 Gpsi) are attached to rigid supports at A and B and connected to each other at C, All connections are smooth pins, The rod have (25.4 x25.4 mm) square cross-section , A 444.822 KN vertical force is applied at C. Determine the axial stress and the elongation of rod AC. 121 9 cm 274.3 cm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. The composite bar consists of a 20-mm diameter steel segment AB and 50-mm diameter brass end segments DA and CB. Find the stress on each segment due to the applied loads. E of steel is 200 GPa and E of brass is 101 GPa. 250mm 250mm 250mm 50mm 20mm 50mm 75KN 100KN brass steel brass D B C 75KN 100KN
1. A 60-mm diameter steel tube with a wall thickness of 3 mm just fits in a rigid hole. Determine the tangential stress developed if an axial compressive load of 12 kN is applied. Use v = 0.30 and E = 200 GPa. Answer: 0 = 6.37 MPa 2. A 200-mm long bronze tube closed at both ends fits without clearance in a 70-mm hole in a rigid block. It has a diameter of 70 mm and a wall thickness of 5 mm. The tube then sustained an internal pressure of 4.5 MPa. Use v = 0.33 and E= 83 GPa. Compute the tangential stress in the tube. Answer: Ot = 5.20 MPa
A 2m long bar with square cross section of side 40 mm is subjected to compressive stress of 70 MPa along three mutually perpendicular directions. Take Young's modulus as 200 GPa and Poisson's ratio as 0.3 for the material. Determine change in volume. O a. 1.344 mm3 O b. 1.344 m³ O c. 1344 mm³ O d. 1344 m³
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ = 13 kips, F₂ = 34 kips, and the normal stress in each rod must be limited to 22 ksi, determine the minimum diameter d₁ required for rod (1). A (2) d₁ F₂ B C O 1.087 in. O 0.823 in. O 0.541 in. O 0.867 in. O 1.003 in. d₂
The horizontal cross-section of the cast-iron standard of a vertical drilling machine has the form shown. The line of thrust of the drill passes through P. Find the greatest value the thrust may have without the tensile stress exceeding 15 MN/m2. What will be the stress along the face AB? (Cambridge) 12.4 19.0cm A 36 cm 1.60 cm 1.90 cm 1.60 cmT B. +17.5cm
2. If the allowable shear stress for each of the steel pins at A and B is tpe 6.5 ksi and the allowable normal stress for bar CB is Operm 10 ksi, determine the diameter of the pins at A and B and that of the square bar CB. Pin A is in double shear while Pin B is in single shear. Ignore points D and E. (^ } 2.5 ft -3 ft -5 ft 150 lb/ft Fx =
1. Problem 1: Segment AB of the bar is a hollow tube with an outer diameter of 1.5 inches and a wall thickness of 0.125 inch. Segment BC is a solid rod of diameter 0.75 inch. Determine the normal stress in segment AB in psi. 0.125 in. 0.75 in. 4800 lb 2800 lb 1.5 in. B C |A -6 in.- -6 in. Your answer 2. In Problem 1, determine the normal stress in segment BC in psi. Your answer
Three interconnected cylindrical members are subjected to axial loads as shown below. If the allowable axial stresses are 140 MPa in the steel, 75 MPa in the brass, and 90 MPa in the aluminum, determine the required diameters of each the cylindrical bars. B Brass Aluminum D A Steel 270 kN 245 kN 200 kN -225 kN 0.5 m 0.5 m 0.5 m
1.4 Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 10 kN? Aluminum A=600 mm2 Bronze Steel A=400 mm2 A= 300 mm2 2P 3P 4P P -3 m - - 5 m - - 4 m -
Part 1. A composite assembly of length, L-375 mm, consisting of a steel (G-77 GPa) core (2) connected by rigid plates at the ends of an aluminum [G-35 GPa) tube (1) is shown. The aluminum tube has outside diameter D₁ - 50 mm and inside diameter d₁-30 mm. = 100 MPa, and the The solid steel core has diameter d₂-25 mm. The allowable shear stress of aluminum tube (1) is (rallow) allowable shear stress of steel core (2) is (Tallow)2= 135 MPa. Determine (a) the allowable torque T that can be applied to the composite shaft. (b) the corresponding torques produced in tube (1) and core (2). (c) the angle of twist produced by the allowable torque T. T D₁ L Calculate the polar moment of inertia, J₁, of the aluminum tube. Answer: J₁ (106) mm².
B. SOLVE FOR THE STRESS IN THE ROD IF ITS CROSS-SECTIONAL AREA 1S 2500mm^2. ROD 8=50⁰ A= 2500mm^2 1.5m 3m P=25KN
1200 N 2. For the bone shown to the left, assume the cross-section at C can be approximated as annular, with an outer diameter of 25mm. When the 1200 N forces are applied, the average normal stress in the bone at point C is determined to be 3.80 MPa. Determine the inner diameter of the bone cross section at C. Ans: d; = 14.93 mm 4 in. P 3 in. B 1200 N "UI 8