Q-1 The rigid frame shown in Fig.1 is pinned at A and roller supported at D. For the given loading, determine the support reactions and draw the axial force, shear force and bending moment diagrams. 17.5 kN/m

Q-1 The rigid frame shown in Fig.1 is pinned at A and roller supported at D. For the given loading, determine the support reactions and draw the axial force, shear force and bending moment diagrams. 17.5 kN/m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter9: Application Of Influence Lines

Section: Chapter Questions

Problem 11P

See similar textbooks

Related questions

Q: 1. Construct influence line diagrams for vertical reactions at supports A and B and for shear force…

Q: For the frame shown subjected to lateral loads: a. Solve for the support reactions and member end…

Q: Calculate the value and directions of the reactions Calculate and draw the shear force diagram…

A: ∑ MA=0, 6×3.5×3.52-10×5.5×20×5.5-VF×4.5=0 VF=24.28 KN ↑ ∑ V=0;…

Q: 1) Reactions at A and B 2) Shear diagram 3) Bending moment diagram

A: NOTE : Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: Find the reactions and draw the shear force diagram and the bending moment for the figure below: 5…

A: A simply supported beam is given with point load and uniformly distributed load. We need to find out…

Q: The rigid frame shown in Fig. 1 is pinned at A and roller supported at D. For the given loading,…

Q: Q3: Determine the reactions and draw shear force and bending moment diagram

A: In step 1- i included brief introduction about the problem, what need to be solved , what things i…

Q: For the beam in Fig. 2, find the support reactions and sketch the shear force diagram (SFD) and…

Q: Determine maximum value of support reactions, max, shear force at point P and maximum bending moment…

Q: 5.8: For the cantilever beam in Fig. P5.8, determine the maximum upward vertical reaction and the…

Q: 18 kN/m A 5.8m 17 m 22.7 kN/m 10.6m 75 KN D 1. Calculate the reactions at B and C 2. Calculate the…

Q: Determine the reactions and draw the shear and bending moment diagrams for the frame shown in Fig 3:…

A: Given : An indeterminate frame Required : Support reactions, shear and bending moment diagram

Q: Determine the reactions and draw the shear and bending moment diagrams for the three-span continuous…

A: Consider the free body diagram;

Q: Determine the reactions and draw the shear and bending moment diagrams for the two-span continuous…

A: The Step by Step Solution is given below:E=constant.At Joint B: Relative stiffness for…

Q: For the given moment diagram, draw the shear and actual load (indicate the reactions) diagrams.

A: Given:- moment diagram To find:- shear and actual load diagrams

Q: The rigid frame shown in Fig.1 is pinned at A and roller supported at D. For the given loading,…

Q: No.2 45 k 1.8 k/ft A D L10 ft10 ft- -30 ft -10 ft-

Q: Problem 2. Given reaction at A, RA = 63.5 KN, draw the shear force and bending moment diagrams for…

Q: P, = 4.5kN W, = 2.4kN/m W2 = 1.6kN/m P2 = 3.6kN 2.1m 0.9m 1m 1.5m 1.5m 7m

Q: 1. The reaction at the supports will be vertical to the plane of the support if the structure rests…

Q: calculate for the support reactions P=55 -draw the shear diagram -draw the moment diagram

Q: Using the Force Method , determine the reactions and draw the shear and bending moment diagrams for…

A: given beam

Q: Determine the reactions and draw the shear and bending moment diagrams for the beams shown using the…

Q: 1. From the given beam, compute the following: a. reactions at A & B. b. shear and moment at D. c.…

A: Given data:

Q: Determine the support reactions and draw the shear and bending moment diagram

A: Given data

Q: Determine the reactions and draw the shear and moment diagram, by determining the equilibrium…

A: Draw Free body Diagram Consider the moment equilibrium about point A 12×L+8×5-RC×4=0RC=13 kN…

Q: Determine the reactions and draw the shear and bending moment diagrams for the beams shown in Figs.…

A: Solution

Q: For the beam in Fig. 1, find the support reactions and sketch the shear force diagram (SFD) and…

A: Reactions: Consider support point A & B and vertical reactions VA & VB…

Q: Determine the reactions in C and D, the shear force diagram and the bend moment diagram of the…

A: Support Reactions : Taking moment about C, MC = 0-26×1×0.5 + 26×3×1.5 + 56×7 + 104×9 - RD×7 = 0RD =…

Q: The planar frame carries loadings as shown. Determine the reactions at supports A and E and draw the…

Q: Determine the internal shear and moment acting at a section passing through point C in the beam…

A: FREE BODY DIAGRAM: consider left section at c AT C INTENSITY OF LOADING : 318=INTENSITY OF…

Q: 10 kN/m A For the frame shown in Fig.(1), draw axial force, shearing force and bending moment…

A: We have to draw the axial, shear and bending moment diagram

Q: b) For the beam shown Figure Q1.b Calculate the value and directions of the reactions Calculate and…

A: Reactions: A beam with the three supports is a statically indeterminate beam. However, due to…

Q: The 18m long simply supported beam support the distributed load as shown in the image. Use the…

A: Calculate the reaction supports and moments at the supprts.

