Q-1A) Identify if TRUE or FALSE, give an explanation for the FALSE onesonly).a. If a homogenous piece of rock is cut into two pieces, then each one will have the same formationfactor.h Micro-resistivity log can be used in oil-based mud and water-based mud systems.L. In a water bearing formation, Ro is equal to the Rt.d. A high GR value always indicates the presence of shale.e One of the most important application of the SP log is to measure the formation permeability.L Caliper log shows a smaller reading that the bit size for evaporite (Salt) layers.g. If the micro-Inverse and micro-Normal logs exhibit positive separation, the permeability of theformation is small.b. A reverse/positive SP deflection occurs when Rmf< Rw.i Water Saturation is defined by the ratio of water volume to the bulk volume of a rock.i The higher formation porosity, the larger invasion diameter.k. Induction log measures the formation resistivity.L Well-logging measurements are recorded while puling the tool up at speed of about 2000 ft/hour.

Since we only solve upto three subparts, we will solve the first three. Please resubmit the question…

Q-1A) Identify if TRUE or FALSE, give an explanation for the FALSE ones only). a. If a homogenous piece of rock is cut into two pieces, then each one will have the same formation factor. h Micro-resistivity log can be used in oil-based mud and water-based mud systems. . In a water bearing formation, Ro is equal to the Rt.

Q-1A) Identify if TRUE or FALSE, give an explanation for the FALSE ones only). a. If a homogenous piece of rock is cut into two pieces, then each one will have the same formation factor. h Micro-resistivity log can be used in oil-based mud and water-based mud systems. . In a water bearing formation, Ro is equal to the Rt.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In NFPA diamond, red indicates the fire hazardEntropy is path functionAccording to hazard and risk assessment, if the occurrence is frequent and catastrophic, then it is unacceptableFor constant volume process, work is zeroA.) If all 4 statements are trueB.) If 3 of the 4 statements are trueC.) If 2 of the 4 statements are trueD.) If only 1 of the 4 statements is trueE.) If none of the 4 statements is true
Q1: Select the correct answer. up to A. Resilience is the energy absorbed by the material a. yield. b. ultimate sensile stress. c. fracture. B. The grain boundaries are a. less chemically active than grains themselves. b. the regions of orientation mismatch of the neighbouring grains. c. classified as linear defects. C. All polycrystalline materials are considered as isotropic because a) they have crystallographic direction-mechanical properties independence relation b) all the crystals' orientations are the same c) the random direction of many grains cancels the anisotropic effect D. Dislocations slip process in metallic crystalline materials a) is essential to explain why the metals exhibit much lower strength than that theoretically predicted based on metallic bonding. b) makes metals and alloys brittle. c) cannot be used to control the mechanical properties of metallic materials E. The atomic stacking ABCABCABC is for d) FCC crystal structure e) BCC crystal structure f) HCP crystal…
Which of the following is not a good match? A )The burning material: Wood, The firefighting material:ABC powder B )The burning material: Plastic, The firefighting material: Water C )The burning material: Magnesium, The firefighting material: Sand D )The burning material: Cooking oil, The firefighting material: Wet chemical E )The burning material: Electrical contact, The firefighting material:Foam spray
5/. is an example for amorphous structure. a. Glass b. Magnesium c. Iron d. Stainless steel
Q/ Correct the under line words 14. Al-4%. Mg alloys are produced by extrusion because has high strength 15. Mg -Zn - Zr alloy is not proper to produce by extrusion because of susceptible to micro porosity and can be used for casting process 16. Brass-alloys are expensive because of difficulties experienced of its casting 17. The density, T.S. and hardness of Fe alloys can be decreased by working
OU DO: 1) An unknown metal, M, has heated and the following heating curve was created. Answer the following with the letter, letter range (ex: A→B) or a temperature. A) Point(s) where only a gas is present B) Temperature at which vaporization occurs C) Point(s) where a mixture of a solid and a liquid are present D) Point(s) where a gas turns into a liquid E) Temperature at which the substance starts to freeze F) Range where there is only a liquid Temperature (K) 1000 900 800 700 600 500 400 300 200 100 0 -100 -200 Heating curve for Unknown Metal, M C A B D Energy added --> E F
H) One of the main copper applications is aluminium, lead ---- I) One of the most important copper alloys is -, aluminium, lead J) Rock copper is while the Scattered copper is
pllllllllllllease solve question 8
the most common oil trap in the world is categorized under type of: Fault trap anticline trap unconformity and lenticular reef trap
Q1/A) Answer only Seven_of the following multiple choice: 1- Brass can be classified in one of the following materials categories: a- Ferrous material. b- Non-ferrous material. c- Composite material. d- Non-metallic. 2- The crystal lattice has a --- a- One dimensional. b- Two dimensional. c- Three dimensional d- Four dimensional. 3- The coordination number for FCC structure is: arrangement а- 2 b- 4 с-8 d- 12 properties c-Mechanical 4- Material density classified as a- Physical. 5- The ability of materials to resist impact is named a- Ductility. 6- One of the following hardness tests are not classified as a macro hardness test: b- Chemical. d- Thermal. b- Toughness. c- Strength. d- Elasticity. a-Brinell hardness. b-Vickers hardness. c- Knoop diamond. d-Rockwell hardness. 7- Due to Allotropy phenomenon, Iron in range of temperature varried between 769 and 910 C° has one of the following names and crystal strutures: a- Gamma (BCC). 8- One of the following hardening processes not need to…
- General Form of Designation. A. Carbon Content in Points or hundredths of percent AISI x x xx B. Major Alloying Elements C. Carbon Content in Points or thousandths of percent 7 8 9 10 D. American Iron and Steel Institute 7. E. Iron Content in Points or hundredths of percent 8. F. Range of Carbon 9 | G. American Institute of Steel and Iron 10. H. Specific Alloy in the Group
Austenite (y) is soft, tough and high ductile True O False