3 re given three (3) attempts for this assignment.luck and do your best! GOD BLESS!Question 3If it is known that the center pin A supports one-half of the vertical loading shown.6 panels at 12 mE16 m12 m8 kN 8 kN 10 kN10 kN 8 kN 8 kNDetermine the magnitude of the force (in kN) in member AF. Include the negative sign if the member is in compression.« Previous

Answered: Image /qna-images/answer/3875bcee-701e-4777-ab67-c34cff95fc44.jpg

pts for this assignment. and do your best! GOD BLESS! Question 3 If it is known that the center pin A supports one-half of the vertical loading shown. 6 panels at 12 m E 16 m F 12 m 8 kN 8 kN 10 kN -10 kN 8 kN 8 kN Determine the magnitude of the force (in kN) in member AF. Include the negative sign if the member is in compression. « Previous

pts for this assignment. and do your best! GOD BLESS! Question 3 If it is known that the center pin A supports one-half of the vertical loading shown. 6 panels at 12 m E 16 m F 12 m 8 kN 8 kN 10 kN -10 kN 8 kN 8 kN Determine the magnitude of the force (in kN) in member AF. Include the negative sign if the member is in compression. « Previous

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.76P: The 50-ft measuring tape weighs 2.4 lb. Compute the span L of the tape to four significant figures.

See similar textbooks

Similar questions

Two forces X and Y act vertically downward directly at points D and F respectively while force Z acts at point B as shown. Determine the magnitude (N) of the force in member GF if X=649N, Y=454N, Z=115, a=5m and b=3.8m. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate C if force is compressive or T if tensile.
NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Consider the given figure. Given: P = 7 kN and Q = 14 kN. P A Q B C 3 m D The force in members FH is The force in members Flis The force in members G/ is Q E F G 3 m 3 m 3 m KN (Click to select) KN (Click to select) KN (Click to select) V Q V H I A Pratt roof truss is loaded as shown. Determine the force in members FH, FI, and Gl. 3 m Q J K P 3 m 6.75 m L
TDE= TBE Required information The structure consists of pin-connected members. Take X = 4 kN. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. = 2m Determine the force supported by all members. Enter forces as positive numbers if the member is in tension and as negative numbers if the member is in compression. (Round the final answers to four decimal places.) The force supported by all members are as follows: TAB -7.0711 KN TAD= -5 KN TBD= 2.2361 kN KN |1m-1m-1m-1m4 2 kN 3 KN X 3 KN D TEF= TBF= 4.4721 TCF= TBC= -5.6569 kN KN E KN KN F C
What is the axial force in member AB to the nearest 0.1 k? Note that force P2 is parallel to member AB. Include the correct sign. P1 = 25 k P2 = 39 k L1 = 3 ft L2 = 4 ft L3= 6 ft L4 = 4 ft A L1 P1 P2 L2 Type your answer... C
Determine the magnitude (N) of the force in member BC if F=318N, a=0.6m, b=1.47m, r=1.32m and d=32.31 degrees. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate C if force is compressive or T if tensile.
Determine the force in each member of the loaded truss. All triangles are 3-4-5. Enter a positive number if the member is in tension, negative if in compression. 22 KN H C 32kN G 4 panels at 8 m- 15 KN F D E
Question 16 10 20 kN 20 kN 20 kN 3m -40 kN 3m D. 3 m 40 kN- 3 m 6 m Determine the force in member CE. If the force is in compression, write your answer as negative. If the force is in tension, just input the value
Determine the force in members FH, EH and EG shown in Figure 2 using method of sections 1 kN 3 kN 3 kN 3 kN J' 1 kN H 0.46 m F D 2.62 m | B I E 2.4 m 2.4 m 2.4 m 2.4 m
Determine the force in every member of the truss shown. Also state all assumntions and whether each member is in tension or compression. 400 N 2 m 2 m 2 m 45° 45° B 26.6 ° 2 m 2 m Enter your answers here (for the practice exam only - to check your answer) and upload your work to the next question. Round answers to the nearest integer, e.g. 926.5 would become 927. . Member AB o Force in AB o Is AB in Tension (1) or Compression (C)? • Member AD • Force in AD: N. o Is AD in Tension (T) or Compression (C)? • Member BC • Force in BC: N • Is BC in Tension (T) or Compression (C)? • Member BD • Force in BD: N . Is BD in Tension (T) or Compression (C)? • Member CD o Force in CD: o Is CD in Tension (T) or Compression (C)?
1) Determine magnitude of the force the load creates in member FB, which contains the hydraulic cylinder H Express your answer to three significant figures and include the appropriate units. 2) Determine magnitude of the force the load creates in member BD. Express your answer to three significant figures and include the appropriate units.
A 120-kg horizontal beam is supported at the ends A and B. A 340-kg piano rests a quarter of the way from the end A. Part A Determine the magnitude of the vertical force on the support at A Express your answer to two significant figures and include the appropriate units. F = Value Units Submit Request Answer Part B Determine the magnitude of the vertical force on the support at B. Express your answer to two significant figures and include the appropriate units.
Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of the 32° support surface at C. The forces are positive if in tension, negative if in compression. 270 lb Part 1 Correct Find the angle a. 270 lb R Answer: a- 23.75 7.5' 7.5' B 3.3' 32° B 3.3 32°