Q: 5.9: For the beam in Fig. P5.9, determine the extreme value of the shearing force and ben ding…

Q: P y Wo A Мо C D E d

Q: 20KN/m 15KN/m 45kNem 10KN/m tm 4 3 2.5 3.5

Q: 25 kN/m A В 50 kN-m 6 m

Q: Using Force Method, Determine the reactions and draw the shear and bending moment diagrams for the…

A: Solution Given Data

Q: Problem III. Refer to the beam shown below. Given: 81 P (kN) 75 P (kN) 60 kN/m kN/m 2m 1m 3m 3m 90…

Q: Q2: For the beam shown in Fig.(2), find the reaction forces at supports A and B respectively?…

Q: Q1: Determine the maximum live moment at C caused by the moving load for the beam shown in Fig. (1).

A: We will draw influence line diagram for moment at C

Q: Q-1 The rigid frame shown in Fig.1 is pinned at A and roller supported at D. For the given loading,…

Q: 1. a) For the beam shown Figure Q1a Calculate the value and directions of the reactions Calculate…

Q: The dead-weight loading along the centerline of the airplane wing is shown. If the wing is fixed to…

Q: Q. 4: Draw shear force and bending moment diagram of the beam shown in Fig. 4. 6 kN 3 kN/m 18 kN-m D…

Q: Question 4: Analyze the frame shown in fig (c) and draw the shear and moment diagrams for each…

A: Solution; Ds=1 Lets take 'MB' as redundant.

Q: Determine the bending moment M in the cantilever beam at the point located 1.44 ft. to the right of…

Q: The simply supported beam shown in Fig. P.20.4 carries a uniformly distributed travelling load of…

A: using influence line diagram to find shear force and moment at section C of beam

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

Q-1
The rigid frame shown in Fig.I is pinned at A and roller supported at D. For the given
loading, determine the support reactions and draw the axial force, shear force and
bending moment diagrams.
17.5 kN/m
4.5 m
112 kN
в
+ 67.5 kN
6 m
4.5 m
Fig.1
9 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The bridge truss shown carries the following uniform live load and concentrated live load. А в с A B D E 3m K. G S08m W(LL) P(LL) 15 110 Calculate the following: 8. Location of the concentrated live load from the right support in order to get maximum force on member BC. |
Q2 For the frame shown below use the Force Method to find the reactions and draw AFD, SFD and BMD. Assume that the flexural rigidity, El, of beam BC is three times as big as the one of beams AB and DC. 3 m 3 m 10 kN B H EI A 3 kN/m 3EI 8 m ΕΙ D 4 m
For the frame shown below use the Force Method to find the reactions and draw AFD, SFD and BMD. Assume that the flexural rigidity, El, of beam BC is three times as big as the one of beams AB and DC. 3 m 3 m 10 KN B H ΕΙ A 3 kN/m 3EI 8 m C ΕΙ D 4 m
1 (b) Analyze the frame and draw shear force and bending moment diagrams for the following frame. Joint A is pin and D is roller EMA-o - (6e4)(2) - (12«5)(2.5) + Dy(5) = 0 12 kN/m B Dy = 55, 6 FN Ay = 44 kN 16 kN/m 4 m 64 kN %3D AAx 5 m Dy
Q7 A girder having a span of 18 m is simply supported at the ends. It is traversed by a train of loads as shown in Fig. the 50 kN load loading. Find the maximum bending moment using influence line diagrams (ILD). 100 kN 200 kN 100 kN 50 KN W₁ B 3 m 2m W₂ 3m W₂ C 18 m W₁
Frames and Pin Analysis Two members, each consisting of a straight and a 168-mm radius quarter-circle, supports a 500 N load at D and are connected as shown. Determine the forces in member ABC and the force exerted by member DBC on pin C. wy T 168 mm 168 mm T 100 mm Ⓒ E А D 500 N B 54 mm 252 mm-324 mm-
Q.22 The loading, shear force and bending moment diagrams are given in the figure. Determine the position of point of contraflexure y from support B. (4) 21Nm- -In 5KN 30 in O 4KN tending diagram 2m SFD O AND IKN
Beam ABCDEFG below is subjected to multiple loads as show. The total length of the beam is 10m. Analyze the beam completely. 6 kN 10 kN 3 kN/m 2 kN 5 kN-m G 3000mm. 1000mm 1000mm. 2000mm. 1000mm. 2000mm. 3. Determine the shear ation for segment B-C. ** 4. Determine the moment equation of segment C-D.**
Q2: For the frame shown below, determine the pin reactions at D and F on member BG? 500N 3m F 4m 300N D 4m 3m 3m 3m
The columns have the cross sectional areas as shown in the given frame using the cantilever method of analysis. 80 kN P. mL K 100 kN 6 mE F 6 m 4 m 8 m A-6250 mm? A,=5000 A-3750 mm2 A6250 mm mm? O Compute the centroid of the columns cross sectional areas from A. O Compute the horizontal shear at section N. O Compute the reaction of column at D.
Q2: For the frame shown below, determine the pin reactions at D and F on member BG? 500N 3m F 4m 300N D E 4m 3m 3m 3m
What is the vertical reaction at the fixed support? I 4 kips/ft 4 kips/ft E 6 ft 3 ft ++ 3 ft - Select one: а. 28 kips O b. 8 kips C. 9.6 kips d. 36 kips