Procedure: Experiment 1. Prepare 50 mL of an aqueous solution of 0.10M NaHCO3 (sodium bicarbonate, baking soda). 1. Determine how many grams of sodium bicarbonate are required. Show all steps for this calculation, using dimensional analysis with units clearly identified. 2. Prepare this aqueous solution, using a volumetric flask for the precise final volume measurement. It is not a problem to use tap water.

Procedure: Experiment 1. Prepare 50 mL of an aqueous solution of 0.10M NaHCO3 (sodium bicarbonate, baking soda). 1. Determine how many grams of sodium bicarbonate are required. Show all steps for this calculation, using dimensional analysis with units clearly identified. 2. Prepare this aqueous solution, using a volumetric flask for the precise final volume measurement. It is not a problem to use tap water.

Introductory Chemistry For Today

8th Edition

ISBN:9781285644561

Author:Seager

Publisher:Seager

Chapter7: Solutions And Colloids

Section: Chapter Questions

Problem 7.107E

See similar textbooks

Similar questions

Addition of water to concentrated sulfuric acid is dangerous because it generates enough heat to boil the water, causing it to spatter out of the container. For this reason, chemists remember to add acid to water. In a dilution experiment, we calculate the amount of the more concentrated solution that must be measured out. If we place this concentrated solution (Figure 4.7) in the volumetric flask first, then dilute with water, we violate the caution Add acid to water. Describe a safer variation on the method shown in Figure 4.7 that allows the quantitative dilution of concentrated sulfuric acid. Figure 4.7 Preparing a dilute solution from a concentrated solution. (a) Draw the concentrated solution into a pipet to a level just above the calibration mark. (b) Allow the liquid to settle down to the calibration line. Touch the tip of the pipet to the side of the container to remove any extra liquid. (c) Transfer this solution to a volumetric flask. Again touch the pipet to the wall of the flask to ensure complete transfer, but do not blow out the pipet because it is calibrated for a small amount of liquid to remain in the tip. (d) Dilute to the mark with solvent. Frequently, especially with concentrated acids, it is best to have some solvent present in the volumetric flask before you add the concentrated sample.
Graph Table 14.10 shows solubility data that was collectedin an experiment. Plot a graph of the molarity ofKI versus temperature. What is the solubility of KI at55°C?
6-15 Answer true or false. (a) A solute is the substance dissolved in a solvent to form a solution. (b) A solvent is the medium in which a solute is dissolved to form a solution. (c) Some solutions can be separated into their components by filtration. (d) Acid rain is a solution.
Which of the following solutions contains the greatest number of particles? Support your answer. .0 mL of 0 10 M sodium chloride .0 mL of 0.10 M calcium chloride .0 mL of 0.10 M iron(III) chloride .0 mL of 0.10 M potassium bromide .0 mL of 0.10 M sucrose (table sugar)
What volume of 0.250 M NaOH is required to react completely with 0.0100 moles of H2SO4? (a) 80.0 mL (b) 60.0 mL (c) 40.0 mL (d) 125 mL
Mixtures of gases are always true solutions. True or false? Explain why.
Part IV. Preparation of 100 mL 25% Solution X Materials: Solution X, measuring cylinder, distilled water, and parafilm. Show calculation steps. (1) Calculate the volume of Solution X required. (2) Calculate the volume of distilled water required_ (3) Deliver the calculated amount of distilled water in the measuring cylinder. (4) Add the calculated amount of Solution X to the measuring cylinder. (5) Seal the opening of the measuring cylinder with parafilm. Mix well. (6) Transfer the prepared 25% Solution X into a labelled container.
You are asked to weigh 2 g of lithium and add it to 1500 ml of distilled water +2drops of indicator, knowing that the density of water is 1 at room temperaturewhile conducting this experiment. After calculating the amount of LiOH, you need to dilute to prepare 0.25 M of LiOH in a 3000 ml solution. Show your calculation and units.Knowing that the initial volume that you used was 1500 ml. Use this equation to calculate ( CLiOH x VLiOH) before dilution = (CLiOH x VLiOH) after dilution